Tender For Augmentation & Strengthening Chhutmalpur Nagar Panchayat Water Supply Scheme, Saharanpur-Uttar Pradesh

TDR : 55093931

Tender Notice
BOQ

27 Days Left

Saharanpur , Uttar Pradesh

Tender Brief : Tender For Augmentation & Strengthening Chhutmalpur Nagar Panchayat Water Supply Scheme

Document Fees
₹ 23600 /-

EMD
₹ 2379000.0 /-

Tender Value
₹ 23.78 Crore /-

Submission Date
13-05-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Submission of design, drawing,(vetted from any recognized University such as I.I.T), testing of bearing capacity of soil and supply of all material, labour T&P etc. and construct as per tenderer's own seismic proof design and drawings (approved by the department) complete intze Type on raft or pile cum raft foundation with columns and braces R.C.C. Over Head Tank following capacity and staging from made up ground level at site to the top of bottom ring beam of tank, with a minimum free board of 15cm. The design of the tank shall base on safe bearing capacity of soil at site as 8 T/m2 and depth of foundation as 2.50m from existing ground level on pile/raft foundation. made up level of OHT will be taken as 0.70 m above existing gound level. Extra earth required for made up level will be arranged by the contractor at his own cost. If the bearing capacity of soil less than 8 T/m2 than the contractor will submit the design on the same B.C. No extra payment will be paid for this. All other details of tank not covered here shall also be as per specifications enclosed. All Components of OHT will be casted in M-30 concrete with cement, coarse sand and approved stone grit as per I.S. 11682 and I.S. 456. Minimum depth of founditation below original ground level will be 2.50 M. Seismic effects and wind load should be taken into consideration as I.S. 1893 for earthquake resistance and I.S. 875 part-III for wind load on structure. Two coloumn R.C.C. stair case with 1.0 m minimum clear width attached with tank body as an access to Balcony and Top Dome of tank from ground level as per design & drawing with 1.25 m high railling and gate with cabin as per specification including supply of all materials. M.S. ladder made of 50 X 50 X 6 mm angle section and 20 mm plain M.S. bars (specification of M.S. should be as per IS 800-2007) with hand rails of 20 mm medium class G.I. pipes on both sides in three rows from balcony to top dome resting on an RCC plateform (75 X 75 cm and 10 cm thick) projecting from top ring beam and one alluminium ladder inside the tank body ( from manhole in top dome to bootom dome). 1 m wide R.C.C. balcony around the tank at the junction point of vertical wall and conical wall. Proper R.C.C. railing and 20 mm dia medium class G.I. pipe (in 3 rows) on both sides of stair case, arround the balcony at each landing from landing with top ring beam upto manhole on the top dome and at the periphery. The G.I. pipes will be supported on R.C.C. posts of 100 mm dia or on the posts made of 50 X 50 X 6 mm M.S. angle section, spaced at intervals not more than 1.5 m. Proper ventilator at top dome in circular shape of 1.2 m dia along with an R.C.C. cover of minimum 1.50 m dia and 7.5 cm thickness, pillar of vintilator should be minimum 50 cm dia. The space between top dome and R.C.C. cover should be covered with mosquito net of standered qualitity along with expended mentaled jail. Electro Magnetic Flow Meter. Lightening conductor as per I.S.S. 2309 of its latest amendments of latest electricity rules. It should consist proper elevation rod with 5 or more fork points proper down conductors of prescribed mental of proper size prescribed by ISS 2309-1969 and ISS 3013-1966. D.I. manhole of min 60 X 60 cm size made of M.S. channel section with adequate cover made of M.S. sheet of minimum 3mm thickness hinged with manhole with locking arrangment. This manhole should be fixe at top dome at proper place. Supply, fixing, jointing of following size of D.I. D/F Pipes with D.I. D/F specials conforming to IS 8329/2000 as vertical pipes for inlet, outlet, over flow and washout as per latest / relevent I.S. specifications with all jointing materials for proper completion of work including other appurtenant works and execuvation in all types of soil. Construction of bed blocks in 1:2:4 PCC with cement, coarse sand and approved stone grit under each duck foot bend to support the vertical pipes. These bed blocks should supported on the raft not on the soil. Construction of Sluice valve chamber for above sluice valve as per departmental type design and drawing including supply and fixing of C.I. sluice valve including locking arrangement. Construction of washout/ overflow chamber as per departmental type design and drawing. Construction of R. C. C.(1:1.5:3) Floor with minimum reinforcement, Drain & Rain water harvesting, Bye pass arrangement each Rising main , byepass arrangement of over flow pipe all complete and all other necessary work as per departmental drawing and design. Painting of OHT with wheather proof paint (like apex etc.), and Painting of iron work with 1 coat primer & 2 coats of approved emultion paint as per direction of engineer incharge. Testing & Commission etc. all complete work.
2	ZONE-2 700 KL/20M Staging, Outlet 200 mm (DMA-01) -1 No.And Outlet 160 mm (DMA-02)-1 No, inlet 200 mm-03 Nos., Over flow-300 mm-1No., Wash out 150 mm -1 No. Supply and Fixing of following sizes D.I. D/F sluice valves with hand wheels as per I.S.S. 700/1969 or its latest pressure 10 kg/sqcm including cartage from its store to the site of work, lowering them into trenches, fixing in position & testing etc.complete.
