|
| 1 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc. and getting out in soft/loose soil complete all as per specified and as directed by Engineer-in-charge. |
| 2 | Returning, filling in, including spreading, leveling, watering and well ramming in layers n exc 25cm complete all as per specified and as directed by Engineer-in-charge. |
| 3 | Removing excavated material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as per specified and as directed by Engineer-in-charge. |
| 4 | M&L for Hardcore with broken stones/ boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and as directed by Engineer-in-charge. |
| 5 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge. |
| 6 | M&L for resecuring or easing & adjusting without taking down of wooden door/ window/ ventilator/ cup board Shutters of any description, including refixing/tightening of hinges, handles, tower bolts and other accessories with and including providing new brass CP screws (If required), complete all as specified and as directed by Engineer-in-charge. |
| 7 | M&L for resecuring or easing & adjusting without taking down of aluminium partitions/ door/ window Shutters of any description, including refixing/tightening of hinges, handles, tower bolts and other accessories with and including providing new brass CP screws, aluminium snap beading, rubber gasket, etc. (If required), complete all as specified and as directed by Engineer-in-charge. |
| 8 | S&F in-repair of Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and as directed by Engineer-in-charge. |
| 9 | S&F in-repair of Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, complete all as specified and as directed by Engineer-in-charge. |
| 10 | Providing and fixing in-repair of factory made uPVC white color Sliding window (Area exceeding 2.00 sqm each) Two track made of extruded profiles with wall thickness of 2.3mm (+- 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass, aluminum track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock.] (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) |
| 11 | M&L for providing and laying in-replacement of 300mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and as directed by Engineer-in-charge. |
| 12 | M&L for providing and laying in-replacement of 450mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars, complete all as specified and as directed by Engineer-in-charge. |
| 13 | S&F of 10mm thick Sheet glass, ordinary quality, glazing with u-pvc snap beading in square/ rectangular exc 0.5 sq. m in each pane, complete all as specified and as directed by Engineer-in-charge. (NOTE- Cost of upvc snap beading/glazing clips will be measured and paid under item no. 10 of BOQ) |
| 14 | S&F in-repair of 140 mm Overall length of cover plate Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and rubber end, fixed in floor, complete all as specified and as directed by Engineer-in-charge. |
| 15 | S&F of 5mm thick self adhesive rubber beading strips of width in between 3-5cm for sealing of door/window gaps to prevent entry of insects, complete all as specified and as directed by Engineer-in-charge. |
| 16 | S&F in-repair of 20 mm dia mild steel, chromium plated curtain rail with fixing brackets, stops, rollers etc., complete all as specified and as directed by Engineer-in-charge. |
| 17 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius built and set in cement mortar 1:6, incl demolition of existing B/W,complete all as per specified and as directed by Engineer-in-charge. |
| 18 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built and set in cement mortar 1:4, incl demolition of existing B/W,complete all as per specified and as directed by Engineer-in-charge. |
| 19 | M&L for Rendering 10mm thick in cement morter 1:6 on fair faces of brick work or concrete surfaces/ one side of lathing, finished even and smooth (without using extra cement), complete all as specified and as directed by Engineer-in-charge. |
| 20 | M&L for Rendering (Externally) 15mm thick in Cement Mortar 1:4 on other than fair faces Brick Walls/Concrete Surfaces/ other side of lathing, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed by Engineer-in-charge. |
| 21 | M&L for PCC 1:4:8 type D-2 (40mm graded stone aggregate) as in foundations, fillings and mass concrete with necessary formworks (as/if required), complete all as per specified and as directed by Engineer-in-charge. |
| 22 | M&L for Providing Cement Concrete 1:2:4, type B-1 (20mm graded aggregate) as in benching/Coping, edging, lintels upto 1.5m clear span, cills, steps; hold-fast block, filling in pressed steel frames, seismic and other similar bands etc. and finishing the Concrete surfaces Fair and Even including necessary Formwork required at Site(s) including demolition of existing old damaged PCC, complete all as specified and as directed by Engineer-in-charge. |
| 23 | M&L for precast reinforced cement concrete 1:2:4, type-B1 (Using 20 mm graded stone aggregate) in landings, cover slabs (for manholes, etc.) and similar articles with plain faces and set in cement mortar 1:4, including demolition of existing old damaged RCC, complete all as per specified and as directed by Engineer-in-charge. NOTE : Reinforcement will be measured and paid separately under relevant Item. |
