Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Civil Works : BUILDINGS |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating ea deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 5 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300mm apart including drilling 12mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos E.C. 20% with 1% concentration |
| 6 | Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III)derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 8 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 9 | Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of garde M-25 of specified diameter and length below pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by Crawler mounted, telescopic boom hydraulic pilling Rig all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note: Truck Mounted rotary/TMR/Tube well boring machine shall not be used. 600 mm dia piles |
| 10 | Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. Single pile above 50 tonne and upto 100 tonne Safe capacity. Routine test (Test Load 1.5 times the Safe capacity) |
| 11 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 12 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth and upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 17 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 18 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 19 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 20 | Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm/230mm/300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 21 | Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. |
| 22 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 23 | Brickwork with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 24 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. |
| 25 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm |
| 26 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI- 212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm. |
| 27 | 20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) |
| 28 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand) |
| 29 | 12 mm cement plaster of mix: 1:4 (1 cement: 4 coarse sand) |
| 30 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 31 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 32 | Finishing wall with textured exterior paint of required shade: New work (Two or more coat applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 33 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats |
| 34 | Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 35 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 36 | Finishing with Delux Multi surface paint system for interior and exterior using primer as per manufacturers specification: Painting wood work with Delux Multi Surface paint of required shade. Two or more coat applied @0.90ltr/ 10sqm over an under cost of primer applied @ 0.75ltr/10sqm of approved brand and manufacture |
| 37 | Bick work with common burnt clay machine moduled modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10mm wide 12mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). Above plinth level upto floor V level |
| 38 | Providing and fixing of façade at all heights with extruded hollow Clay / Terracotta ventilated rainscreen tiles of height 250/ 300/ 400mm and length of 595 mm of approved texture,design and pattern having Flexural Strength/ Modulus of Rupture of > 14 N/m² and maximum water absorption of 10% tested as per ISO 10545-4:2004(E) and ISO 10545-3:1995respectively in true level fixed to a supporting aluminium framework (Alloy 6063 T5/T6) consisting of vertical 'T' (for intermediates)/ 'L'(for ends/ termination)/ Tubular sections (at corners)of size 80x60x2mm/ 40x60x2mm/ 40x40x2mm respectively, spaced at maximum spacing of 600mm c/c matching to the tile vertical grid, and horizontal aluminium 'C'-clamps of size 56x25x2mm thickness of length 150mm at junction of tiles and of length 75mm at wall ends/ corners fixed on top of the vertical sections at spacing of 250/ 300/ 400mm c/c matching to the tile horizontal grid with two numbers of selfdrilling/ self-tapping SS screws of size 5.5x25 mm with EPDM washers.The vertical 'T'/'L/ Tubular' sections shall be fixed to the wall using HDG (hot-dip-galvanized) steel L-brackets galvanizing thickness of minimum 80 microns)of size 110x80x6 mm at intermediate vertical aluminium profiles and of size 220x110x12 mm at outer corners and stainless steel grade 304, M10 full threaded anchor fasteners with nylon sleeve100mm long (for brick work) and M8 expansion anchor fasteners 75mm long for concrete surface, spacing of brackets to be based on a structural/ static calculation. The brackets shall be of length 175mm at junction of two vertical aluminium profiles and of length 100mm at intermediate points of vertical profiles and shall be fixed to the vertical aluminium T / L / Tubular profiles using two numbers self-drilling/ self-tapping SS screws of size 5.5x25mm with EPDM washers. EPDM gaskets to be fixed in between brackets and vertical profiles. The tiles shall be mounted on the ‘C’ clamps such that the tiles are supported at top and bottom at both ends. The tiles shall be additionally secured to the horizontal ‘C’ clamps using special SS clips of required size which shall be inserted and pressed into position on the ‘C’ clamps holding the tiles and the cuttiles shall be glued at points to the horizontal ‘C’ clamps by using MS Polymer sealant adhesive. The vertical joint open groove between two adjacent tiles shall be 5mm. The tiles and system shall be designed to resist wind load as per IS 875 (Part 3) according to different zones. The tiles shall be installed using the ventilated rain screen principle with provision for natural ventilation of the space between the façade tiles and the structural wall. The work shall be carried out as per specification, drawing and as per direction of the Engineer-in- Charge. Note : Scaffolding wherever required to be paid separately. With 16mm thickness (+/- 10%) terracotta tiles of grey colour |
| 39 | Providing and laying Polished Granite stone flooring and tread of steps in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 40 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size. Size of Tile 600 x 1200 mm |