3	ZONE-3 2200 KL/22M Staging, Outlet 200 mm (DMA-01) -1 No.And Outlet 160 mm (DMA-02)-1 No, inlet 200 mm-03 Nos., Over flow-300 mm-1No., Wash out 150 mm -1 No. Supply and Fixing of following sizes D.I. D/F sluice valves with hand wheels as per I.S.S. 700/1969 or its latest pressure 10 kg/sqcm including cartage from its store to the site of work, lowering them into trenches, fixing in position & testing etc.complete.
4	ZONE-1 Repairing /Renovaton of Existing 450KL/16.0 M OHT Staging in Zone -1 including leakeage /seepage ,repair with nipple grouting in bottom dome ,conical wall., vertical wall and its finishing and repairing in brace, coloumns ,staircase,balcony etc complete, supply and fixing of ss ladder in water container and in balcony as per requirement ,repairing of railing and sataircase, door ,replacement of ventilator ,lightening conductor , Earthing wire, construction of Rcc floor with 1:1.5:3 ratio ,painting of OHT with apex as per colour code of upjn , repairing of sluice valve and constructon of its chambers, Replacement of inlet,outlet,washout ,overflow pipes ,suppy and fixing of mesh around ventilation of OHT.
5	RISING MAINSupply of the following sizes of D.I. pipes Class K-9 conforming to latest I.S. 8329 / 2000 including their jointing materials and railway freight taxes insurance charges and cartage from store to site of work etc. complete
6	Zone-1, 125mm dia, D.I. K-9
7	Zone-2, 150mm dia, D.I. K-9
8	Zone-3, 200mm dia, D.I. K-9
9	Excavation for rising main trenches in ordinary soil,(lime, clay or sand including lift up to 1.5m and lead up To 50m and refilling, watering, ramming of excavated earth in to trenches and disposal of surplus earth up to 50 m from the center of the foundation trenches.
10	Carting from the store (up to 8 Km.) The following sizes of D.I. double pipe k-9 and specials to the site of work lowering them in to trenches and laying true to alignment and gradient including jointing, testing of pipeline and including supply of jointing material such as nut & bolts, rubber insertion, white lead etc. com- plate but excluding cost of trenching and cutting of pipes etc. For making of lengths but including making joints.
11	Zone-1, 125mm dia, D.I. K-9
12	Zone-2, 150mm dia, D.I. K-9
13	Zone-3, 200mm dia, D.I. K-9
14	Supply of following sizes of CI D/F Sluice valves as per IS 780-1960 tested to 10Kg / Cm2 fixing in pipelines trenches, jointing and testing etc. complete.
15	Zone-1, 125mm dia, D.I. K-9
16	Zone-2, 150mm dia, D.I. K-9
17	Zone-3, 200mm dia, D.I. K-9
18	Carting laying and jointing of the following sizes of CI D/F Sluice valves into the trenches including cost of all jointing material, labour T&P and testing etc. complete of work. 150mm CI D/F Sluice valves
19	Zone-1, 125mm dia, D.I. K-9
20	Zone-2, 150mm dia, D.I. K-9
21	Zone-3, 200mm dia, D.I. K-9
22	Supply of all materials, labours T&P etc. and construction of masonary type sluice valve chamber.
23	Construction of RCC Thrust Block at Bands of pipes
24	DISTRIBUTION SYSTEMSupply and carting ,laying of the following sizes of DI /HDPE pipes (including all specials and solvent) confirming to latest relevant I.S.S with H.D.P.E/DI couplers etc complete in all respect F.O.R. destination including all taxes and insurance.IS -8329/2000 and IS Code 4984:2016 HDPE GRADE-PE-100 HDPE Pipe will be jointed by electrofusion method with all specials and jointing materials as per satisfaction of site incharge.
