|
| 1 | M&L for repairing of RCC projection,chajja, facia, column etc by necessary preparation (i.e scraping,cutting, chiseling, dustimg and cleaning exposed reinforcement surface of damaged/loose surface and applying one coat of cement slurry and nitobond chemical as per manufacturer instruction and filling the surface with plain cement concrete (1:1.5:3)reinforced with welded mesh and make good bt 15 mm thick plaster with CM (1:4) and including scaffolding/formwork etc upto double storey height complete all as specified and directed by engineeer in charge |
| 2 | M & L for sunken treatment, application of one coat of water based bitumen emulision primer @ 0.3 lit per sqm including cleaning of surface thoroughly from dust & dirt. Lay water proofing treatment with polymetric memberane 3 Kg/ sqm standard consisting of 90 micron, HMHDPE torch on memberane over a coat of blown bitumen 85/25 @ 1.2 Kg/sqm on top of memberane and providing 25 mm thick sand cushioning to recieve lean concrete in sunken floor complete and 10mm plaster in CM 1:4 using WPC over PCC 1:2:4 using 12.50mm store aggregate as required depth including demolotion of suken floor etc complete all as specified and directed by the Engr-in-Charge. |
| 3 | M&L fly ash brick work with sub class 'B'brick straight or curved on plan exc 6m mean radius built cement mortar 1:6 inclduing demolition of brick work built in CM and disposal of debris and rubbish to low level area/500 mtr from site complete all as specified and as directed |
| 4 | M&L renderig/screeding 15mm thick cment mortar 1:6 on fair faces of brick or concrete surface of wall rendering is to be finished even smooth with out using extra cement complete all as directed by the Engineer - In- Charge. |
| 5 | M&L Preparing newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed by Engr-in-Charge. |
| 6 | Cleaning and removing all scale and dirt , etc from tanks and from mouths of circulating pipes etc exc 250m & not exc 500 ltr capacity including disconnecting and setting aside or refixing in old position and as directed. Note: Date of cleaning to be mentioned with black/white synthetic enamelled paint after cleaning of tank by the contractor without any extra cost to the Govt . |
| 7 | All as per ser item No above but 1000 ltr capacity |
| 8 | Taking up or down existing steel tubing 15 mm dia bore and connections including cleaning for refixing or removal to store complete all as specified and as dircted. |
| 9 | Taking up or down existing steel tubing 20 mm dia bore and connections including cleaning for refixing or removal to store complete all as specified and as dircted |
| 10 | Taking up or down existing steel tubing 25 mm dia bore and connections including cleaning for refixing or removal to store complete all as specified and as dircted. |
| 11 | Supply and fixing, jointing and testing galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings for 15mm dia bore, the rate also included for cutting through walls floors etc. |
| 12 | Supply and fixing, jointing and testing galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings for 20mm dia bore, the rate also included for cutting through walls floors etc. |
| 13 | Supply and fixing, jointing and testing galvanised iron tube medium grade with all fittings such as bends, elbows sockets, reduces etc and fixed to wall, ceiling or laid in floor with new fittings for 25 mm dia bore, the rate also included for cutting through walls floors etc. |
| 14 | Fixing only old steel tubing 15 mm dia bore and connections obtained from taking down against item No 8 herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings. |
| 15 | Fixing only old steel tubing 20 mm dia bore and connections obtained from taking down against item No 9 herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings. |
| 16 | Fixing only old steel tubing 25 mm bore and connections obtained from taking down against item No 10 herein before in new or old position fixed to wall, ceiling or laid in floor with new fittings. |
| 17 | S& F 500 Ltr capacity of rotational moulded polyethylen water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including Dismantling water tanks and removing to store of steel/PVC of capacity exceeding 250 ltr but not exceeding 500 Ltr complete all as specified and as directed by the Engineer-In- Charge. |
| 18 | S& F 1000 Ltr capacity of rotational moulded polyethylen water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including Dismantling water tanks and removing to store of steel/PVC of capacity exceeding 500 ltr but not exceeding 1000 Ltr complete all as specified and as directed by the Engineer-In- Charge. |
| 19 | S & F 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (minimum weight 20mm 210 gm) complete all as specified. |
| 20 | S & F in repair 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed (minimum weight 20mm 210 gm) complete all as specified. |
| 21 | S & F 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. |
| 22 | S & F in repair 20mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. |
| 23 | S&F in repair PVC lid /cover with locking arrangement for water storage tank 500 ltrs capacity and as directed . |
| 24 | S&F in repair PVC lid /cover with locking arrangement for water storage tank 1000 ltrs capacity and as directed . |
| 25 | S&F in repairs 15mm bore bib taps cast copper alloy with crutch screwed for iron pipe or for brass ferrule complete all as specified and as directed |
| 26 | S&F in repair pillar tap 15mm bore chromium plated fancy types cast copper alloy with capstan heads, screwed down high pressure with or without letter 'Hot' or 'cold' with long screwed shanks and flynuts screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 27 | S&F PVC connection 15mm size with PTMT nuts of length 450 mm complete all as specified and directed. |
| 28 | Supply and fixing in repair PVC waste pipe with 32 mm bore and 65 cm long with cap complete all as specified and directed. |