| 41 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 42 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 43 | Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 44 | Providing & Fixing Providing and Fixing horizontal level suspended metal ceilings comprising of Knauf or other approved make Metalworks V-P 500 Hook-on baffle system manufactured by Knauf Ceiling Solutions with Rectangular vertical baffle blades made of Aluminium (Grade AA 3105, H14 temper) in coated thickness of 0.7mm ± 0.05mm as per IS:2676 (1981), pre-coated to Wood Grain shade, suitable for architectural finishes and Interior applications, with single grid system and suitable spacing between baffles. The baffle width shall be 50mm, height shall be 150mm, length shall be ranging from 600mm to 3000mm. The on-center spacing of baffles shall be 150mm (clear space between baffles 100mm). The baffles shall have plain unperforated finish with square edge, hook-on edges with suitable upturns. The baffle shall be manufactured using pre-painted coil made of super durable polyester (SDP) Paint OR Polyester (PE) Paint. The rear surfaces shall be coated with Polyester (PE) of thickness 10±2 μ (bottom coat), while the front surface shall be coated with SDP OR PE comprising of base coat of 15-16 μ, and clear coat of 10-12 μ, forming a top coat of DFT 25±5 μ (as per ASTM D 7091). The pre-painting shall pass Salt Spray Test for 2000 Hours (as per ASTM B117), Humidity test for 2000hours (as per ASTM D1735). The pre-painting shall have an pencil hardness F-H (as per ASTM 3363), scratch resistance >1500gm (as per BS 3900 Part E2), solvent resistance MEK >100 DR (as per ASTM D 5402), flexibility test 2T Pass (as per ASTM D 4145), adhesion test with No Tape off (as per ASTM D 3359), reverse impact resistance with No Peel off (as per ASTM D 2794). The shade variation across batches shall be delta E<1 using Excite/BYK Gardner instrument and gloss level of 25±5 GU at 60˚ as per ASTM D523. The grids shall comprise primary U-shaped slotted carrier bars of 120gsm galvanised steel (GI) of 3000mm L x 43mm H x 30mm W x 1.5mm T. Accessories shall include baffle connector (GI), baffle face cover (GI) – Wood Grain shade, carrier bar splice (GI), carrier spring (SS), wall anchor (GI). of approved make as per instructions of EIC. |
| 45 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams / sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 46 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams / sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting / making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. |
| 47 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm ea having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge Gypsum moisture resistant board |
| 48 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position withhold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood |
| 49 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) decorative type, core of block board construction with frame of1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 50 | Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately) |
| 51 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm |
| 52 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 53 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 125 mm |
| 54 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being Termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 30MM THICK |
| 55 | Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately). |
| 56 | Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paidfor separately). |
| 57 | Providing and fixing factory made uPVC glazed/ wire mesh windows/ doors comprising of lead free uPVC multi- chambered frame, sash and mullion/ coupler (wherever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced withgalvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor(whereever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia. with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/ mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (iii) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (iv) Sites with structure height more than 20m for all wind speeds. Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R4 series with frame (64mm & above) x (45mm & above) & sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi- point locking system (Height above 1.8m). |
| 58 | Providing and fixing factory made uPVC glazed/ wire mesh windows/ doors comprising of lead free uPVC multi- chambered frame, sash and mullion/ coupler (wherever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (whereever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia. with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/ mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/ without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (iii) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (iv) Sites with structure height more than 20m for all wind speeds. Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R4 series with frame (115mm & above) x (45mm & above) & sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on two end panels along with multi-point locking system. (Height above 1.8 meter). |
| 59 | Providing and fixing factory made uPVC glazed/ wire mesh windows/ doors comprising of lead free uPVC multi- chambered frame, sash and mullion/ coupler (wherever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (whereever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia. with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/ mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh/ Glazing of plain/ toughened/ laminated/ double glass unit with/ without highperformance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (iii) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 (iv) Sites with structure height more than 20m for all wind speeds. Fixed window/ ventilator with mullion/ transom. Using R1 series withframe (33mm & above) x (35mm & above) & mullion (33mm & above) x (50mm & above). (Height upto 0.90 meter) |
| 60 | Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. complete. |
| 61 | Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete. |