25	ZONE-1 DI K-7 PIPE (IS - 8329 / 2000)
26	250 mm dia DIK-7
27	200 mm dia DIK-7
28	HDPE PIPE (IS - 4984 / 2016)
29	160 mm dia HDPE PIPE-PN6
30	140 mm dia HDPE PIPE-PN6
31	110 mm dia HDPE PIPE-PN6
32	90 mm dia HDPE PIPE-PN6
33	ZONE-2 DI K-7 PIPE (IS - 8329 / 2000)
34	300 mm dia DIK-7
35	200 mm dia DIK-7
36	HDPE PIPE (IS - 4984 / 2016)
37	160 mm dia HDPE PIPE-PN6
38	140 mm dia HDPE PIPE-PN6
39	110 mm dia HDPE PIPE-PN6
40	90 mm dia HDPE PIPE-PN6
41	ZONE-3 DI K-7 PIPE (IS - 8329 / 2000)
42	500 mm dia DIK-7
43	400 mm dia DIK-7
44	350 mm dia DIK-7
45	250 mm dia DIK-7
46	200 mm dia DIK-7
47	HDPE PIPE (IS - 4984 / 2016)
48	160 mm dia HDPE PIPE-PN6
49	140 mm dia HDPE PIPE-PN6
50	110 mm dia HDPE PIPE-PN6
51	90 mm dia HDPE PIPE-PN6
52	Carting of following size of pipes laying , jointing of DI/HDPE pipe in trenches including lowering ,testing ,and supply of all jointing materials etc complete , HDPE pipe joint by electrofusion methood only
53	ZONE-1 DI K-7 PIPE (IS - 8329 / 2000)
54	250 mm dia DIK-7
55	200 mm dia DIK-7
56	HDPE PIPE (IS - 4984 / 2016)
57	160 mm dia HDPE PIPE-PN6
58	140 mm dia HDPE PIPE-PN6
59	110 mm dia HDPE PIPE-PN6
60	90 mm dia HDPE PIPE-PN6
61	ZONE-2 DI K-7 PIPE (IS - 8329 / 2000)
62	300 mm dia DIK-7
63	200 mm dia DIK-7
64	HDPE PIPE (IS - 4984 / 2016)
65	160 mm dia HDPE PIPE-PN6
66	140 mm dia HDPE PIPE-PN6
67	110 mm dia HDPE PIPE-PN6
68	90 mm dia HDPE PIPE-PN6
69	ZONE-3 DI K-7 PIPE (IS - 8329 / 2000)
70	500 mm dia DIK-7
71	400 mm dia DIK-7
72	350 mm dia DIK-7
73	250 mm dia DIK-7
74	200 mm dia DIK-7
75	HDPE PIPE (IS - 4984 / 2016)
76	160 mm dia HDPE PIPE-PN6
77	140 mm dia HDPE PIPE-PN6
78	110 mm dia HDPE PIPE-PN6
79	90 mm dia HDPE PIPE-PN6
80	Supply of the following sizes of Hand Wheel Type Sluice Valves /Scour valve destination including all taxes and insurance.
81	400 mm dia
82	350 mm dia
83	300 mm dia
84	250 mm dia
85	200 mm dia
86	150 mm dia
87	100 mm dia
88	Scour valve 80 mm dia
89	Supply of underground sluice valves type 80 mm fire hydrant consisting of 80 mm dia tail pieces, 80 mm dia duck foot band and 63 mm dia standard make iron coupling with cap and chain etc. complete to ISS 909 at site.
90	Supply of 50 mm dia screwed down type air valve with gun metal seat at site stone.
91	Carting of following sizes D.I.D/F Sluice valve and specials from departmental store to site of work and lowering them into the trenches, fixing in position and jointing them with pipelines and testing etc. complete (including supply of jointing materials)
92	400 mm dia
93	350 mm dia
94	300 mm dia
95	250 mm dia
96	200 mm dia
97	150 mm dia
98	100 mm dia
99	scour valve 80 mm dia
100	Carting of underground sluice valves type 80 mm fire hydrant consisting of 80 mm dia tail pieces, 80 mm dia duck foot band and 63 mm dia standard make iron coupling with cap and chain etc. complete to ISS 909 at site.
101	Carting of 50 mm dia screwed down type air valve with gun metal seat at site stone.
102	Excavation for pipe line trenches in Ordinary soil,(lime, clay or sand Including lift up to 1.5m and lead up To 50m and refilling, watering, Ramming of excavated earth in to trenches and disposal of surplus earth up to 50 m from the center of the foundation trenches.
103	Dismantling of following type of surface including sorting out and staking of serviceable materials of disposal of unserviceable materials up to a distance of 50 m.
104	B.O.E. ROAD
105	BITUMINOUS ROAD
106	C.C. ROAD
107	INTERLOCKING TILES
108	Permanent Reinstatement of following type of Road surface for laying of pipe line including supply of all materials labour,T&P etc. complete in the direction of engineer in charge.
109	B.O.E. ROAD
110	BITUMINOUS ROAD
111	C.C. ROAD
112	INTERLOCKING TILES
113	Supply of all materials, labour T&P etc. required and construct surface box/masonry type sluice / scour valve chamber as per type design including supply and materials labour, T&P etc. complete.
114	S.V. Chamber (Surface box type)
115	S.V. Chamber (Masonry type)
116	Air valve chamber
117	Fire hydrant chmaber
118	Provision for crossing of nala, & culverts (for 2.50m - 3.50m wide) including shiftijng of telephone cabel etc.along the alignment of pipe line including supply of C.I Tyton pipe and special and also jointing material their laying and jiointing testing etc,complite.
119	Trenchless Technology for the Year 2023350mm dia HDD Trenchless Technology
120	Provision for crossing of nala & culverts (for 1.50m - 2.50m wide) including shiftijng of telephone cabel etc.along the alignment of pipe line including supply of C.I Tyton pipe and special and also jointing material their laying and jiointing testing etc,complite.
121	SCHEDULE FOR HOUSE CONNECTIONMaking New house connection with distribution main supply, carting of specials, lowering them into trenches, fixing them in proper alignment and jointing, including bailing out of water, necessary execvation for connection including all labour, T&P etc. required for proper completion of the works.
122	90 mm to 110 mm dia pipe line
123	125 mm to 160 mm dia pipe line
124	180 mm to 250 mm dia Pipe line
125	300 mm dia to 350 mm dia pipe line
126	Dismantling of following type of surface including sorting out and staking of serviceable materials of disposal of unserviceable materials up to a distance of 50 m. for house connection work.