| 29 | S&F in repairs 15mm dia bore cast copper alloy chromium plated fancy type angle cock with long shank & cup (concealed type) complete all as specified and as directed. |
| 30 | S&F in repair concealed stop cock fancy type CP cast copper alloy screwed down high pressure with crutch or buttor fly handle screwed both ends for iron pipe or for unions and fixed 15mm bore complete all as specified and directed. |
| 31 | S&F in repairs centre hole WHB mixture cp brass with casted swinging spout complete all as specified and as directed by the Engineer-in-Charge |
| 32 | S&F in repair 15mm bore cast copper alloy chromium plated fancy type wall mixture with telephonic shower arrangement with pipe bend (three in one) etc complete all as specified and as directed by the Engineer-in-Charge |
| 33 | S & F in repairs, PVC (SWR) 75 mm dia, floor trap, plain with grating including jointing to waste pipe with solvent cement complete all as specified and as directed. |
| 34 | Dismantling any bore, cast iron or reinforced concrete or PVC pipes for rain water ,drain pipes, jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.. |
| 35 | S & F in repair PVC (SWR) Pipe 110mm bore , single socketed, in any length with rubber ring joints fixed to wall with MS clamp mad of angle iron 50x5 mm and suitable size of bolt nut and set of washer etc complete all as specified and directed. |
| 36 | S & F in repair PVC (SWR) Bend any radius 110 mm bore etc complete all as specified and directed. |
| 37 | M&L for Cutting chases , pinning in making good to facing for concealed water tubing n.exc. 10 cm girth and making good with (1:3) cement mortar complete all as specified and directed. |
| 38 | Dismantling floor/hearth or wall tiling including cement mortor bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 39 | M&L, for PCC 1:2:4 type B-0 using 12.5 mm gradesd stone agg as in levelling course of floors of 25 mm thick complete all as specified and directed. |
| 40 | M&L, coloured non skid dark/light ceramic tile 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.36 sqm but not exceeding 1.00 sqm, in floor etc set and jointed in neat Cement slurry and pointed in coloured cement to match including screed bed or bedding layer in CM 1:6, 15mm thick complete all as specified and directed. |
| 41 | M&L, coloured non skid dark/light ceramic tile 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floor etc set and jointed in neat Cement slurry and pointed in coloured cement to match including screed bed or bedding layer in CM 1:6, 15mm thick complete all as specified and directed. |
| 42 | M&L, coloured non skid dark/light ceramic tile 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat Cement slurry and pointed in coloured cement to match including screed bed or bedding layer in CM 1:6, 15mm thick complete all as specified and directed. |
| 43 | M&L for ceramic coloured tiles 7 to 8 mm thick (square / rectangular) joint free , area of each tile exc 0.36 sqm but n. exc 1.00 sqm, on vertical surfaces of wall etc over 10 mm thick rendering in CM 1: 4 set and jointed in neat Cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified and directed |
| 44 | M&L for ceramic coloured tiles 7 to 8 mm thick (square / rectangular) joint free , area of each tile exc 0.18 sqm but n. exc 0.36 sqm, on vertical surfaces of wall etc over 10 mm thick rendering in CM 1: 4 set and jointed in neat Cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified and directed |
| 45 | M&L for ceramic coloured tiles 7 to 8 mm thick (square / rectangular) joint free , area of each tile exc 0.11 sqm but n. exc 0.18 sqm, on vertical surfaces of wall etc over 10 mm thick rendering in CM 1: 4 set and jointed in neat Cement slurry and pointed in coloured cement to match the shade of tiles complete all as specified and directed |
| 46 | M&L for glazed ceramic tiles coloured in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles over and including 10mm thick rendering in cement moratar 1:4 complete all as specified and directed. |
| 47 | Demolition of cement concrete (unreinforced) in ground floors and paving n. exc 15 cm thickness below or above ground level including disposal of debris and rubbish to low level area/500 mtr from site complete complete all as specified and as directed. |
| 48 | M&L 60 mm thick machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement & no pigment including PCC 1:2:4, B0 using 12.5mm graded stone aggregate in all edges of interlocking complete all as specified and directed by the Engr-in-Charge. |
| 49 | M&L Coloured rubber moulded in any format 60 mm thick machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey/white cement & pigment including PCC 1:2:4, B0 using 12.5mm graded stone aggregate in all edges of interlocking complete all as specified and directed by the Engr-in-Charge. |
| 50 | M&L, sand cushioing to under concrete interlocking paver block including watering & consolidation complete all as specified |
| 51 | M&L PCC 1:4:8 type D2 using 40mm graded stone agg as in filling and mass concrete, Sub base/flooring complete all as specified and directed. |
| 52 | M&L for 75mm thick cement concrete type C-1, 1:3:6 (20mm graded aggregate) as in plinth protection finished even and smooth without using extra cement all as directed by the Engr-in-Charge. |
| 53 | M&L for 40mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in flooring finished even and smooth without using extra cement complete all as specified |
| 54 | M&L ,Cement concrete 1:3:6 type C1 using 20mm graded stone aggregrate as in surface channels and drains/Soucer drain inclduing demolation of existing PCC in drain etc complete all as specified and directed by Engr-in-Charge. |
| 55 | Supply and fix in repair vitreous china wash basin white flat back size 630x450mm including cutting for and pinning in ends of brackets or erecting stand,waste coupling,32 mm bore PVC waste pipe of suitable length, and connection complete all as directed complete all as specified and as directed. |
