|
| 1 | By Mechanical Transport including loading,unloading and stacking Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - Item to be applicable in urban areas having directions for restricted hours for movement/plying of load carrying motor vehicle of 3.5 cum or more. |
| 2 | Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6(1 cement : 6 coarse sand) |
| 5 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4(1 cement :4 coarse sand) |
| 6 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : Red sand stone - Exposed face machine cut and table rubbed with rough backing. 40 mm thick |
| 7 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) White sand stone - Exposed face machine cut and table rubbed with rough backing. 40 mm thick |
| 8 | Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading |
| 9 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm |
| 10 | Providing and fixing bright finished brass handles with screws etc. complete: 75 mm |
| 11 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 12 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm |
| 13 | Providing and fixing Bamboo jaffery/ fencing consisting of superior quality 25 mm dia (Average) half cut bamboo placed vertically and fixed together with three numbers horizontal running members of hollock wood in scantling of section 50X25 mm, fixed with nails and G.I wire on existing support complete as per direction of Engineer-in-charge. |
| 14 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre). |
| 15 | Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces |
| 16 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 17 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 18 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick |
| 19 | 40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar.Red sand stone |
| 20 | Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3 mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete.0.80 mm thick with zinc coating not less than 275 gm/m2 |
| 21 | Providing gola 75x75 mm in cement concrete 1:2:4(1 cement :2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design : In 75x75 mm deep chase |
| 22 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 23 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 24 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 110 mm bend |
| 25 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm |
| 26 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, difusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board |
| 27 | 12 mm cement plaster of mix: 1:6 (1 cement: 6 coarse sand) |
| 28 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6(1 cement: 6 coarse sand) |
| 29 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 30 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 31 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 32 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 33 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work |
| 34 | Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coat applied @ 1.67 Itr/ 10 sqm) on existing cement paint surface |
| 35 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing suficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. using melamine clear polish and melamine thinner mixed in required. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 36 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 5 mm (weight not less than 12.5kg/sqm) |
| 37 | Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). |
| 38 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 39 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles above 25 mm and up to 40 mm |
| 40 | Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : bituminous road |
| 41 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer- in-charge. |
| 42 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 43 | Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-in-charge. (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage |
| 44 | Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 45 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately). |
| 46 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 47 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes |
| 48 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal dia Pipes |
| 49 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia nominal bore |
| 50 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 51 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions |
| 52 | Shotcreting R.C.C. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by Engineer- in-Charge Note: Rates shall include the providing necessary ground wires etc. The levelling gauges, if used, shall be paid for separately. Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument. 50 mm thick in Grade M25 with cement content not less than 330 kg per cum |
| 53 | Modified Estimated Cost after using correction factor on DSR 2023 on account of GST@ 0.973 (vide No. 158/SE(TAS)/GST/2024/02-E-dated 08.08.2024) |
| 54 | Deduct Cost index @-0.09% |
| 55 | Providing and fixing C.P. brass bib cock with CP brass wall flange of approved make etc. all complete as per direction of Engineer-in-charge. 15 mm nominal bore. (Make Jaquar (code-OPPCHR-15037PM) or equivalent in cost & specifications. |
| 56 | Providing and Fixing Hand Shower (Health faucet) of Jaquar make (Model No. ALD-573) with 8 mm dia, 1 meter long flaxible tube and valve all complete as per direction of Engineer in charge. |
| 57 | Providing and fixing C.P. brass angular stop cock / angle valve with wall flange of approved make etc. complete as per direction of Engineer-in-Charge. (a) 15 mm nominal bore. (Make Jaquar (code-OPP-CHR-15053PM ) or equivalent in cost & specifications. |
| 58 | Providing and fixing C.P. brass Two way bib cock with wall flange of approved make etc. all complete as per direction of Engineer-in-charge. (Make Jaquar (code-OPP-CHR-15041PM) or equivalent in cost & specifications. (a) 15 mm nominal bore. |
| 59 | Providing and fixing C.P. brass towel rail 600 mm long with brackets fixed to wooden clats / rawl plugs with CP brass screws of approved make etc. complete as per direction of Engineer-in-Charge. Make Jaquar Cat.-ACN-1111SM or equivalent in cost & specification. |
| 60 | Providing and fixing C.P. brass soap dish holder with CP brass flange of approved make including fixing with PVC rawl plugs & screws etc. all complete as per direction of Engineer-in-charge. (Make Jaquar (Cat.-ACN-1131N) or equivalent in cost & specifications. |
| 61 | Providing and fixing C.P. brass toilet paper roll holder with flap with CP brass flange of approved make including fixing with PVC rawl plugs & screws etc. complete as per direction of Engineer-in-Charge. Make of Jaquar Cat.-ACN-1153S or equivalent in cost & specifications. |