127	B.O.E. ROAD
128	BITUMINOUS ROAD
129	C.C. ROAD
130	INTERLOCKING TILES
131	Permanent Reinstatement of following type of Road surface for making house connection including supply of all materials labour, T&P etc. complete in the direction of engineer in charge.
132	B.O.E. ROAD
133	BITUMINOUS ROAD
134	C.C. ROAD 1:1.5:3 WITH 1:4:8 BASE CONCRETE
135	INTERLOCKING TILES
136	Making Shifting house connection with distribution main supply, carting of specials, lowering them into trenches, fixing them in proper alignment and jointing, including bailing out of water, necessary execvation for connection including all labour, T&P etc. required for proper completion of the works.
137	90 mm to 110 mm dia pipe line
138	125 mm to 160 mm dia pipe line
139	180 mm to 250 mm dia Pipe line
140	300 mm dia to 350 mm dia pipe line
141	Dismantling of following type of surface including sorting out and staking of serviceable materials of disposal of unserviceable materials up to a distance of 50 m. for house connection work.
142	B.O.E. ROAD
143	BITUMINOUS ROAD
144	C.C. ROAD
145	INTERLOCKING TILES
146	Permanent Reinstatement of following type of Road surface for making house connection including supply of all materials labour, T&P etc. complete in the direction of engineer in charge.
147	B.O.E. ROAD
148	BITUMINOUS ROAD
149	C.C. ROAD 1:1.5:3 WITH 1:4:8 BASE CONCRETE
150	INTERLOCKING TILES
151	Construction of Pump House cum Chloronome and development works Provide all materials, labour, T&P Complete pump house of size (3.60x 3.0x 3.00) m Chloronome of size (2.25 x 2.25 x 3.00) m size including byepass chamber as per type design.
152	ZONE-1, Zone-3
153	BOUNDARY WALL, GATE SITE DEVELOPMENT & APPROACH ROAD (As per Drawing) Proposed W/W
154	Construction of Boundary wall alround water works compound and Tubewell complete including supply of all materials, labour, T&P etc. complete required for proper completion of the works.
155	Supply and fixing of 3.6 M wide gate and 1.2 M wide MS wicket gate including fabrication and supply of steel and construction of boundary pillars etc. complete.
156	Construction of Interlocking type approach road including supply of all materials, labour, tools and plants etc. complete.
157	Provide all materials, labour T&P etc. required for proper completion of work including levelling, dressing excavation and filling of earth where necessary for develop of water works site including carriage of earth.
158	Provision for inside square drain including supply of all materials labour and T & P etc. complete.
159	Construction of Reccharging unit of ground water by rain water in water works sites as per drawing including supply of all material ,labour T&P etc required for proper completion of works
160	Construction LCS AND MCS ROOM
161	E&M work
162	CONSTRUCTION OF TUBEWELL (300x150 mm dia) ZONE-1
163	Transportation, Erection, Dismantling of Rig Machine and its T&P
164	Transportation, Erection, Dismantling of Compressor 250/350 PSI
165	Transportation, Erection, Dismantling of 1 Cusec/ 3 Cusec O.P. Unit and Yield test
166	Supply of Tubewell Assembly M.S.Tubewell assembly with all required parts like plain pipe, Slotted pipe (as required upto 50% of plain pipes) rings, well cap bail plug, clamp reducer, central guide, suport structure etc. as required & as per typed design complete in all respect. (Note- Axial Length of Reducer without Ring shall be measured with casing pipe)
167	300 mm dia M.S. Pipe
168	150 mm dia M.S. Plain/slotted
169	PEA-GRAVEL (As per IS:4097)
170	1.65 mm to 4.50 mm size Pea gravel of Lalkuwan quarry duly screened, washed and properly stacked at site for Tubewell
171	Drilling of bore for tubewell constrution by DC/RC Rig machine complete in all respect including reqired all material, labour etc. as per IS :2800(Part I & II):