| 24 | S&F of TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed by Engineer-in-charge. |
| 25 | M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) in surface channels and drains, including necessary formwork and demolition of existing damaged drains, complete all as specified and as directed by Engineer-in-charge. |
| 26 | M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends, complete all as specified and as directed by Engineer-in-charge. |
| 27 | Add to or Deduct from Item No. 26 here-in-before for Every 25mm Girth or Part thereof Over or Under 30 Cm, complete all as specified and as directed by Engineer-in-charge. Note:- Quantity of this item shall be changed as per site requirement. |
| 28 | M&L for providing 100 mm thick Cement concrete type B-2, 1:2:4 (40mm graded stone aggregate) as in floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including filling joints with bitumen and sand mixture of 1:3, use and waste of form work and finishing concrete surfaces even and fair and demolition of existing old damaged PCC of any type, complete all as per specified and as directed by Engineer-in-charge. |
| 29 | M&L for providing 75mm thick Cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in floor/ path/ hardstanding/plinth protection, etc. or similar works, laid in altenate bays including filling joints with bitumen and sand mixture of 1:3, use and waste of form work and finishing concrete surfaces even and fair and demolition of existing old damaged PCC of any type, complete all as per specified and as directed by Engineer-in-charge. |
| 30 | M&L for providing Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., laid over 20mm thick cement screed 1:6 set and jointed in neat cement slurry and pointed in white or coloured cement to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge. |
| 31 | M&L for providing Glazed ceramic coloured tiles in vertical surface (like skirting, dado, etc.) 300x 450x 7 mm thick, over 10mm thick cement screed 1:3 set and jointed in neat cement slurry and pointed in white or colour cement to match, including dismantling of existing old damaged tiles of any type, complete all as per specified and as directed by Engineer-in-charge. |
| 32 | M&L for providing glossy finished Chequered cement concrete coloured tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors., laid over 20mm thick cement screed 1:6 with grey cement and pigments to match, including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge. |
| 33 | M&L for providing Machine pressed precast coloured concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade, with grey cement and pigment, including dismantling the existing old unserviceable paver block of any type and of any description, complete all as per specified and as directed by Engineer-in-charge. |
| 34 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), includingmaking drainage opening wherever required including dismantling the existing old unserviceable tiles of any type and of any description, complete all as per specified and as directed by Engineer-in-charge. |
| 35 | S&F in-repair of 2.5mm dia hot dip galvanised steel wire concertina coil of 600mm dia (Coil dia in stretched position) with CLR anti-corrossive coating fixing in angle iron frame as in fencing with hasp-staple and clips, complete all as specified and as directed by Engineer-in-charge. |
| 36 | Fixing only in-repair of Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc.(each line wire to be measured), complete all as specified and as directed by Engineer-in-charge. |
| 37 | M&L for taking out deposited sludge and water from manhole/ covered drain of any size and depth by amnual/ mechanical means and removing sludge out of MOD land including sweeping/cleaning with water and spreader bleaching powder, complete all as specified and directed by Engineer-in-charge. (Only sludge shall be measured). NOTE- Disposal of sludge at outside MoD land shall be at contractor's own arrangement. |
| 38 | M&L for preparing newly plastered surfaces of wall and applying three coats of white wash, complete all as specified and as directed by Engineer-in-charge. |
| 39 | M&L for preparing old plastered or unplastered surfaces of wall and applying one coat of cement base paint of any shade, complete all as specified and as directed by Engineer-in-charge. |
| 40 | M&L for preparing old plastered or unplastered surfaces of wall and applying one coat of distemper oil emulsion of any shade, complete all as specified and as directed by Engineer-in-charge. |
| 41 | M&L for preparing old plastered or unplastered surfaces of wall and applying one coat of white wash, complete all as specified and as directed by Engineer-in-charge. |
| 42 | M&L for preparing old plastered or unplastered surfaces of wall and applying two coats of white wash, complete all as specified and as directed by Engineer-in-charge. |
| 43 | M&L for preparing old plastered or unplastered surfaces of ceiling/ AC ceiling boards and applying one coat of white wash, complete all as specified and as directed by Engineer-in-charge. |
