|
| 1 | PART -A CIVIL WORK (BSR 2022) |
| 2 | Supplying and fixing machine cut dressed 75 mm Pink sand stone (Bansi Paharpur) dasa/ coping wth ornamental shape having moulding and \\"PAN Shape\\" engraving as per required pattern with engraving depth of 5 mm (average) in single piece of length 90 cm to be laid on cement mortar 1:4 (12 to 20mm thick) including pointing with admixture of pigment matching with the stone shade |
| 3 | Providing and fixing 18mm thick grey Granite stone tile shot blasted flammed brushed and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing completeJhunjhunu / Jalore (Red/Choclate/Black/Pink Colour)Above 3601 Cm2 Slabs |
| 4 | Plaster on new surface on walls in cement sand mortar 1:4including racking of joints etc. complete fine finish :(Excluding cost of cement) |
| 5 | 25mm thick . |
| 6 | Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m , disposed earth to be levelled and neatly dressed: All kinds of soil |
| 7 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. |
| 8 | CARRIGE Earth, Sand, Lime, Morrum manure or sludge UP TO 10KM |
| 9 | Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm ). |
| 10 | Finishing walls with textured exterior paint of required shade as per approved colour complete as per manufacturers specifications including primer coat and protecting coat including scaffolding and safety provision |
| 11 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work |
| 12 | STALWART |
| 13 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.M15 grade Nominal Mix (graded stone aggregate 20mm nominal size). |
| 14 | Providing and laying in position specified grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement.M20 grade Nominal Mix / Design Mix |
| 15 | Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation , footings, strap beam, raft , bases of columns etc. |
| 16 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. ('Original producers' who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786)Thermo-mechanically Treated bars (Conforming of relevent IS code) |
| 17 | SANITARY WORK (BSR 2022) |
| 18 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall)(A) Exposed on wall 40mm dia nominal bore |
| 19 | 40mm dia nominal bore |
| 20 | P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make : 40mm dia nominal bore |
| 21 | Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size : 40mm dia nominal bore |
| 22 | Providing & Laying C.C. 1:5:10 (Stone aggregate 40mm nominal size) all around S.W. pipe including 15 Cm. thick bed concrete (Width W= Diameter of pipe in Cm+30 Cm.)( Excluding cost of pipe).(BSR 2019 -S-3.2.3) 200mm dia Internal |
| 23 | Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. |
| 24 | -do- size 600 x 450mm depth upto 0.5 M Cement cover with frame. |
| 25 | Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work. |
| 26 | 200mm dia |
| 27 | Un-lowering of submersible pump set with all piping from a tube-well/ open-well complete (labour charge only ) including transportation of tripod, chain, pulley-block and other materials required and lowering of repaired/ new pump in the tube-well / open-well complete in all respect. |
| 28 | S & F tube well cover of M.S.sheet (6mm thick) with nuts and bolts complete for casing size: |
| 29 | 200mm dia |
| 30 | S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 31 | Development of tube well as per IS specification using suitable compressor to give sand free water for required yield of the gravel packed tube well. |
| 32 | Part - B TUBE WELL (BSR 2022) |
| 33 | P / L of Double wall corrugated HDPE pipe confirming to IS : 16205 P-24, Stiffness Class 750 N, Externally corrugated and having smooth surface inside with HDPE Coupler, Elbow, Tee at required Depth below the ground for laying cable of following Nominal Outer dia. MFR Test report from NABL accrediated is to be submitted.(Excavation of Earth & Back filling with compaction is to be Paid Extra)All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 34 | 200 mm Dia. |
| 35 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 4.0 Sq. mm 3 core |
| 36 | 4.0 Sq. mm 3 core |
| 37 | SITC of Contactor OEM Fabricated DOL/Star-Delta Starter panel with switchgear selection as per Type-2 Cordinatiom Chart and made out from 1.6 mm thick powder coated CRCA sheet, enclosure comprising of over load protection relay, short circuit & single phasing protection, Illuminated ON / OFF push buttons, ammeter, voltmeter, indicating lamps etc. suitable for following rating motors complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 38 | For Three phase Submersible / Mono block pump 3.0 HP to 5.0 HP ( DOL starter ) |
| 39 | Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR |
| 40 | Triple pole MCB (With B/C curve trippingCharacteristics) |
| 41 | 6 A to 32 A rating |
| 42 | SITC of Radial / mixed flow ISI marked water and anti-corrosive liquid filled submersible motor pump sets suitable for 100/150mm dia borewell. The size of adopter fixed on top of the motor should exceed the top of coupler , for safegaurd the coupler. The construction material of motor and pump should match IS: 8034 : 2018 and IS: 9283 guideline. The radial flow pumpset should operate at 5 star energy efficiency level of BEE and mixed flow pump set should operate at 3 star energy level of BEE, accompained by valid BEE certificate. Motor should be IE2 class as per IEC 60034-2-1: 2007, IEC 60034-30: 2008, & IS12615:2011 with required accessories including making connection suitable for Bore well. The job includes labour part of lowering of riser pipe G.I./ H.D.P.E. with rope, cables & pump, installation of complete fitting and accessories, jointing of electrical cables up to Starter. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 43 | 150 mm diameter Submersible pump shall have following HP Rating, phase, Head range, Discharge range respectively. 3.0 HP, 3-Ø, (54 -95)Mtr, (250-50) LPM |
| 44 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 45 | Grade 304 |
| 46 | PART -C NBSR ITEM |
| 47 | Providing and fixing Glass Mosaic tiles 20mmx20mmx4mm size manufactured by CEFINO OR PEARLS and equivalent and approved shade and design with required adhesive over bad of 15 mm thick cement sand mortar 1 : 3 inclusive nicely finished joints(thickness of joints shall not be more than 1.5 mm) using water proof joints filter( as recommended by manufacturer) and finishing with flush pointing in white cement and mixed with pigment to match the shde of the tile etc complete as directe by engineer in-charge and Architect |
| 48 | Providing & fixing Banswara White stone marble in Pedestal cladding / Flooring Structural base with white cement & Tinex chamical, & SS CLAMP and Fastners (of approved brand), moulding laid and jointed with white cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing as per drawing attached complete in all respect as per direction of Enginner- In- Charge & Architect with all lead & lift loadig,unloading scafolding,T&P,machinary. The Stone measurement will be done of outer most dimension. Thickness of stone 20-25 mm. |
| 49 | Providing and fixing of Gun Metal different items including transportation,installation and inclusive of all taxes and design/pattern as per the directions of Engineer-incharge and Architect.Composition of Gun Metal must be 88% Copper, 10% Tin and 2 % Zinc , |
| 50 | (viii)B.R.AMBEDKAR TO HON. PRESIDENT D.R. RAJENDRA PRASAD Sculpture of height 3'6\\" |
| 51 | Dressesd Bansi Pahadpur Stone in tradditional style cladding/flooring patterns over 25 and 50mm thick base in cement mortar 1:6 including pointing with cement mortar 1:2 (1 cement :2 stone dust) with an admixture of pigment to match the shade of stone with joint thickness upto 1.5mm as per enclosed drawing, details and directions of engineer in chrge and Architect.Including all lead, lift, loading, unloading, Scafolding,T&P,all material like pigment, cement etc.,and machinery. |
| 52 | Labour Charges Engraving of 22 PARTS OF CONSTITUTION on Existing Dholpur sand stone /white Banswara Stone Cladding filling with galaxy oil paint as required architects complete work carried out as per direction of engineer in charge / Architect. Please Enable Macros to View BoQ information |