172	Drilling of bore by 600 mm dia bit GL to 54 mt. BGL.
173	Drilling of bore by 500 mm dia bit from 54 mt GL to 100 mt. BGL.
174	Drilling of bore by 500 mm dia bit 100 m BGL to 129 m. BGL.
175	Lowering of tube well assembly With M.S. rings, Bail Plug, Reducer Including welding:
176	Lowering of 300 mm dia M.S. Housing pipe from GL to 48 m.BGL
177	Lowering of 150 mm dia M.S. Plain/slotted pipe 48 m. BGL to 100 m. BGL
178	Lowering of 150 mm dia M.S. Plain/slotted pipe 100 m. BGL to 117 m. BGL
179	Development of tube well by 250 PSI air compressor and 1 cusec O.P. Unit to yield sand free discharge.
180	Development and testing of tube well by Air Compressor.
181	Development and testing of tube Well O.P.Unit to yield sand free Discharge.
182	Chemical and Bacteriological
183	test (Analysis of water sample)
184	Logging of borehole by departmental/approved electric logger
185	ESTIMATE FOR CONSTRUCTION OF TUBEWELL (300x200 mm dia) ZONE -2
186	Transportation, Erection, Dismantling of Rig Machine and its T&P
187	Transportation, Erection, Dismantling of Compressor 250/350 PSI
188	Transportation, Erection, Dismantling of 1 Cusec/ 3 Cusec O.P. Unit and Yield test
189	Supply of Tubewell Assembly M.S.Tubewell assembly with all required parts like plain pipe, Slotted pipe (as required upto 50% of plain pipes) rings, well cap bail plug, clamp reducer, central guide, suport structure etc. as required & as per typed design complete in all respect. (Note- Axial Length of Reducer without Ring shall be measured with casing pipe)
190	300 mm dia M.S. Pipe
191	200 mm dia M.S. Plain/slotted
192	PEA-GRAVEL (As per IS:4097)
193	1.65 mm to 4.50 mm size Pea gravel of Lalkuwan quarry duly screened, washed and properly stacked at site for Tubewell
194	Drilling of bore for tubewell constrution by DC/RC Rig machine complete in all respect including reqired all material, labour etc. as per IS :2800(Part I & II):
195	Drilling of bore by 600 mm dia bit GL to 55 mt. BGL.
196	Drilling of bore by 500 mm dia bit from 55 mt GL to 100 mt. BGL.
197	Drilling of bore by 500 mm dia bit 100 m BGL to 140 m. BGL.
198	Lowering of tube well assembly With M.S. rings, Bail Plug, Reducer Including welding:
199	Lowering of 300 mm dia M.S. Housing pipe from GL to 48 m.BGL
200	Lowering of 200 mm dia M.S. Plain/slotted pipe 48 m. BGL to 100 m. BGL
201	Lowering of 200 mm dia M.S. Plain/slotted pipe 100 m. BGL to 130 m. BGL
202	Development of tube well by 250 PSI air compressor and 1 cusec O.P. Unit to yield sand free discharge.
203	Development and testing of tube well by Air Compressor.
204	Development and testing of tube Well O.P.Unit to yield sand free Discharge.
205	Chemical and Bacteriological
206	test (Analysis of water sample)
207	Logging of borehole by departmental/approved electric logger
208	CONSTRUCTION OF TUBEWELL (300x200mm dia) ZONE-3
209	Transportation, Erection, Dismantling of Rig Machine and its T&P
210	Transportation, Erection, Dismantling of Compressor 250/350 PSI
211	Transportation, Erection, Dismantling of 1 Cusec/ 3 Cusec O.P. Unit and Yield test
212	Supply of Tubewell Assembly M.S.Tubewell assembly with all required parts like plain pipe, Slotted pipe (as required upto 50% of plain pipes) rings, well cap bail plug, clamp reducer, central guide, suport structure etc. as required & as per typed design complete in all respect.(Note- Axial Length of Reducer without Ring shall be measured with casing pipe)
213	300 mm dia M.S. Pipe
214	200 mm dia M.S. Plain/slotted
215	PEA-GRAVEL (As per IS:4097)
216	1.65 mm to 4.50 mm size Pea gravel of Lalkuwan quarry duly screened, washed and properly stacked at site for Tubewell
217	Drilling of bore for tubewell constrution by DC/RC Rig machine complete in all respect including reqired all material, labour etc. as per IS :2800(Part I & II):
218	Drilling of bore by 600 mm dia bit GL to 60 mt. BGL.
219	Drilling of bore by 500 mm dia bit from 60 mt GL to 100 mt. BGL.
220	Drilling of bore by 500 mm dia bit 100 m BGL to 170 m. BGL.
221	Lowering of tube well assembly With M.S. rings, Bail Plug, Reducer Including welding:
222	Lowering of 300 mm dia M.S. Housing pipe from GL to 54 m.BGL
223	Lowering of 200 mm dia M.S. Plain/slotted pipe 54 m. BGL to 100 m. BGL
224	Lowering of 200 mm dia M.S. Plain/slotted pipe 100 m. BGL to 155 m. BGL
225	Development of tube well by 250 PSI air compressor and 1 cusec O.P. Unit to yield sand free discharge.
226	Development and testing of tube well by Air Compressor.
227	Development and testing of tube Well O.P.Unit to yield sand free Discharge.
228	Chemical and Bacteriological
229	test (Analysis of water sample)
230	Logging of borehole by departmental/approved electric logger
231	PUMPING PLANT & VOLTAGE STABILIZER FOR NEW/EXISTING TUBEWELL ZONE -1
232	Supply, Installation, testing and Commissioning of 600 lpm ,52 mtr Head Pumping Plant including 24 met coloumn pipe, NRV,CI D/F Bend 90 deg., CI A/F Tee, D/F pipe (1.5 met long-2 Nos and 1 met long- 1 No ), Earthing, Painting,Toolset,wiring of pump house (with internal&external electrification),chainpully block and all pumping plant accessories with nut bolts and rubber packing etc.