| 62 | Float glass panes: 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm). |
| 63 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than12.50 kg/sqm) |
| 64 | Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete : 125x64x2.50 mm |
| 65 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm |
| 66 | Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125mm |
| 67 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 68 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 69 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 70 | Providing wood work in frames of false ceiling ,partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Kiln seasoned and chemically treated hollock wood |
| 71 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured).Panelling for panelled or panelled and glazed shutters 25mm to 40 mm thick : Ply wood 7 ply, 9 mm thick: Decorative plywood one side decorative veneer and commercial veneer onother face (Type 1) conforming to IS 1328 BWR Type |
| 72 | Providing and fixing in position factory made non asbestos fibre reinforced aerated cement sandwich wall/roof/floor light weight solid core panels made of light weight cement concrete core composed of OPC cement, pulverized flyash, quick lime, cotton pulp & Gypsum in mortar state mixed with aeration agent in a preset mould. The outer face on both sides of the panels will be non asbestos fibre cement board confirming to IS 14862:2000. These solid wall panels are installed using Galvanized iron steel tracks/C channel of 1mm thick of required sizes as recommended by manufacturer's and fixed to floor and RCC soffit in plumb to ea other with steel screw/ fasteners. The panel shall be fixed vertically with tongue & groove joint with cement based polymer modified jointing compound. The exposed surface finished with fibre mesh/glass fibre tape with polymer based jointing compound having superior flexibility. Panels should be used as floor & roofing with additional structural support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturers specifications and under the overall direction of Engineer-in-Charge (Cost of all the material is included except \\"tracks/C channel\\" which will be paid separately). Non load bearing panels 75 mm thick of required size (minimum 5mm thick fibre cement board Type A, Category IV as per IS: 14862:2000 on both faces) |
| 73 | Providing and fixing bolts including nuts and washer complete |
| 74 | \\"C\\" Chanel Frameing Work for cement sandwich wall |
| 75 | Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately) |
| 76 | Providing & Fixing Knauf / Armstrong or other approved make OPTRA Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut, Shell, Warm Lavender, Pea, Carnation Pink, Cinnamon, Aurelion, Moonstone Blue, Industry Grey, Fern Green, Zest, Winter Hazel, Dark Olive, Pearl, Pastel Purple, Dust Storm, Tan, Cyber Grape). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600 x 600 x 25mm, 600 x 1200 x 25mm, 600 x 1800 x 25mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass substrate shall have a recycle content of 85%. |
| 77 | Providing & Fixing Knauf / Armstrong or other approved make Channelled Woodworks perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 21mm of visible pane. The edges of the panel shall be “tongue-and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.5. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm.The panels shall be mounted on special aluminium splines (keel) using inside clips provided by Knauf and approved by the Architect/ Engineer-in-Charge. |
| 78 | Fabric: Sabine- Construction 100% Polyester, Both Side Acrylic coating, Fabric Thickness 0.6 MM, Fabric Weight +-5% 308 GSM, Wrap 2/60 Weft 2/8. Hardware Details: Head Rail: Head rail is of 25mm high and 47 mm wide extruded High strength aluminum alloy section with average wall thickness of minimum 0.9mm. The section is anodized for smooth operations and has the provision of fabric valance matching with louvers fabric. End Control Unit (Reduction Gear Box): End control unit state of art reduction gear box having the reduction ratio of 3.5:1 for a very smooth operation of the blind. This unit consists of a planetary gear in the outer housing, four small transmission gears fitted in the middle assembly and an end receiving gear attached to central sprocket unit. Tilt Rod: It is made of extruded aluminum having three keyways. The tilt rod is fixed in the end control unit and drives the carrier gear mechanism to rotate the louvers. The average diameter is 5.8mm to achieve minimum torsion deflection. Tilter Chain: This is made of 4.5 mm plastic beads molded on 1.5 mm thick polyester cord. The Pitch of the beads is 6mm. The chain drives the sprocket fixed in the end control unit to rotate the louvers by 180 degrees. The pitch of the chain corresponds to the sprocket in perfect match for trouble free operation. It is provided in white color. Carrier (Runner): This is a molded component having anti friction additive. It consists of polymer housing with wheels mounted on sides and has a gear and worm mechanism with vertical worm fixed with a tongued poly carbonate stem to hold the louvers. The worm and gear mechanism are driven by tilt rod fixed to end control unit to rotate louvers by 180 degrees. The mounted wheels on sides of casing move on rails of head rail section for resistance free stacking of louvers Spacer: This is made of molded High Polymer ABS, having anti friction additive. It maintains proper spacing of the runners and ensures overlapping of louvers for perfect light control. It is available in 100mm size. Installation Bracket: This is made of galvanized steel “L” bracket of thickness 3mm which is fitted with pressure clip made of spring steel to hold the head-rail. Cord Weight: This is made of ABS material hollow casing with a steel weight inside. Cord: It is 2.2mm in diameter, Nylon braided high strength cord having maximum abrasion resistance & minimum elongation. Bottom Mechanism (Weight and Chain): The purpose of this is to keep the louver straight & prevent them from swaying. Preferred Make- VISTA, HUNTER DOUGLAS, D-DECORE |
| 79 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover |
| 80 | Providing and fixing ball bearing for rolling shutters. |