| 44 | M&L for complete removal of existing surface treatment, preparing the surfaces even and smooth by Vaccum based sanding machine and applying by means of auto roller (Smart Painting) Two coats of 100% Premium acrylic smooth emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (as approved) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over a coat of avg. 1.0mm thick Wall care Putty (Multipurpose mixer shall be used for uniform and proper mixing of Putty) (Smart Painting) including rubbing down the surfaces to obtained smooth finished surface, complete all as specified and as directed by Engineer-in-charge. |
| 45 | M&L for preparation of old painted steel/ iron surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge. |
| 46 | M&L for preparation of old painted steel/ iron surfaces of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tint and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge. |
| 47 | M&L for preparation of old painted wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge. |
| 48 | M&L for preparation of old painted wooden Surfaces of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tint and applying one coat of Synthetic enamel paint (1st quality) of any tint, complete all as specified and as directed by Engineer-in-charge. |
| 49 | M&L for Writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high with synthetic enamel paint, complete all as specified and as directed by Engineer-in-charge. |
| 50 | S&F in-repair of solid PVC wall panneling consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification, complete all as specified and as directed by Engineer-in-charge. |
| 51 | S&F of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame, complete all as per specified and as directed by Engineer-in-charge. |
| 52 | S&F in-repair of powder coated Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel suspended from ceiling by means of 4mm dia GI hanger with and including fixing/ laying/ inserting of pre-painted (white) 4mm thick designer classic E-boards (595x595 mm) to GI frame work, complete all as specified and as directed by Engineer-in-charge. |
| 53 | S&F in-repair of sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge. |
| 54 | S&F in-repair of sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engineer-in-charge. |
| 55 | S&F in-repair of plate rack/ kitchen rack made of stainless steel 0.5mm thick overall size 800mm x 900mm x 250mm, fixed to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge. |
| 56 | S&F in-repair of Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white with and including grating, 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe and providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long CP brass screws, pointing around urinal back in putty; complete all as specified and as directed by Engineer-in-charge. |
| 57 | S&F in-repair of Vitreous China wash basin oval counter top type, white, self rimming basin, flat back, size 560x410mm including fixing of 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe with and including 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and as directed by Engineer-in-charge. |
| 58 | S&F in-repair of Vitreous China wash basin, white, with brackets, flat back, size 550x400mm including cutting for and pinning in ends of brackets or erecting stand including providing 32mm dia CP Waste fittings, 15mm dia 450mm long PVC connection pipe and 32mm dia 900mm long PVC Flexible waste pipe, complete all as specified and as directed by Engineer-in-charge. |
| 59 | S&F in-repair of Wash down couple water closet (Cistern mounted) pan and S/P trap of 670x365x740mm with and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device including connection to drain (or outgoing pipe) and antisyphonage pipe, etc., complete all as specified and as directed by Engineer-in-charge. |
| 60 | S&F in-repair of Wash down water closet (Pedestal pattern) pan and S/P trap of 540x375x415mm with and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and as directed by Engineer-in-charge. |
| 61 | S&F in-repair of vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc., complete all as specified and as directed by Engineer-in-charge. |
| 62 | S&F in-repair of 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm dia, with and including making necessary connections, complete all as specified and as directed by Engineer-in-charge. |
| 63 | S&F in-repair of Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or anodised aluminium hinging device, complete all as specified and as directed by Engineer-in-charge. |
| 64 | S&F in repair PVC water tank cover suitable for any capacity PVC water tank 6mm dia MS bar hinging device and S type locking arrangements, complete all as specified and as directed by Engineer-in-charge. |
| 65 | S&F in-repair of PVC connection pipe 15mm dia with PTMT nuts of length 450mm, complete all as specified and as directed by Engineer-in-charge. |
| 66 | S&F in-repair of stainless steel Grating doom of 100/125 mm dia with/ without waste hole, complete all as specified and as directed by Engineer-in-charge. |
| 67 | S&F in-repair of 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/ fixed to wall/ ceiling, complete all as specified and as directed by Engineer-in-charge. |
| 68 | S&F in-repair of 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/ fixed to wall/ ceiling, complete all as specified and as directed by Engineer-in-charge. |
