|
| 1 | Supplying fitting and fixing M.S grill gate with M.S grill made of 20 x 6 mm M.S flats or 16 mm M.S square bras fitted on 25x25x6 mm M.S angle frame -- do -- (where materials is not supplied by the deptt.) |
| 2 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 40MMX 40MMX 5MM |
| 3 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides |
| 4 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : |
| 5 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion,(i) Single socketed pipes.12.41.2 110 mm diameter |
| 6 | Supplying fitting and fixing glass panes including supplying putty. Beads and nails after taking out old and broken glass panes and disposal of debris all complete as per building specification and direction of E/I .5.5 mm plain |
| 7 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 8 | Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 10 | Excavation for roadwork in Ordinary Rock with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m |
| 11 | Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 12 | Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but withoutfittings and the base support for tank. |
| 13 | Supplying, fitting and fixing 20 guage G.C.I. Sheet gate fitted on M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. |
| 14 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke andsalt) as required. |
| 15 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess forconnections etc. as required |
| 16 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess forloop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 17 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 510x1040 mm bowl depth 250 mm |
| 18 | Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortaR |
| 19 | Providing designation 75B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, costs of screening, materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I. |
| 20 | Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 21 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 22 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floors and taxes all complete as per building specification and direction of E/l. |
| 23 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door-110mm dia |
| 24 | Plain tee - 110mm |
| 25 | plain band - 110mm |
| 26 | Providing and fixing brass bib cock of approved quality :18.15.1 15 mm nominal bore |
| 27 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply, including all CPVC plain &brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cementand the cost of cutting chases and making good the same including testingof joints complete as per direction of Engineer in ChargeEarth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and do - do - as per approved design, building specification and direction of E/l. 15 mm nominal dia Pipes |
| 28 | 20 mm nominal dia Pipes |
| 29 | 25 mm nominal dia Pipes |
| 30 | Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 31 | Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (+ 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer’s specification and direction Engineer -in- charge. |
| 32 | 35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineerin- charge.9.142.1 Non decorative finish (matt finish) |
| 33 | Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. Of parry Hindustan or any other I.S.S. Approved make with 100mm H.C.I. 'P' trap 15liters C.I. Pull and let go flushing cistern of names or other I.S.S. Equipment make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pert of vitreous white glazed earthenwere were footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. |
| 34 | Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed C.l. or R.S. brackets 32 m C.I. brass waste 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32 mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l. |
| 35 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. |
| 36 | Supply, Installation, testing and commissioning of following, size ceiling fan 3 Blades confirming to IS : 374 : 2019 including wiring the down rods of standard length (up to 30cm) with 1.5 sq.mm. FR PVC insulated, copper wire suitable for 230V 50Hz, single phase supply etc. complete as required.1200mm (48\\") ceiling Fan |
| 37 | CIRCUIT / SUBMAIN WIRING 2x1.5 sq mm + 1x1.5 sq mm earth wire |
| 38 | 2x2.5 sq mm + 1x2.5 sq mm earth wire |
| 39 | 4x2.5 sq mm + 2x2.5 sq mm earth wire |
| 40 | Welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint of approved shade over a coat of primer (Priming & Painting to be paid for separately) |
| 41 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. |
| 42 | Carriage of material Sand |
| 43 | Stone Chips |
| 44 | Bricks |
| 45 | Fly Ash Lead - 15km |
| 46 | Local Sand - 3 km |
| 47 | E/W in excavation of foundation trenches do-do-all complete job as per specification and direction of E/I |
| 48 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 49 | Providing R.D.R.R. Stone masonary with c.m.(1:3) in foundation -do-do- all complete |
| 50 | Providing R.D.R.R. Stone masonary with c.m.(1:3) in substructure -do-do- all complete |
| 51 | providing Filter media -do-do- all complete |
| 52 | Earthwork in excavation in foundation trenches in ordinary soil ( vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts,levelling, ramming the foundation trenches, removing roots of trees,shurbs all complete as per approved design, building specification and direction of Ei I |
| 53 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 54 | Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 55 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 56 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixedwith polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumenand G.I. limpet washers or with G.I. limpet washers filled with white lead, includinga coat of approved steel primer and two coats of approved paint on overlappingof sheets complete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to sizeand shape wherever required.12.1.1 1.00 mm thick with zinc coating not less than 275 gm/m |