| 81 | 8 Passenger elevator with 5 stops without machine room as per specification - 282 MonoSpace R25.1-1 of preferred make KONE / JOHNSON / OTIS / SCHINDLER / MITSUBISHI ELECTRIC / Thyssenkrupp / HITACHI |
| 82 | Providing & fixing Century or other approved make - Brillo-BU cubicle self-supporting 18mm thick compact laminates, manufactured through high pressure and temperature processes in accordance with EN 438- Part 4 standards. The panel's core comprises a specified number of Kraft papers impregnated with thermosetting phenolic resin, while the decorative layer is impregnated with thermosetting Melamine resin. These panels offer exceptional resistance to scratches, abrasions, heat, cigarette burns, chemicals, impacts, graffiti, and moisture, as well as possessing anti-bacterial properties.This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304/316 ) as per manufacturer’s specifications & Architects instructions like (1) Door Knob (2) Spring Loaded Hinges (3) Thumbturn lockset with occupancy indicators (4) Coat hook (5) U-Channels (6) Shoe Box (7) Floor Anchor (8) Rubber noise deafening tape (9) Screws & wall Plugs.The top fitting should consists of brush type finish rectangular box type toprail which will get fixed with pilasters.All screws will of 304 Grade in stainless steel . All pilasters are supported by stainless steel shoe box. The base of the stainless steel shoe box will be anchored to the floor with a clearance height upto 100mm or equivalent |
| 83 | Providing & fixing Century or other approved make - Urinal Modesty Panel ( UMP ) self-supporting 12mm thick compact laminates, manufactured through high pressure and temperature processes in accordance with EN 438- Part 4 standards. The panel's core comprises a specified number of Kraft papers impregnated with thermosetting phenolic resin, while the decorative layer is impregnated with thermosetting Melamine resin. These panels offer exceptional resistance to scratches, abrasions, heat, cigarette burns, chemicals, impacts, graffiti, and moisture, as well as possessing anti-bacterial properties.This also includes providing and fixing in position necessary hardware made out of hardwares as per manufacturer’s specifications & Architects instructions like (1) L bracket (2) Screws & wall Plugs ( SS- 304 ) as per the instruction of EIC. |
| 84 | Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge. |
| 85 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in -charge.: Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 86 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.:In cement mortar |
| 87 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 88 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below |
| 89 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 90 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: Asbestos Cement sheet |
| 91 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 92 | Carriage of Materials by mechanical transport including loading, unloading and stacking :Bricks : 5 Km |
| 93 | Carriage of Materials by mechanical transport including loading, unloading and stacking : Lime, moorum, building rubbish : 5 Km |
| 94 | Carriage of Materials by mechanical transport including loading, unloading and stacking : Tmber : 5 Km |
| 95 | Carriage of Materials by mechanical transport including loading, unloading and stacking : Steel : 5 Km |
| 96 | Carriage of Materials by mechanical transport including loading, unloading and stacking : Cement, stone blocks, G.I.. C.I., A.C., & C.C. pipes below 100 mm dia and other heavy materials |
| 97 | CIVIL WORKS : Gangway/Skywalk |
| 98 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soil |
| 99 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating ea deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 100 | Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. |
| 101 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6(1Cement : 3coarse sand (zone-III) derived from natural sources :6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 102 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting ofconcrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimumspecified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specifiedm minimum cement content, the contractor shall have discretion to either re- design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 103 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete |
| 104 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 105 | Structural steel work in single section, fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 106 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 107 | Applying priming coat. With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 108 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 109 | The 900 GSM PVC Coated Tensile Fabric is designed for various applications, including outdoor shelters, event tents, and tarpaulins. It is known for its weather proof protection and resistance to water and UV rays - For skywalk. |
| 110 | The 900 GSM PVC Coated Tensile Fabric is designed for various applications, including outdoor shelters, event tents, and tarpaulins. It is known for its weather proof protection and resistance to water and UV rays - For parking. |
| 111 | Modular Furniture |
| 112 | Enterprise or equivalent 1500 Table with CPU Hanger size shall be 1500 Width mm x 750 Depth mm x 728 Height mm . Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) . |
| 113 | Bravo or Equivalent MB chair: SeaT/BACK ASSEMBLY: The seat and back are made up of 1.2 ±0.1cm. thick hot-pressed plywood measured. upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area.MID BACK SIZE 47.5 cm. (W) x 58.0 cm. (H). SeaT SIZE 47.0 cm. (W) x 48.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.ARMRESTS: The one-piece armrests are injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO MECHANISM : The mechanism is designed with the following features: ·360° revolving type. · Upight position locking · Tilt tension adjustmen. ·Seat/back tilting ratio of1:3.TUBULAR FRAME : The powder coated ( DFT 40-60 microns ) tubular frame is cantilever type & made of Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube.PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLY : The bellow is 3-piece telescopic type and injection moulded in black Polypropylene.PEDESTAL ASSEMBLY : The pedestal is injection moulded in black 33%glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-centre dia. (76.3 ±1.0cm with castors).TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.Overall Dimensions of ChairWIDTH (W): 76.3 CM.DEPTH (D): 76.3 CM.HEIGHT (H): 85.5-97.5 CM.SEAT HEIGHT (SH): 42.5-54.5 CM. |
