|
| 1 | Providing and applying tack coat with bitumen VG - 10 grade using bitumen pressure distributor at the rate of .30 kg per sqm on the prepared granular surface treated with primer & cleaned with hydraulic broom as per technical specification |
| 2 | Recycling pavement by cold milling of existing bituminous layers, Using by Bituminous Concrete (Grading-II) using bitumen VG-30 content is 5.4% bitumen weight of mix. For reclaimed material, fresh bitumen will be required to the extent of 60% of normal requirement., planning the surface after cold milling, reclaiming excavated material to the extent of 30% of the required quantity, hauling and stock piling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required, mixing in a hot mix plant, transporting and laying at site and compacting to the required grade, level and thickness, all as MoRT&H specified in clause 519. |
| 3 | S/L Hot applied Thermo Plastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area thick ness of 2.5 mm is exclusive of surface applied glass beads as per IRC 35. the finished surface to be level uniform and free from streak and holes. rates all including of all taxes royality vat etc all t & p /machine material and lobour required for proper complition of work.( SOR 2022 SI.N. 22.02 NEW ITEM ) |
| 4 | Reflective Raised pavement marker providing and fixing of raised pavment markers (cat eye) type x ASTMD - 4956-04 avery dennission /3m (USA make) having moulded body of polycabonate ASA, HIPS or ABS able to support a load of 13.635 MT tested in accordance with ASTMD 4280 type H and other requirement mentioned in MoRT&H circular its reflective lens made of micro prismatic lens (capable of providing total internal reflection of light ), electronically welded to the body. The length, height and wiedth of the body shall not exceed 130mm 20mm, and 105mm respectively, The area of each reflective surface shall not be less than 13 Sq. cm. on each side stoping at the angle of 35+5 degree to the base to ensure maximum reflectively. it shall comply to specification of category A of MoRT&H circular no. RW/NH 33023/10/97-DO-III dated 11.06.97 lenses shall be moulded of methyl methecrylate corforming to ASTMD 788 or equivalent. with 7 years warranty. Rate shall be inclusive of all taxes, royalty, VAT etc. All T&P machine and labour required for proper completion of work.Note: The composite warranty jointly signed by original manufacturer & authorized converter of at l( SOR 2022 SI.N. 22.05 NEW ITEM ) |
| 5 | Supply of 22.4 to 53 mm gauge stone ballast with stacking for measurment etc all complete as per the direction of engineer in charge.RMR |
| 6 | Supply of Screeing material with stacking for measurment etc all complete as per the direction of engineer in charge.RMR |
| 7 | Consolidation of stone aggregates of 45-63 mm/22.4-53mm size to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2/3 as per Technical Specification Clause 405.(SOR 2022 SI. N. 20.02 ITEM N. 752) |
| 8 | Supply & laying 80 mm thick Precase cement concrete ishape interlocking paver block (Grey color) with top layer of minimum 8 mm thickness having plan dimension 200X(160+120mm) of O.P cement smoothing gloss finish,skid resistant manufacturered from rubber moulds M-30 GRADE AS PER SOR 2022. |
| 9 | S/L C:C (1:2:4) with 20 mm stone grit, coarse sand & cement etc all complete as the direction of engineer in charge. (AS PER PWD SOR 2022 PAGE NO 18 SI NO 5.07 ITEM NO 279(a).] |
| 10 | DPR CHARGE etc all completed as per the direction of engineer - in - charge. |
| 11 | BOARD FIXING CHARGE |
| 12 | GST Please Enable Macros to View BoQ information |