233	SITC of suitable capacity soft starter with RS485 port- 400 V Class.
234	SITC of 100 mm dia size mannually operated sluice valves (e&m sor, deduction of actuator rate from actuator valve rate)
235	SITC of 25 kva stabilizer for above
236	SITC of equipments for the items as given below :
237	CE/UL certified Pressure transmitter with display,snubber & gauge coak
238	Automatic Chlorination System compatible to SCADA system
239	CE/UL certified hydostatic type sub soil water level transmitter for tubewell.
240	Misc. Items such as Prtection Ring, Cutout, Electric resistance Rubber sheet, Transformer oil etc.-Sor 2019
241	Coloumn Pipe 3 mtr long
242	ESTIMATE FOR NEW PUMPING PLANT & VOLTAGE STABILIZER ZONE -2
243	Supply, Installation, testing and Commissioning of 900 lpm ,66 mtr Head Pumping Plant including 24 met coloumn pipe, NRV,CI D/F Bend 90 deg., CI A/F Tee, D/F pipe (1.5 met long-2 Nos and 1 met long- 1 No ), Earthing, Painting,Toolset,wiring of pump house (with internal&external electrification),chainpully block and all pumping plant accessories with nut bolts and rubber packing etc.
244	SITC of suitable capacity soft starter with RS485 port- 400 V Class.
245	SITC of 100 mm dia size mannually operated sluice valves (e&m sor, deduction of actuator rate from actuator valve rate)
246	SITC of 40 kva stabilizer for above
247	SITC of equipments for the items as given below :
248	CE/UL certified Pressure transmitter with display,snubber & gauge coak
249	Automatic Chlorination System compatible to SCADA system
250	CE/UL certified hydostatic type sub soil water level transmitter for tubewell.
251	Misc. Items such as Prtection Ring, Cutout, Electric resistance Rubber sheet, Transformer oil etc.-Sor 2019
252	Coloumn Pipe 3 mtr long
253	NEW PUMPING PLANT & VOLTAGE STABILIZER ZONE-3
254	Supply, Installation, testing and Commissioning of 1800 lpm , 63 mtr Head Pumping Plant including 24 met coloumn pipe, NRV,CI D/F Bend 90 deg., CI A/F Tee, D/F pipe (1.5 met long-2 Nos and 1 met long- 1 No ), Earthing, Painting,Toolset,wiring of pump house (with internal&external electrification),chainpully block and all pumping plant accessories with nut bolts and rubber packing etc.
255	SITC of suitable capacity soft starter with RS485 port- 400 V Class.
256	SITC of 150 mm dia size Manuallly operated sluice valves
257	SITC of 60 kva stabilizer for above
258	SITC of equipments for the items as given below :
259	Automatic Chlorination System compatible to SCADA system
260	Pressure transmitter with display
261	CE/UL certified hydrostatic type sub soil water level transmitter for tubewell
262	Misc. Items such as Prtection Ring, Cutout, Electric resistance Rubber sheet, Transformer oil etc.
263	Coloumn Pipe 3 mtr long
264	ESTIMATE FOR LOCAL CONTROL STATION
265	CE/UL & BIS Certified industrial grade LARGE SIZE LED MONITOR with lates configuration as per specification.
266	Desktop/PC with i5/i7 processor for as per spec mentioned in tachnical bid documents.
267	CE/UL Certified 3 KVA UPS with batteries as per spec mentioned in tachnical bid documents.
268	Full development version of required TAGS SCADA Software with coustomization of software for LCS as per spec mentioned in tachnical bid documents.
269	GSM based wireless/Broadband/Equivalent communication system to transfer & receive data & gather data form remote sites to control station,All accessories include signal enhancer antenna along with running expences till DLP.
270	CE/UL certified Firewall for network protection and gateway for providing data to other lcs/mcs.
271	Surge protector for eternet communication protection.
272	industrial grade Ethernet Switch.
273	canon/hp Laser printer1018 or equivalent
274	Installation,Commissioning ,testing including required furniture,internal wiring,PVC panelling of walls/false ceiling work and Split A/C .
275	Security Survelliance IP Camera with required hard drive to store data of atleast 15 Days
276	Charges for operation during trial & Run of 3 months
277	SCADA /AUTOMATION WORK OF NEW PUMPING PLANT ZONE-03
278	CE & UL Certifeid PLC/RTU in IP 54 enclousure suitable to communicate with GSM based modem unit with CPU and power supply with analog anddigital parameter and features as specifeid for tubewell to store and transmit data on GSm backbone RTU/PLC designed with logic to transfer data at multiple statiuonas specifeid.
279	GSM/GPRS based wireless communication with 4G modem for RTU/PLOc capable to transfer & gather data from remote site to controlstation all accessoreis included with signalenhancer antenna made for pumping plant internet charges as specifeid
280	CE/UL certifeid Intelligent Smart Energy Meter
281	CE/UL Certifeid Electromagnetic Flow Meter 150 mm size
282	auto Phase reversal unit of 125 amp rating with inbuilt delay and enclosure control panel etc.
283	CE/UL certifeid Surge Protecter for control panel.
284	CE/UL Certifeid 7 hmi touch screen suitable to communication with PLC/RTU for display & control of process parameters
285	Complete cabling including power cables of all equipment.
286	control panel with IP54 protection ,industrial grade for all equipments.separate for control (24V) and power equipment with capacitor bank panel to improve power factor.