| 114 | Arrive or equivalent Desk: The Main table shall be of size 3600 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in Smart Case - space slides effortlessly in style.The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm x 600 Height mm. Mobile pedestal shall be coated of MDF (medium density fiber ) with veneer coating and PU coating.The ERU Top shall be of MDF (medium density fiber) board duly finished with veneer and final PU coating. Size of ERU top 1900 Width mm x 480 Depth mm x 550(not from ground with castors).The main desk is provided eith the wire management system also there is perfect storage side unit . |
| 115 | Arrive or equivalent Back Unit: The Size of the Back unit shall be 1000 mm width x 480 mm Depth x 2035 mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. The mobile unit can be bought in multiples.PU coating hardness 1.5H. |
| 116 | La Sede or equivalent HB Chair : SeaT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D). BACK SIZE : 47.5 cm. (W) x 77 cm. (D)ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features: • 360° revolving type.• Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.• Tilt tension adjustment can be operated in seating position.• 5-position Tilt limiter giving option of variable tilt angle to the chair.• Seat/back tilting ratio of 1: 2.• The mechanism housing should be made up of HPDC Aluminium black powder coated. SeaT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm.PEDESTAL ASSEMBLY The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.). TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Polypropylene. Overall Dimensions of Chair Seat Height -44.5 to 54.5 cm. Height -114.0-131.5 cm. Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm |
| 117 | La sede or equivalent visitor chair: SeaT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D). BACK SIZE : 46.5 cm. (W) x 59.5 cm. (D)ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. PEDESTAL ASSEMBLY The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.). VISITOR TUBULAR FRAME: The tubular frame is cantilever type and made of 02.54±0.03 X 0.2±0.016 cm thk S.S 202 tube. The back connected to frame through chrome plated high pressure die cast connector piece. Overall Dimensions of Chair - Seat Height -46.2 cm. Height -98.2 cm. Width-60.9 cm and Depth-64.7 cm |
| 118 | Bayflow or equivalent 3 seater sofa: Dimensions W x H x D (cm) - 202 x 97.5 x 89. Primary Material - Leatherette. Upholstery Material - Synthetic Leather. Seat Height (cm) - 45.5 |
| 119 | Bayflow or equivalent single seater sofa: Dimensions W x H x D (cm) - 97 x 97.5 x 89. Primary Material - Leatherette. Upholstery Material - Synthetic Leather. Seat Height (cm) - 45.5 |
| 120 | Meraki or equivalent coffee table: Overall Size : Width : 120cm Depth : 60cm Height : 36.7cm Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Drawer bottom is made of .9 mm thick prelaminated particle board .Drawer front is made of 18 mm thick PU painted MDF . Legs : Rubber wood . Hardware : Hettich . Construction : Knock down .Finish : All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets : 1 nos . Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness. Hardware : Hettich . Construction : Knock down .Finish : • All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band . PU lamination is high gloss in Ecru shade .Packets : 1 nos |
| 121 | Meraki or equivalent corner table: Overall Size : Width : 60cm Depth : 60cm Height : 49.8cm Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Drawer bottom is made of .9 mm thick prelaminated particle board .Drawer front is made of 18 mm thick PU painted MDF . Legs : Rubber wood . Hardware : Hettich . Construction : Knock down .Finish : All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets : 1 nos . Materials : All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness.Hardware : Hettich . Construction : Knock down .Finish : • All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band . PU lamination is high gloss in Ecru shade .Packets : 1 nos |
| 122 | Meraki or equivalent TV/Media Unit: Overall Size : Width : 180.4cm Depth : 49.5cm Height : 50.4cmMaterial :All carcass panel are made of 18 mm prelaminated particle board with edge banding 1.5 mm thickness. Drawer bottom is made of .9 mm thick prelaminated particle board. Drawer front is made of 18 mm thick PU painted MDF. Middle doors are made of 4mm thick toughened glass with PU paint in black .All drawers are fitted with knobs. Legs : Rubber wood Hardware : Hettich .Construction : Knock down .Finish : All 18 mm prelaminated particle board panels are Noce Versaillies with walnut edge band. PU lamination is high gloss in Ecru shade .Packets : 2 nos |
| 123 | Mingle or equivalent Unitized Conference table 10 seater: Supplying and placing in position conference table of the following specifications with following size shall be 2 STR MAIN - 1350 X 600 X 740. Qty - 22 STR END_LH - 1350 X 600 X 740. Qty - 12 STR END_RH - 1350 X 600 X 740. Qty - 11 STR SHARED - 675 X 600 X 740. Qty - 21800 Head. Qty - 1Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes.Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns).Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop. |
| 124 | Marvel or equivalent Mid Back chair: SeaT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D). MID BACK SIZE: 47.7 cm. (W) x 60.1 cm. (D). ARMRESTS : The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM : The adjustable tilting mechanism should be designed with the following features: • 360' revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminium black powder coated. SeaT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm.ADJUSTABLE BACK SUPPORT : Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT : The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. Overall Dimensions of Chair. Seat Height -43.1-53.1cm. Height -96.5-114.0.cm. Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm |
| 125 | Marvel or equivalent HB Chair: SeaT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D). HIGH BACK SIZE: 47.7 cm. (W) x 76.4 cm. ARMRESTS : The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM : The adjustable tilting mechanism should be designed with the following features: • 360' revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminium black powder coated. SeaT DEPTH ADJUSTMENT : Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. Overall Dimensions of Chair - Seat Height -43.1-53.1cm. Height -112.7-130.2cm. Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm |
| 126 | Mayfair or equivalent Main Desk+Mayfair ERU+Mayfair Pedestal: Mayfair Main Desk size shall be 1350 Width x 750 Depth x 750 Height.The Top shall be in white cedar and black and shall be 18 mm PLB with PVC lipping.The side panels shall be 18 mm thickPLT with PVC .The Modesty panel shall be 18 mm thick PLT.The Modesty panel shall be in a combination of black & white cedar. Mayfair ERU size shall be 1200 Width x 450 Depth x 750 Height.The top of ERU shall be 18 mm thick PLT with PVC lipping.The feature of ERU shall be thait is common for both LHS nd RHS. The colour of ERU top shall be white cedar , side panels shall be in black and the Modesty panel shall be a combination of black & white colour. Mayfair Pedestal size shall be 390 Width x 435 Depth x 529 Height.The top is 18 mm thick PLB . The two drawer mobile pedestal is available in one size .The top and drawer fronts shall be in white cedar while the other components shall be in black. |
| 127 | Marvel or equivalent Visitor Chair: SeaT /BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D). BACK SIZE: 47.7 cm. (W) x 60.1 cm. (D). Visitor TUBULAR FRAME: The tubular frame should be cantilever type and made of Ø2.54± 0.03 cm X 0.02 ± 0.016cm thick SS 202 tube. The back should be connected to frame through chrome plated high pressure die case connector piece. Overall Dimensions of Chair - Seat Height -44.8cm. Height -98.2cm. Width & Depth of Chair as measured from base - Width-60.9 cm and Depth-64.2 cm |
| 128 | Godrej or Equivalent Modular Workstation Wish Recta: * PROVIDING AND PLACING 52.4MM THICK 1200 MM HIGH PANELS ALONG SPINE IN WISH SYSTEM. WITH COMBINATION OF METAL RACEWAY AT BOTTOM, TWO INTERMEDIATE FABRIC BLOCKS, TOP TILE - FABRIC TACKABLE, WHITE BOARD. PROVIDING POWDER COATED LEGS. PROVIDING 22.8 MM THICK PANEL WITH BOTTOM METAL SCREEN, INTERMEDIATE FABRIC SCREENS & TOP SCREEN IN FABRIC MAGNETIC FINISH including Mobile pedestal, KBPT & CPU Trolley. Dimension of penta: 1200 mm W X 600 mm D as approved by EIC. |
| 129 | Greta or eqvivalent Full Back Revolving chair: SeaT ASSEMBLY: The seat is made up of 1.5 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and moulded polyurethane foam. SeaT SIZE: 51.8cm (W) x 49.7cm (D). BACK ASSEMBLY: The Back is injection moulded in glass filled Nylon which is upholstered with Mesh fabric.The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropylene and can be adjusted to 6.0±0.1cm height. It also has swivel and To and Fro adjustment with moulded PU armtop. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features:· 360° revolving type, Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort. Tilt tension adjustment can be operated in seating position. 5 position Tilt limiter giving option of variable tilt angle to the chair. Seat / back tilting ratio of 1:2. The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron). It has an adjustment of 3.0 ± 0.1cm & it is assembled over GRETA 2.0 Full back chair. The complete headrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is Ø66.1 ± 0.5 cm.(76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Polyamide having 6.0± 0.1cm wheel Diameter. |
| 130 | Godrej or Equivalent Modular Workstation Wish Penta: * PROVIDING AND PLACING 52.4MM THICK 1200 MM HIGH PANELS ALONG SPINE IN WISH SYSTEM. WITH COMBINATION OF METAL RACEWAY AT BOTTOM, TWO INTERMEDIATE FABRIC BLOCKS, TOP TILE - FABRIC TACKABLE, WHITE BOARD. PROVIDING POWDER COATED LEGS. PROVIDING 22.8 MM THICK PANEL WITH BOTTOM METAL SCREEN, INTERMEDIATE FABRIC SCREENS & TOP SCREEN IN FABRIC MAGNETIC FINISH including Mobile pedestal, KBPT & CPU Trolley. Dimension of penta: 1350 mm W1 X 1350 mm W2 X 600 mm D1 X 450 mm D2 as approved by EIC. |
| 131 | Traverse or equivalent 3 seater with cushion: SeaT/BACK SHELL: It is powder-coated shell made from cold rolled M.S. sheet 0.12 ± 0.013 cm thickness with circular perforations.The Side Bar is made of cold rolled M.S.sheet 0.12 ± 0.013 cm thickness. The Shell is assembled on the Cross Beam with help of M8 Bolts.SeaT SIZE : 50.0 cm (W) x 45.5 cm (D) BACK SIZE : 50.0 cm (W) x 56.0 cm (H)CROSS BeaM: It is made up of cold rolled steel with 0.2 ± 0.02 cm thickness. The crossbeam is powder coated. It is covered with plastic end capsLEG: It is made up of cold rolled steel with 0.12 ± 0.013 cm thickness. It is powder coated. The legs are fitted with leveller cups covered with SS304 sheet. ARMREST: It is made of SS304 round tube of Ø 3.175 ± 0.03cm x 0.12 ± 0.013 cm thick formed to make an oblong shape.WIDTH (W): 173.5 CM.DEPTH (D): 74.0 CM. |
| 132 | Pisa or equivalent 3 seater sofa: SeaT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 206.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM. |
| 133 | Pisa or equivalent single seater sofa: SeaT FOAM : The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for cushioning purpose. LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. Width (W): 86.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM. |
| 134 | Pisa or equivalent Corner Table: PISA SIDE TABLE GLASS: It is 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. PISA SIDE TABLE UNDERSTRUCTURE: It is a welded Assembly made in SS202 grade Dia. 12±0.04 as per IS:1762. Width of table= 60.0 cm, Depth=60.0 cm, height=34.9 cm. |
| 135 | Wish or equivalent Cubicle: * PROVIDING AND FIXING 52.4MM THICK 1200 MM HIGH PANELS IN WISH SYSTEM. WITH COMBINATION OF METAL RACEWAY AT BOTTOM, TWO INTERMEDIATE FABRIC BLOCKS, FABRIC TACKABLE, WHITE BOARD, FABRIC MAGNETIC AT TOP. PROVIDING POWDER COATED LEGS..* PROVIDING POWDER COATED FRONTIER LEGS & PRELAM MODESTY. Main Table Dimension 1500 mm X 600 mm. ERU 900 mm X 450 mm. Mobile Pedestal, KBPT, CPU Trolley. |
