|
| 1 | Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material up to a lead of 1000m including removal and disposal of top organic soil not exceeding in 150 mm thickness as per MoRTH specification clause 201 - By mechanical Means. - In area of light jungle |
| 2 | Dismantling of flexible pavements and disposal of dismantled materials up to a lead of 1000 meters, stacking serviceable and unserviceable materials separately as per MoRTH specification clause 202. By Mechanical Means. Bituminous courses |
| 3 | Providing, laying, spreading and compacting stone aggregate for Wet Mix Macadam (as per table 400-12 and 400-13) specification including premixing the material with water to OMC in wet mix plant as per approved design mix, carriage of mixed material by Tipper to site, laying in uniform layers with motor grader/Front end Loader/paver finisher, in sub base/ base course on a well prepared under base and compacting with vibratory roller to achieve the desired density including lighting, guarding, barricading and maintenance of diversion etc. (MoRTH specification : Clause 406 & Clause 112) by mechanical means with all lead . |
| 4 | Providing and applying primer coat over prepared surface or granular base with bitumen emulsion SS-1 as per IS: 8887 & manufacturer’s specifications @ 6 kg /10 Sqm with a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification CI 502 & 112 (Including cleaning of road surface ) |
| 5 | Providing and laying Dense Bituminous Macadam on prepared surface with specified graded crushed aggregates as per table 500-8 & 500-10 and design mix for base/binder course including loading of material with Front end loader, heating of binder (including cost of anti-stripping compound wherever required) aggregate and filler as per table 500-9, in hot mix plant More than 60-90 TPH, transporting the mixed material by tippers and laying with sensor paver finisher as per clause 505.3.5 to the required level and grade rolling by self propelled power rollers and vibratory rollers or pneumatic tyred roller 150-250KN. TP=0.7MPa to achieve the desired density (approved by the department) but excluding cost of primer/tack coat. [MoRTH Specification : Clause 505 & 112] with all leads. Grading II (26.5mm nominal size) - Bitumen @ minimum 4.5% of mix using VG 40 ( thickness 50 - 75 mm ) |
| 6 | Providing and applying tack coat on the prepared surface, with bitumen emulsion RS-1 as per IS : 8887 & manufacturer’s specifications @ 2 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MoRTH specification Clause 503 & 112 ( Including cleaning of bituminous road surface ) |
| 7 | Providing and laying bituminous concrete as per design mix on prepared surface with specified graded stone as per table 500-16 & 500-17 for wearing course including loading of aggregate with Front end loader and hot mixing of binder (including cost of anti-stripping compound, wherever required) and filler as per table 500-9 with aggregates in hot mix plant More than 60-90 TPH Transporting the mix material with tipper and laying with sensor paver finisher (as per clause 507.3.5) to the required level , grades and rolling with vibratory compactor and pneumatic tyred roller 150-250 KN,TP=0.7 Mpa, to achieve the desired density (approved by the department) excluding cost of primer/tack coat (MoRTH Specification : Clause -507 & 112) with all lead. Grading II (13.20 mm nominal size) - Bitumen @ minimum 5.40% of mix & thickness 30 - 40 mm VG 40 Grade |
| 8 | Providing laying spreading and compacting specified graded sand, gravel (crushed stone) as per Table 400-1,400-2 or any other course material as per design mix, as per CBR in sub base course including premixing the material at OMC in wet mix plant, carriage of mixed material spreading in uniform layers with motor grader F.E loader on a prepared base and compacting with vibratory roller to achieve desired density (as per I.S.2720) including all material, labor, machinery, lighting guarding, barricading and maintenance of diversion complete.[MoRTH specification : Clause 401]. By mechanical means with all lead |
| 9 | Providing and laying marking of center line and stop line and zebra crossingetc with hot thermoplastic compound of approved quality with type-1 glass beeds (Table-800-9) , 2.5 mm thick on road/ plain surface, including reflectorising glass beads type-2 (Table-800-10) @ 250 gms per sqm area with special applicator machine, as per IRC:35 including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control involved. The finished surface to be level, uniform and free from streaks and holes as per clause 803 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. |
| 10 | Raised Payment Marker (Cats Eye): Supplying and Fixing of Molded Shank Raised Pavement Markers made of ABS Moulded body and Polycarbonate Reflective panels with Micro Prismatic Lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 35000 Kilogram tested in accordance to ASIM D 4280 & ASTM D 788. The Height of Road Stud is 20mm, Width 100mm, Length 100mm and minimum reflective area of 13 sqcm on each side.The Strength of detachment of the integrated cylender shank not less than 14+/-2mm (Thickness) and height not less than 30+ 2mm from the body. Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive |
| 11 | Solar Raised Pavement Markers: As per ASTM D 4280 & ASTM D 788 Supply & Installation of Solar Raised Pavement Markers made of Aluminium Alloy Body with Squre shape, solar powered, LED self illumination in active mode. The solar stud marker shall support a load of 25000 kg tested in accordance to ASTM D 4280. The marker should be resistant to dust and water ingress according to lS:12063:1987 standard and should withstand temperatures in e of 10°C to 75°C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency blinking is 2Hz. There should be super bright LEDs (one gach side with over 5000 (Milicandle) luminous intensity) and its visibilty should not less than l000meter distance in night. The Height, width and length of the marker shall be less than 20mm,125mm, 125mm and it should have one cylinder type shank 30mm + / - 2mm and length of shank should be 60mm +1-5mm. Fixing will be by drilling holes on the road for the shanks , to go inside, without nails and using epoxy resin based adhesive |