| 62 | providing and fixing Mortise Lock ,Antique Brass Finish 20cm /8 inches handle , with lock body& 3 Keys etc . Complete as per direction of engineer in charge.Make Godrej Mortise Lock NEH 19-1 CK or equivalent in cost & specifications. |
| 63 | Providing and fixing glass shelf 600mm long /corner glass shelf of Jaquar make code no. ACN-1171N or CAN-1173 or equivalent of approved make etc. complete as per direction of Engineer-in-Charge.) |
| 64 | Providing and fixing C.P. brass soap dispensor with CP brass flange of approved make including fixing with PVC rawl plugs & screws etc. all complete as per direction of Engineer-in-charge. (Make Jaquar (Cat.-AKP-CHR-35735P) or equivalent in cost & specifications. |
| 65 | Providing and Fixing 32mm CP waste coupling of 130mm height for wash basin, Urinal of Jaquar make or qquivalent in cost & specification as per approved sample shape all complete as per direction of engineer-in-charge. |
| 66 | Providing and fixing C.P. brass bottle trap, 32mm nominal bore of approved make etc. all complete as per direction of Engineer-in-charge. Make Jaquar Cat.-ALD-769L300x190 or equivalent in cost & specifications |
| 67 | Providing and fixing Urinal partition Curved 10mm of size (900x450mm) of required length and wall hook of approved make etc. all complete as per direction of Engineer-in-charge. (Make Jaquar Cat-JSE -CHR-110UC450X) or equivalent in cost & specifications |
| 68 | P/f roller blinds of approved colour shade and design i/c aluminium channel folding and felting mechanism chains ete complete at all levels as per direction of Engineer-in-Charge. Vista Classic Make screen fabric without headrail |
| 69 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 600 x 450 mm Clear Opening (heavy duty of load bearing capacity 40 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 70 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 600x750mm Clear Opening (heavy duty of load bearing capacity 40 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 71 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 600x 900 mm Clear Opening (heavy duty of load bearing capacity 20 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 72 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 750 x 900 mm Clear Opening (heavy duty of load bearing capacity 20 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 73 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 450 x 450 mm Clear Opening (heavy duty of load bearing capacity 20 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 74 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 600 x 600 mm Clear Opening (heavy duty of load bearing capacity 20 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 75 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 750 x 750 mm Clear Opening (heavy duty of load bearing capacity 20 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 76 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 900 x 900 mm Clear Opening (heavy duty of load bearing capacity 20 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 77 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 1000 x 1000 mm Clear Opening ( 4 wheeler / Tempo of load bearing capacity 10 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 78 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 600 mm dia Clear Opening (heavy duty of load bearing capacity 40 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 79 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 750 mm dia Clear Opening (heavy duty of load bearing capacity 40 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 80 | Providing and fixing Fibre Reinforced Polymer (FRP) Manhole Cover with the frame of Size 900 mm dia Clear Opening (heavy duty of load bearing capacity 40 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 81 | Providing and fixing Fibre Reinforced Polymer (FRP) gully Cover with the frame of Size 600 x 450 mm Clear Opening (heavy duty of load bearing capacity 20 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 82 | Providing stitching and hanging three plated curtains made out of curtains cloth of 1.20mtr. wide as per approved sample and shade by folding 100mm at top and 150mm at bottom with all other material like SS rings. thread, buckram, etc. and all labour complete as per direction of Engineer-in-charge. The curtain cloth shall be used of minimum Rs.275/- per mir. and the finished length of curtain shall be measured for payment) Curtain without lining |
| 83 | Refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.(Door will be provided by the department).Of area 3 sq. metres and below |
| 84 | Providing & fixing chicken/ rabbit wire mesh jali fixed with nails, binding wires etc. complete as per direction of Engineer-in-charge. |
| 85 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including Flat 32x5 mm and priming coat with approved steel primer all complete as per direction of Engineer-in-charge |
| 86 | Providing and fixing 6 mm thick toughened glass(Weight not less than 15kg/sqm) for UPVC window / door with necessarary fitting complete as per the architectural drawing , approved brand and manufacture, as per direction of Engineer-in-charge |
| 87 | Providing and Fixing Quartz Stone work (polished and machine cut) of thickness 20 mm for Washbasin Counter, backing filled with pasting araldite adhesive (1.25kg/sqm) including pointing with white cement or matching pigment with an admixture of pigment to match the Quartz shade . Quartz in any colour. Area of slab above 0.50 sqm |
| 88 | Providing and laying chequered precast cement concrete parking tiles 25 mm thick, of approved pattern and shade, size 300×300 mm (or 400×400 mm as directed), manufactured from cement, graded aggregates and pigment, compacted in steel moulds, cured, and laid in true level on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), joints filled with neat cement slurry, finished and cured, including necessary cutting, edge finishing, cleaning and all labour, materials and tools required — complete as per CPWD specifications and as directed by Engineer-in-Charge.” |
| 89 | Providing and fixing 100 mm wide vertical blinds of approved make comparising of rectangular channels with built in gears and clutch system. Louvers made up of approved fabric and both sides of louvers to be supported with elegant noncorrosive ball and chain all complete as per direction of Engineer-in-Charge. |
| 90 | Credit for dismantled Aluminium section etc. which shall be be the proprety of the contractor and should be remove form the site of work as per the directions of the Engineer-in-charge- (Nothing extra shall be paid on account of carriage.) Please Enable Macros to View BoQ information |