| 136 | Greta or equivalent Full Back Revolving chair: SeaT ASSEMBLY: The seat is made up of 1.5 ± 0.1 cm thick hot - pressed plywood upholstered with fabric and moulded polyurethane foam. SeaT SIZE: 51.8cm (W) x 49.7cm (D). BACK ASSEMBLY: The Back is injection moulded in glass filled Nylon which is upholstered with Mesh fabric.The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 ±0.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE) :The height adjustable armrest is made of Polypropylene and can be adjusted to 6.0±0.1cm height. It also has swivel and To and Fro adjustment with moulded PU armtop. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features:· 360° revolving type, Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort. Tilt tension adjustment can be operated in seating position. 5 position Tilt limiter giving option of variable tilt angle to the chair. Seat / back tilting ratio of 1:2. The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron). It has an adjustment of 3.0 ± 0.1cm & it is assembled over GRETA 2.0 Full back chair. The complete headrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0 ± 0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is Ø66.1 ± 0.5 cm.(76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in black Polyamide having 6.0± 0.1cm wheel Diameter. HeaDREST: The Headrest sub-assembly is made up of injection moulded glass filled Polypropylene which is upholstered with moulded HR polyurethane foam and fabric. It has an adjustment of 3.0 ± 0.1cm & it is assembled over GRETA 2.0 Full back chair. The complete headrest assembly is retro fit to the main chair |
| 137 | Relax or equivalent 4 legs with arm; without castor: SeaT / BACK ASSEMBLY : The Seat is injection moulded in glass filled Polypropylene compound which is upholstered with fabric upholstery covers and moulded Polyurethane foam. The Back is injection moulded in glass filled Polypropylene compound which is upholstered with Mesh fabric (Refer colour chart for seat & Back upholestry in product catalog).* SeaT SIZE : 50.0cm. (W) x 48.0 cm. (D).* BACK SIZE : 53.0 cm. (W) x 39.0cm. (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25% compression. M.S. POWDER COATED FRAMES FOR 4 LEG CHAIRS :The powder coated ( DFT 50±10 microns) welded tubular main frame is made from Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm and Ø1.6±0.3mm x 0.16 ± 0.0128cm M.S. E.R.W tube. The Ø1.9 ±0.3mm x 0.12 ±0.0096 cm M.S.E.R.W. tube used as connecting member between LH & RH frames. M.S. POWDER COATED FRAMES FOR SLED BASE CHAIRS : The powder coated( DFT 50±10 microns) welded tubular main frame is made from Ø 2.54 ± 0.03 cm x 0.2 ± 0.016 cm and Ø1.9 ±0.3mm x 0.12 ±0.0096 cm M.S.E.R.W. tube. SHOE : The shoes are made of glass filled Polypropylene compound with and pressed fitted with tubular frame. Felt is provided below the shoes. ARMREST : The Armrest are made of glass filled Polypropylene compound and assembled over the tubular frame. |
| 138 | Thrill or equivalent LC HB Chair: SeaT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area. The chair seat & back size are HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H). SeaT SIZE 53.5 cm. (W) x 51.0 cm. (D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The adjustable armrest is designed with the following features · Up- Down adjustment– 6 steps (7.2 ± 0.5cm range). · Armrest top is mounted on Armrest structure made of glass filled Nylon. · Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: 360° revolving type.· 3 position locking with anti shock mechanism. Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 113.5-123.5 CM. SeaT HEIGHT (SH): 46.0-56.0 CM. |
| 139 | Thrill or equivalent LC Visitor Chair: THRILL CHAIR UPPERSTRUCTURE: It is a single shell 1.2 ±0.1cm. thick hot pressed plywood with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and comfort in chair. SeaT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per IS:7888 at 25% compression. M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60 micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted on to a tubular frame. WIDTH (W): 60.5 CM. DEPTH (D): 65.0 CM. HEIGHT (H): 86.5 CM. SeaT HEIGHT (SH): 46.0 CM. |
| 140 | UNITIZED or equivalent T25 TABLE(1500W X 600D X 750H): 1500W X 600D X 750H. 400W X 450D X 640H(pedestal). Main Worktop-Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Return Worktop-Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel-Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Legs-Cube legs are fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) are welded for fixing worktop. These are welded togesther by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members-Cross Members in Unitized T-2 Desk Series are made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These are coated with 50 micron epoxy polyester coating.Cross Members are assembled by friction fit PDC joinery and grub screws. There are always two cross members for one table. Access Flap-Soft closing access flap is used in Unitized T-2 Desk Series. Provision for standard size of 8 module electrical (Anchor Roma) is offered. Access flap is made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power Box-Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision for Anchor Roma). This is fixed with worktop along the depth at Access Flap position. Integrated Hinge Door Storage with Drawer-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Door is fixed with slide on hinges and handle is provided for ease of opening. Drawer is provided with ebco metabox slide and lock for security. |
| 141 | Reflection or equivalent 8 ft L shape desk: Work Surface - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Access Flap along with a Grommet is provided on work surface for wire management. Wire Management - Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma). This is fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting - Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. TOP shelf - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit - Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. **Drawer bottom is made of 5.5thk MDF whiteboard Handle is provided for ease of opening. HDU and Drawer is provided with cam lock for security. Essential Accessories - Wire Riser made of 0.8mm CRCA (IS-513) is provided for proper wire management. Organizer Plate made of 1.2mm CRCA (IS-513) is provided for magnetic sticky notes. Bag Hanger Hook made of 1.2mm CRCA (IS-513) is provided for bag hanging. Length - 2400mm, Depth - 1770mm, Height - 740mm. |