| 57 | Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B) |
| 58 | Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation frenches within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume). |
| 59 | Providing designation 75 B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15 mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l. |
| 60 | Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 61 | Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9\\"x4.5\\"x3\\") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I. |
| 62 | 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size) |
| 63 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to Plinth Level- 1:1.5:3 (1 cement ; 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size) |
| 64 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string course, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reionforcement :(1:1.5:3 (1 cement : 1.5 : coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size) |
| 65 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15\\" landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20mm nominal size). |
| 66 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, fotting, bases of columns, etc. for mass concrete |
| 67 | Suspended Floors, roofs, landings, balconies and access platform |
| 68 | Lintels, beams, Plinth beams, girders, bressumers and cantilevers |
| 69 | Column, Pillars, Piers, Abutments, Posts and struts |
| 70 | Providing Toe steel reinforcement of following dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL, TATA Steel, JSPL, Electro Steel Ltd. and Vizal Steel) |
| 71 | 8mm @50% |
| 72 | 12mm to 25mm @ 30 % |
| 73 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 74 | Providing 12mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 75 | Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 76 | Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement Area shall be multiplied by the co-efficient as indicated in building specificatio). |
| 77 | Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 78 | Providing 150mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I. |
| 79 | Making plith protection 50mm thick of cement concrete 1:3:6 (1 Cement : 3 coase sand ( zone-III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth |
| 80 | Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with integral water proofing compound Liquid @125mi per bag cement including screening, |
| 81 | Providing and fixing Ist quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black ofany size as approved by Engineer-in-Charge, in skirting, risers of stepsand dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shadecomplete. |
| 82 | Providing and fixing angle iron frames for doors, windows and ventilatorsof mild steel Angle sections of size 35x35x5 mm, joints mitred andwelded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existingT-iron frame or to the wall with dash fastener, including fixing of necessarybutt hinges and screws and applying a priming coat of approved steelprimer, all complete as per the direction of Engineer-In-charge. |
| 83 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1stquality conforming to IS : 15622, of approved make, in colours White,Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4(1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm including grouting the joints with white cement and matchingpigments etc., complete. |
| 84 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) |
| 85 | Providing, hoisting and fixing above plinth level up to floor five level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 86 | Granite stone slab of all colour and texture except black, Cherry/ Ruby red |
| 87 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 88 | Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level.1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40mm nominal size) |
| 89 | Providing Toe steel reinforcement of following dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL, TATA Steel, JSPL, Electro Steel Ltd. and Vizal Steel)10mm dia |
| 90 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I. |
| 91 | Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I. |
| 92 | Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soiland rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tooIs,driIing rig,air compressure and equipmentsas well as fule, lubricants and cost of transportation of rig machine and other vehical up to Site. (a) From 0.00 M to 50.00 M below G.L. |
| 93 | (b) From 51.0 M to125.00 M |
| 94 | (c) From126.0 M to150.00 M |
| 95 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia |
| 96 | Development of tube well in accordance with IS : 2800 (part I) andls:11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by \\"V\\" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all compIete,incIuding hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge |
| 97 | Providing and fixing suitable size threaded mild steel cap or spot weldedplate to the top of bore well housing/ casing pipe, removable £lS £'Frequirement, all complete for borewell of: p200 mm dia |
| 98 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp |
| 99 | Supplying Submersible pump sets confirming to IS 8034 and motorconfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thrust carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible Pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages - 2 HP |
| 100 | Supplying Fully automatic star delta starter to operate induction motorworking on 415V, 3 phase, 50 hz with no volt coil, Over load element, ON- OFF push buttons, with necessary materials and connected to supply, etc. complete starter with original sheet steel encloser as per IS : 3914 |
| 101 | Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job dS per direction of E/I. |
| 102 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work - 50 mm nominal dia Pipes |
| 103 | Supplying and stacking of good eaeth at siteincluding royalty and carriage up to 1 kg300mm THICK |
| 104 | extra crriage up to 3kg |