287	Installation, commissioning & testing trial for tubewell
288	OHT AUTOMATION SYSTEM ZONE-03
289	CE/UL certifeid Radar Type level transmitter for OHT.
290	SITC of UPS 10 kva 3phase suitable for operation of Actuators installed at outlet line in case of Power Failure at time of Distribution water supply
291	Lighting at Water works campus with solar panel and LED light of 3 sets
292	Installation, commissioning & testing trial for OHT
293	E/M WORKS IN DMA ZONE-03
294	Designing, Supplying, Installing, commissioning & testing of CE & UL certified Electromagnatic flow Meter with Battery and data communication though GSM Module to PLC SCADA including pressure transducers fittings to facilitate the installation in remote places as specified in the specification of employers requirements for following line sizes-
295	250 mm. dia For feeder line to DMA-1
296	250 mm. dia For feeder line to DMA-2
297	250 mm. dia For feeder line to DMA-3
298	200 mm. dia For feeder line to DMA-4
299	250 mm. dia For feeder line to DMA-5
300	350 mm. dia For feeder line to DMA-6
301	Designing, Supplying, Installing, commissioning & testing of actuator operated CI/DI Globe Valve suitable for drinking water of followings Sizes-
302	250 mm. dia For feeder line to DMA-1
303	250 mm. dia For feeder line to DMA-2
304	250 mm. dia For feeder line to DMA-3
305	200 mm. dia For feeder line to DMA-4
306	250 mm. dia For feeder line to DMA-5
307	350 mm. dia For feeder line to DMA-6
308	Designing, Supplying, Installing, commissioning & testing of Pressure Transmitter Battery Operated CE marked with following technical parameters and Interfacing with PLC module alongwith data communication with SCADA System including Mounting arrangement. Output 4-20 mA / HART / RS 485 Power supply - 24V DC Display - 4\\" LED Accuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
309	Designing, Supplying, Installing, commissioning & testing of Battery operated Residual Chlorine Analyzer single parameter system ready to operate to measure free or total chlorine , Panel made of white PVC (hard foam core, 1100x350x13 mm) with mounting possibility, Pressure reducer, dosing valve for flow regulation, flow through armature, Optical flow measuring, Inlet and Outlet with 0.5\\" hose connection, Temp. 0-50 C, Single parameter controller with PID Controller, 2 current outputs, 3 relay outputs and RS 485 Interface, chlorine measuring sensor for free chlorine membrane covered sensor 0.01 - 2 mg/l , low ph dependency ph 4-9 , 0-50 C, 25 mm dia, 4-20 mA, connection cable 2m., 2-wire, 2 x stripped ends, tinned along with Battery & its required accessories for power backup for continuous operation complete for DMAs.
310	Providing ,erecting and commissioning of MS dismantling joint as per requirement and departments approved drawing and specifications, including machining and rubber ring and suitable for 16 kg/cm2 working pressure with required flanges of suitable side with nut and bolt etc. complete. The joint should have long bolts so that during normal working pressure there should be no sliding movement of sliding flanges LOF (length over flange) should not be less than 75% of dia.suitable for drinking water of followings Sizes-
311	200 mm. dia
312	250 mm. dia
313	350 mm. dia
314	Installation, commissioning & testing trial for tubewell ZONE 1
315	Installation, commissioning & testing trial for OHT ZONE -01
316	SCADA /AUTOMATION WORK OF NEW/ EXISTING TUBEWELL ZONE-1 & NEW TUBEWELLS ZONE-02
317	CE & UL Certifeid PLC/RTU in IP 54 enclousure suitable to communicate with GSM based modem unit with CPU and power supply with analog anddigital parameter and features as specifeid for tubewell to store and transmit data on GSm backbone RTU/PLC designed with logic to transfer data at multiple statiuonas specifeid.
318	GSM/GPRS based wireless communication with 4G modem for RTU/PLOc capable to transfer & gather data from remote site to controlstation all accessoreis included with signalenhancer antenna made for pumping plant internet charges as specifeid
319	CE/UL certifeid Intelligent Smart Energy Meter
320	CE/UL Certifeid Electromagnetic Flow Meter 100 mm size (mjp sor)
321	auto Phase reversal unit of 100 amp rating with inbuilt delay and enclosure control panel etc.
322	CE/UL certifeid Surge Protecter for control panel.
323	CE/UL Certifeid 7 hmi touch screen suitable to communication with PLC/RTU for display & control of process parameters
324	Complete cabling including power cables of all equipment.
325	control panel with IP54 protection ,industrial grade for all equipments.separate for control (24V) and power equipment with capacitor bank panel to improve power factor.
326	Installation, commissioning & testing trial for tubewell ZONE 2
327	OHT AUTOMATION SYSTEM ZONE-01
328	CE/UL certifeid Radar Type level transmitter for OHT.
329	SITC of UPS 10 kva 3phase suitable for operation of Actuators installed at outlet line in case of Power Failure at time of Distribution water supply