| 69 | S&F in-repair of 110mm dia PVC (SWR) bends any radius with access door, complete all as specified and as directed by Engineer-in-charge. |
| 70 | S&F in-repair of 75mm dia PVC (SWR) bends any radius with access door, complete all as specified and as directed by Engineer-in-charge. |
| 71 | M&L for petty repair to bib tap/ pillar tap/ stop valve/ angle valve of any type and size by replacing washer/ spindle and cleaning the inside, complete all as specified and as directed by Engineer-in-charge. |
| 72 | S&F in-repair of 15 mm dia fancy type, chromium plated Stop valves/ Angle valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and as directed by Engineer-in-charge. |
| 73 | S&F in-repair of 15mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge. |
| 74 | S&F in-repair of 20mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge. |
| 75 | S&F in-repair of 25mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge. |
| 76 | Fixing only in-repair of 15-25mm dia galvanised steel tubes, 'medium grade', with all fitting; fixed to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge. |
| 77 | M&L for Disconnecting existing PVC tank, setting aside (or lowering if required) and Cleaning of service water tank exc 250 and n.exc 500 ltrs capacity and connected circulating pipes at any position by removing sludge, mud, moss, moulds, efflorescent salts, oil spots etc or any other foreign material from the bottom, cover and internal surfaces by scraping using wire brush draining out the water in the tank and washing internally by using bleaching powder and again draining out the water in the tank and applying single coat of lime washing on all tanks and marking the date of cleaning with white paint on black back ground including reconnecting and re-fixing in original position complete all as specified and as directed by Engineer-in-charge. |
| 78 | All as per Item No. 77 here-in-above, but for 1000 Litre tank, complete all as specified and as directed by Engineer-in-charge. |
| 79 | S&F in-repair of Rotational Moulded Polyethylene Water Storage Tank 500 Litre capacity (Cylindrical Vertical with Closed Top), 3 layered, hoisted and fixed in position, all as specified in MES Schedule Part-I with and including providing 20 mm dia float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210gm), complete all as specified and as directed by Engineer-in-charge. |
| 80 | All as per Item No. 79 here-in-above, but for 1000 Litre tank, complete all as specified and as directed by Engineer-in-charge. |
| 81 | S&F of 20 mm dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 210gm), complete all as specified and as directed by Engineer-in-charge. |
| 82 | S&F in-repair of 15 mm dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms), complete all as specified and as directed by Engineer-in-charge. |
| 83 | S&F of 20 mm bore (dia), gun metal gate valves with iron wheel head, screwed both ends for iron pipe, ISI Marked, as per IS: 778 and including taking out old unserviceable gate valves complete all as specified and as directed by Engineer-in-charge. |
| 84 | S&F in-repair of corner Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf with chromium plated bracket guard and railing 30cm long, complete all as specified and as directed by Engineer-in-charge. |
| 85 | S&F in-repair of bevelled edge mirror 600x450mm of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed by Engineer-in-charge. |
| 86 | S&F in-repair of 32/40mm dia Waste coupling of PTMT (half or full threaded) (Minimum weight- 45gms), complete all as specified and as directed by Engineer-in-charge. |
| 87 | S&F in-repair of Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and as directed by Engineer-in-charge. |
| 88 | S&F in-repair of Brass chromium plated towel rack/ shelf, 300mm wide, 600mm long between flanges, complete all as specified and as directed by Engineer-in-charge. |
| 89 | S&F in-repair of Brass chromium plated towel ring, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge. |
| 90 | S&F in-repair of Brass chromium plated Soap Dish of 160x160x90mm in size, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge. |
| 91 | S&F in-repair of Brass chromium plated Toilet paper holder flat recessed type, fixing to wall with CP brass screws, complete all as specified and as directed by Engineer-in-charge. |
| 92 | S&F in-repair of 15 mm dia fancy type Brass CP telephonic wall mixer (3-in-1) for mixing hot & cold water, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge. |
| 93 | S&F in-repair of Brass chromium plated shower rose with arm of 125mm dia of rose, fixing to existing pipe or union of 15 mm dia, complete all as specified and as directed by Engineer-in-charge. |
| 94 | S&F in-repair of 15 mm dia fancy type chromium plated Pillar taps, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed by Engineer-in-charge. |
| 95 | S&F in-repair of 15 mm dia fancy type chromium plated Bib tap with wall flange, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed by Engineer-in-charge. |
| 96 | S&F in-repair of Health faucet ABS Body chromium plated suitable for 15 mm dia pipe with 1.0 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