| 142 | Mingle or equivalent Unitized Conference table 8 seater2350 X 1150 X 740.Work top-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Soft closing dual access flap provided for access to power supply and data cables. Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Management- A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for standard 8 module Anchor Roma is provided. Beside ea cutout, an additional cutout with plate is provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc). |
| 143 | Mingle or equivalent Modular Conference table : Supplying and placing in position conference table of the following specifications with following size shall be 2 STR MAIN - 1350 X 600 X 740. Qty - 12 STR END_LH - 1350 X 600 X 740. Qty - 12 STR END_RH - 1350 X 600 X 740. Qty - 12 STR SHARED - 1350 X 600 X 740. Qty - 122350 Head. Qty - 1Work Surface-Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Plastic ABS access flap is provided for easy access to wires and cables. Work top is available in various shapes.Understructure-It consist of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Aluminium alloy 63400 - WP profile is used for connecting panels together. The product has a knock-down construction.Modesty Panel-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated (DFT 40-60 microns).Wire Management-An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pull out audio,video cables onto worktop and connect devices charger to power socket below worktop as per instruction of EIC. |
| 144 | PHE WORKS |
| 145 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 146 | Supply, installation, testing and commissioning of wall mounted type European Water Closet with concealed dual chamber cistern (3 & 6 ltr flush) with flush control plates, flush tank fittings with necessary CI brackets, mounting frame, mounting bolts, WC connector, braided hose connection pipe, seating cover with polythene buffer and flap, flanges, CP bolts & nuts, P-traps, silicon sealant etc. complete including cutting and making good the walls and floors wherever required as per site engineer's instructions. Rack and Bolt shall be free supply of approved make |
| 147 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer-in-charge. |
| 148 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450mm with a pair of 15 mm C.P. brass pillar taps |
| 149 | Providing and fixing in position under counter wash basin with Push botton cock arrangement with 450mm long braided hoses fitted with special CI brackets, aerator, including CP brass waste of standard pattern, complete with accessories like bolts, screws, washers, water supply/ drain connection etc as applicable including making good the walls as per site engineer's instructions Minimum internal diameter of wash basin outlet shall be 32mm All sanitary ware after installation to be protected with proper arrangement till handover of approved make |
| 150 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 151 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 152 | Providing and fixing kitchen sink including making all connections excluding cost of fittings. White glazed fire clay sink of size 600x450x250 mm |
| 153 | Supplying, installing, testing and commissioning of janitor sink with bib tap lever and drainer having 110mm outlets for solid and liquid waste disposal unit with continuous flushing rim and hinged bucket grating, supplied with sound deadening pads and earth tag. (Size as shown in drawing) . Manufactured from grade SS-304 with top quality polish, 1.2 mm thick steel, flush pipe connection upto floor trap with accessories SS legs, connecting pipe, bib tap wall elbows, aerator, cantilever wall brackets, bolts, screws, washers, water supply /drain connection etc as applicable, complete including making good the wall and floors as per site engineer's instructions of approved make. |
| 154 | Supplying and fixing in position geyser of 10 Liter with CP clamps, Connecting hoses, hooks, screws and accessories as needed and the sides of the mirror shall be covered with PVC frame of approved colour etc., in all respect complete. |
| 155 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 156 | Supplying, installing, testing and commissioning of floor mounted plain and cold water cooler of 40 Litres storage made up of food grade stainless steel and taps with all necessary accessories and fittings complete with water supply/ drain pipe connections and making good the walls and floors wherever necessary as per site engineer's instruction of approved make. |
| 157 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 158 | Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 159 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 160 | Providing and fixing brass stop cock of approved quality : 20 mm nominal bore |
| 161 | Providing and fixing brass bib cock of approved quality : 20 mm nominal bore |
| 162 | Providing and fixing toilet paper holder: C.P. brass |
| 163 | Supplying, installing and fixing in position of CP robe hook including accessories like bolts, screws, etc. as applicable, in all respect complete including making good the walls as per site engineer's supervision. |
| 164 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe. 40 mm dia |
| 165 | Supplying, installing and fixing in position of SS Grab bar for toilets 600 mm long made up of stainless steel including accessories like bolts, screws, etc. as applicable, in all respect complete including making good the walls as per site engineer's supervision. Please Enable Macros to View BoQ information |
| 166 | Supplying, installing and fixing in position of SS Grab bar for toilets 600 mm long made up of stainless steel including accessories like bolts, screws, etc. as applicable, in all respect complete including making good the walls as per site engineer's supervision. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