| 105 | Supplying and stacking of well decayed cow dung manure at site including loading unloading andcarriage for 1km lead. 40.0% area of totalx75mm |
| 106 | Fine dressing the trenched ground includingbreaking clods (40.0% area of total) |
| 107 | Spreding of sludge dump manure or / and good earth in required thickness including carriage thickness including carriage of materials for lead upto 500m and loading unloading and stacking as per direction of Engineer in charge (cost of sludge dump manure or/and good earth to be paid separately) (qty 5+7) |
| 108 | Digging holes in ordidinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1by vaIume(2parts of stacked volume of earth after reduction by 20%:1part of stacked volume of manure after reduction by 8%)fIooding with water ,dressing including removal of rubbish and surplus earth ,if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separatly ) Holes 45 m dia and 45mdeep. (no of Plant.) |
| 109 | perparation of mounds of various size shape by avallabie excavated/ supplied earth in layers not exceediung 20cm in depth , breaking clods watering of each layer dressing etc. lead upto 50 meter and lift up to 1.5 m as directed. (Assume) |
| 110 | Making tree guard as per design from surb plant RED Hedge/ Duranta Golden plant supplied, Providing, fixing and 30 days maintained with all complete job. ( Earth Boarder of 0.30m) |
| 111 | Providing and disply of Araucaria cookie plant of 3 ' -3 1/2 ht . Straight. Fresh and healthy lush green leaves from bottom to top ,well development , in 12\\" E/ pots &as per direction of the officer - in charge. |
| 112 | Providing and displying of Areca Palm plant of ht 3 to 4' with 3-4 branch full of fresh and heathy leave well development in 10\\" E pots &as perdirection of the officer - in charge. |
| 113 | Providing and disply of Croton Petra Bangalore plant of ht 3 to 4' with 3-4 branch full of fresh and heathy leave well development in 10\\" E pots &as per direction of the officer - in charge. |
| 114 | Providing and disply of Livistoa Palm plant having on3’ ht moss 60 cm to 75cm distance, full of fresh and healthy leaves well development ,10\\" Earthen POTS & as per direction of the offocers -in charge. |
| 115 | Providing and disply of Raphis Palm plant having ht 75 cm to 90cm distance, full of fresh and healthy leaves well development ,10\\" E POTS & as per direction of the offocers -in charge. |
| 116 | 4.0-Seasonal Plants |
| 117 | providing and displying plant antirrhinum hybrid dwarf varity (8-10 plants ) with fresh & healthy foliage in full bloom well developed in 35 cm earthen tray / challi pot and as per diection of the officer in charge |
| 118 | providing and displying plants cineraia long 45 to 60 cm ht, 8 to 10branch with full bloom specimen plants with green painted stacking in 30 cm earthen pot /pIastic pot and as per direction of the officer in charge. |
| 119 | providing and displying plants Dahlia kenya varity in different colour well development with 3 to 4 flowers in half bloom , good foliage stacked with green painted bamboo stivks , 45 to 60 cm height in 25 cm earthen pot / plastick pot and as per direction of the officer in charge. |
| 120 | providing and displying plants Dianthus dwarf in spcimen 6-8 plants in a pot with fresh & healthy foliage in full bloom well developed in 35 cm earthen tray / nand as per direction of the officer - in - charge. |
| 121 | providing and displying plants marigold jaffri dwarf in different colour well developed with fresh &heIthy foliage with 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht . In 20 cm earthen pot /pIastic pot and as per direction of the oPicer incharge. |
| 122 | providing and displying plants Pansy hybrid sakata with fresh &heaIthy foliage with 3 to 4 flower in bloom in 20 cm earthen poll plastic pot and as per direction of the officer incharge. |
| 123 | providing and displying plants petunia hybird well develooped withfresh & healthy foliage in full bloom 6-8 plants in 35 cm earthen tray /nands per direction of the officer incharge. |
| 124 | providing and displying plants Ranunculus hybrid varity in different colour specimen 5-6 plants in each pot with fresh & health foliage in full bloom well developed in 35 cm earthen tray / nand as per of the officer incharge. |
| 125 | providing and displying plants standerd rose ( h.t varity to 4 healthy branch 90 cm and above ht. Well developed with one above flower sin 25 cm earthen pot/plastic direction of the |
| 126 | providing and displying cycus revoluta specimen plant , having 45 to 50 fresh and healthy , leaves having 30 cm to 35 cm circumfrance of base stem well developed in 40 cm chall i. As per direction of the officer in charge |
| 127 | providing and displying ficus black vivon pillar topiary plant (sylinder type )weII developed with fresh and healthy 180 to 210 cm ht in 40cm cement pot as per direction of the officer in charge. |
| 128 | providing and displying FoxTail plam pant well developed with fresh and helthy foliage leaves of ht 210 to 240 to cm specimen plant in 40 cm cement pot as per direction of the office incharge. |
| 129 | supply and stacking ofplant tecoma stans of heigh 90-105 , 90-105 cm bushy in big size HDPE bag as per direction of the officer in charge |
| 130 | supply and stacking of plant Thuja compacta of heigh75-90 conical shaped well formed with healthy foliage in earthen pots of size 30 cm as per direction of the officer in charge |
| 131 | supply and stacking of Bignonia venusta ( golden shower )pIants of height 30 cm to 45 cm in 20 cm size of earthen pots / plastic pots &as per direction of the office- in -charge. |
| 132 | REAL WATER--Realwater Reverse Osmosis based Water Treatment System above 50 LPH Capacity Above 50 LPH and upto100 LPH Storage Tank (Inclusive in the scope of Supply) No NA (for without storage tank) |
| 133 | SANRIAN Storage Type Water Cooler 80 LPH Cooling CapacitySANRIANR(SWC80120) |
| 134 | Add 18 % GST (in Basic Rate must fill 12) |
| 135 | Add 1% Labour Cess (in Basic Rate must fill 1) Please Enable Macros to View BoQ information |