330	Lighting at Water works campus with solar panel and LED light of 3 sets
331	OHT AUTOMATION SYSTEM ZONE-02
332	CE/UL certifeid Radar Type level transmitter for OHT.
333	SITC of UPS 10 kva 3phase suitable for operation of Actuators installed at outlet line in case of Power Failure at time of Distribution water supply
334	Lighting at Water works campus with solar panel and LED light of 3 sets
335	Installation, commissioning & testing trial for OHT
336	E/M WORKS IN DMA ZONE-01
337	Designing, Supplying, Installing, commissioning & testing of CE & UL certified Electromagnatic flow Meter with Battery and data communication though GSM Module to PLC SCADA including pressure transducers fittings to facilitate the installation in remote places as specified in the specification of employers requirements for following line sizes-
338	200 mm. dia For feeder line to DMA-1
339	200 mm. dia For feeder line to DMA-2
340	Designing, Supplying, Installing, commissioning & testing of actuator operated CI/DI Globe Valve suitable for drinking water of followings Sizes-
341	200 mm. dia For feeder line to DMA-1
342	200 mm. dia For feeder line to DMA-2
343	Designing, Supplying, Installing, commissioning & testing of Pressure Transmitter Battery Operated CE marked with following technical parameters and Interfacing with PLC module alongwith data communication with SCADA System including Mounting arrangement. Output 4-20 mA / HART / RS 485 Power supply - 24V DC Display - 4\\" LED Accuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
344	Designing, Supplying, Installing, commissioning & testing of Residual Chlorine Analyzer single parameter system ready to operate to measure free or total chlorine , Panel made of white PVC (hard foam core, 1100x350x13 mm) with mounting possibility, Pressure reducer, dosing valve for flow regulation, flow through armature, Optical flow measuring, Inlet and Outlet with 0.5\\" hose connection, Temp. 0-50 C, Single parameter controller with PID Controller, 2 current outputs, 3 relay outputs and RS 485 Interface, chlorine measuring sensor for free chlorine membrane covered sensor 0.01 - 2 mg/l , low ph dependency ph 4-9 , 0-50 C, 25 mm dia, 4-20 mA, connection cable 2m., 2-wire, 2 x stripped ends, tinned along with Battery & its required accessories for power backup for continuous operation complete for DMAs.
345	Providing ,erecting and commissioning of MS dismantling joint as per requirement and departments approved drawing and specifications, including machining and rubber ring and suitable for 16 kg/cm2 working pressure with required flanges of suitable side with nut and bolt etc. complete. The joint should have long bolts so that during normal working pressure there should be no sliding movement of sliding flanges LOF (length over flange) should not be less than 75% of dia.suitable for drinking water of followings Sizes-
346	200 mm. dia
347	E/M WORKS IN DMA ZONE-02
348	Designing, Supplying, Installing, commissioning & testing of CE & UL certified Electromagnatic flow Meter with Battery and data communication though GSM Module to PLC SCADA including pressure transducers fittings to facilitate the installation in remote places as specified in the specification of employers requirements for following line sizes-
349	200 mm. dia For feeder line to DMA-1
350	300 mm. dia For feeder line to DMA-2
351	Designing, Supplying, Installing, commissioning & testing of actuator operated CI/DI Globe Valve suitable for drinking water of followings Sizes-
352	200 mm. dia For feeder line to DMA-1
353	300 mm. dia For feeder line to DMA-2
354	Designing, Supplying, Installing, commissioning & testing of Pressure Transmitter Battery Operated CE marked with following technical parameters and Interfacing with PLC module alongwith data communication with SCADA System including Mounting arrangement. Output 4-20 mA / HART / RS 485 Power supply - 24V DC Display - 4\\" LED Accuracy - +/- 0.1 % of full scale or better Enclosure- IP 68
355	Designing, Supplying, Installing, commissioning & testing of Battery operated Residual Chlorine Analyzer single parameter system ready to operate to measure free or total chlorine , Panel made of white PVC (hard foam core, 1100x350x13 mm) with mounting possibility, Pressure reducer, dosing valve for flow regulation, flow through armature, Optical flow measuring, Inlet and Outlet with 0.5\\" hose connection, Temp. 0-50 C, Single parameter controller with PID Controller, 2 current outputs, 3 relay outputs and RS 485 Interface, chlorine measuring sensor for free chlorine membrane covered sensor 0.01 - 2 mg/l , low ph dependency ph 4-9 , 0-50 C, 25 mm dia, 4-20 mA, connection cable 2m., 2-wire, 2 x stripped ends, tinned along with Battery & its required accessories for power backup for continuous operation complete for DMAs.
356	Providing ,erecting and commissioning of MS dismantling joint as per requirement and departments approved drawing and specifications, including machining and rubber ring and suitable for 16 kg/cm2 working pressure with required flanges of suitable side with nut and bolt etc. complete. The joint should have long bolts so that during normal working pressure there should be no sliding movement of sliding flanges LOF (length over flange) should not be less than 75% of dia.suitable for drinking water of followings Sizes-
357	200 mm. dia
358	300 mm. dia
359	Three month Trial & Run
360	Three month Trial & Run Expenditure on hypo chloride solution and Chaukidar, Watch &Ward for Existing Tubwells zone 1
361	Three month Trial & Run Expenditure on hypo chloride solution and Chaukidar, Watch &Ward for New Tubwells zone 2
362	Three month Trial & Run Expenditure on hypo chloride solution and Chaukidar, Watch &Ward for New Tubwells zone 3 Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Water Storage and Supply Tenders

Water Supply Project Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Augmentation & Strengthening Chhutmalpur Nagar Panchayat Water Supply Scheme, Saharanpur-Uttar Pradesh

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Augmentation & Strengthening Chhutmalpur Nagar Panchayat Water Supply Scheme, Saharanpur-Uttar Pradesh

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us