| 12 | Random Rubble stone masonry for superstructure up to 4.5 Mtr. height above plinth/bed level in cement sand mortar for above 30cm thick walls - In cement sand mortar 1:4 |
| 13 | Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces - Old Suface |
| 14 | Supplying and fixing pre cast R.C.C. stones (M-15 mix) using one percent steel reinforcement, including finishing in cement sand mortar 1:3, earthwork, cement concrete 1:4:8 engraving letters and numerals, painting with enamel paint etc. complete as per IRC standard design. |
| 15 | Km. Stone for NH, SH & MDR ( size 35 x110x25 cm) |
| 16 | 5th Km. Stone ( size 50 x152x25 cm) |
| 17 | 200 Meter stone ( size 15 x10x65 cm) |
| 18 | Supply of Chevron sign of size 75x60 cm made out of aluminum sheet 2 mm thick with fixing provision on M.S. angle iron post 50x50x6 mm 3 M long screwed with stainless steel nut bolts of 8 M dia, plate is covered by high intensity grade yellow retro-reflective sheeting and black screen printed arrow on Retro Reflective Sheet, complete in all respect. Comp. in all respect duly post painted in alternate band of Black/White synthetic enamel paint & hold fast at bottom |
| 19 | Supplying cautionary / warning sign board 90 cm equilateral triangle made out of 2.0 mm thick aluminum sheet riveted on a frame of 40X40X3mm angle Iron, face to be fully covered by white / blue high intensity grade retro reflective sheeting with Red/white symbol, cut out or screen printed background with epoxy paint complete confirming to MoRTH specifications (2013) Cl. 801 with angle iron post 65 x 65 x 6 mm. Comp. in all respect duly post painted in alternate band of Black/White synthetic enamel paint & hold fast at bottom |
| 20 | Supplying Informatory sign board size 60x80 cm. made out of 2.0 mm thick aluminum sheet riveted on a frame of 40X40X3mm angle Iron, face to be fully covered by white / blue high intensity grade retro reflective sheeting with Red/white symbol, cut out or screen printed background with epoxy paint, complete confirming to MoRTH specifications (2013) cl. 801 with angle iron post 65 x 65 x 6 mm.3 Mtr. Long. Comp. in all respect duly post painted in alternate band of Black/White synthetic enamel paint & hold fast at bottom |
| 21 | Supply or Retro-reflective Name Board size 600x900 made out of 2mm thick aluminum sheet fixed on post and frame made out or angle iron 50x50x6mm, 3M long using stainless steel nut bolts of 8 mm dia, aluminum sheet is covered with high intensity grade Retro-reflective sheeting and non reflective letters in black, post duly painted in black and white synthetic enamel, complete in all respect. Confirming to MoRTH specifications (2013) c1. 801. - SIZE 900x1200 mm |
| 22 | Mandatory/ Regulatory retro reflective sign boards 60 cm Dia made out of 2.0 mm thick aluminum sheet riveted on a frame of 40X40X3mm angle Iron, face to be fully covered by white/ blue high intensity grade retro reflective sheeting with Red/white symbol, cut out or screen printed back ground with epoxy paint, confirming to MoRTH specifications. (2013) CI. 801 with angle iron post 65x65x6 mm 3 M.long. Comp. in all respect duly post painted in alternate band of Black/White synthetic enamel paint & hold fast at bottom |
| 23 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. 90 cm high octagon |
| 24 | Installation of sign board having the post like mandatory cautionary & informatory board includes excavation, cement concrete 1:5:10 (30X30X60) cm and transportation complete. |
| 25 | Supply of Hazard Marker made out of 2 mm thick M.S. sheet size 300x300x3 mm framed with angle iron 25x25x3 mm and fixed on channel posts 75x40x6 mm and hold fast at bottom whole body is painted in white stoving enamel and 6 Nos., 5 cm dia reflective sheet on white reflective background with additional border of 1.25 cm all around it. |
| 26 | Fixing of Hazard marker including excavation & cement concrete (1:3:6) (30x30x30cm size) in foundation, curing complete as per specifications. |
| 27 | Earth work in excavation for foundation of structure complete with all lift, dewatering shoring and shuttering etc. .including refilling of trenches in 25.mm layers, ramming, watering and disposal of surplus soil within a lead of 1000 meters, as per drawing and technical specification.[MoRTH Specification : Clause : 304]. In ordinary Soil [MoRTH Specification : Clause : 301]. Depth up to 3m |
| 28 | Structural cement concrete (Design Mix) in open foundations, with form work, at any level.Cement concrete for plain/reinforced concrete in open foundation as per drawing and technical specification. [MoRTH Specification : Section 1700(N)&1500(N)]. Using Batching Plant, Transit Mixture, and Concrete Pump. P.C.C.M-15 grade. |
| 29 | Structural cement concrete (Design Mix) in open foundations, with form work, at any level.Cement concrete for plain/reinforced concrete in open foundation as per drawing and technical specification. [MoRTH Specification : Section 1700(N)&1500(N)]. Using Batching Plant, Transit Mixture, and Concrete Pump. R.C.C.M-20 grade |
| 30 | Steel reinforcement in substructure complete.[MoRTH Specification : Section 1600(N)] HYSD bar reinforcement |
| 31 | Deduct @ 18% GST Please Enable Macros to View BoQ information |
| 32 | Deduct @ 18% GST Please Enable Macros to View BoQ information |
