|
| 1 | Dismantling of plain or corrugated steel sheeting any gauge, thicknes, including Naintal or similar pattern roof coverings of any description etc complete all as specified and directed. |
| 2 | Dismantling unframed timber scantling 40 sqm and over in section, in any position complete all as specified and directed. |
| 3 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 4 | Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without taking off shutters from the frame) complete all as specified and directed. |
| 5 | Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters (Without taking off shutters from the frames) complete all as specified and directed. |
| 6 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 7 | S&F 0.63mm thick CGI based Galvanised corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washer, in roofs, walls etc, with grade of zinc coating 275 complete all as specified and directed. |
| 8 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, velly Gutter fixed with self tapping screws complete all as specified and directed. |
| 9 | S&F 1.25mm thick Mild steel sheet, 150mm dia, galvanised class 3, half round with rounded edges complete all as specified and directed. |
| 10 | S&F Steel work in tubular trusses, post, purlin including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st 240 complete all as specified and directed. |
| 11 | M&L for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, pipe, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E 250) quality-A complete all as specified and directed. |
| 12 | S & F solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling fixing in opening as per specification & drawing complete all as specified & directed. |
| 13 | S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 156 of SSR 2010 (Part-II). |
| 14 | S & F of Factory made single extruded WPC (Wood Polymer Composite) solid door/ window /Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extrapayment on this account shall be made. |
| 15 | S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately as per specification. |
| 16 | S&F factory made WPC single extruded 100% lead free ROHS certified board of 18mm thick pre laminated moulded shutter for kitchen, cupboard, the laminated shutter should be pre laminated side with different design and other side plain white of density not less than 600 Kg/cum manufactured by an ISO 9001:2015 certified company, the 18mm board should be 100% lead free , water proof, termite proof and borer proof and should have good screw holding capacity and complete all as specified and directed. |
| 17 | S&F 40mm flap width of continuous (piano) hinges, mild steel bright finish or electrogalvanised complete all as specified and directed. |
| 18 | S&F 40mm cupboards knob fixed with nut Screw and washer of brass polished complete all as specified and directed. |
| 19 | S & F Second class hard wood plain, solid straight chowkhets and frames, wrought, framed rebited on the solid, rounded or chamfered, put together with glues pinned at joints, complete all as specified and directed. |
| 20 | S&F IInd class hard wood, 35mm thick skeleton shutters open rebated & prepared to receive, glass, gauge etc. (without sash bars), edge of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I, Section 8, clause 8.24(a); supplied and fitted to chowkahts. complete all as specified and directed. |
| 21 | S&F IInd hardwood 40 mm thick plain framed pannelled shutter (any number of pannels) with panels of timber flats on bothe sides (feather edged) or of veneered particle board medium density wood particle board with commerical face veneers complete all as specified and directed. |
| 22 | S&F 30mm thick flush shutters solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 23 | S&F 100mm size Stainless steel butt hinges complete all as specifed and directed. |
| 24 | S&F Stainless steel barrel tower bolt 200mm long of extruded section complete all as specified and directed. |
| 25 | S&F Stainless steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed Length of bolt in 250 mm complete all as specified and directed. |
| 26 | S & F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed. |
| 27 | S&F for aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 28 | S& F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed. |
| 29 | M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 30 | M&L for preparation of previously treadted old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed. |
| 31 | Demolition and breaking up drain pipes (Salt glazed ware, PVC/AC or Reinforced concrete) set in cement mortar,and taking out of trenches, if required, Internal dia of pipe in 75MM/100mm/150MM complete all as specified and directed. |
| 32 | S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. |
| 33 | S&F 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, laid in trenches or in floors and jointed complete all as specified and directed. |
| 34 | M&L for PCC 1:3:6 type C-2 (using 40mm grade stone aggregate) as in bed to drain pipe 110/100 mm dia SGSW /PVC pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 35 | S&F 110mm dia PVC (SWR) pipes single/double socketed in any length with rubber ring joints, fixed to walls complete all as specified and directed. |
| 36 | S & F PVC (SWR) bends/sockets any radius 110 mm dia complete all as specified and directed. |
| 37 | S& F stack clamp,110mm/75mm bore made out of 50mm by 5 mm flat iron/pvc and 16 mm dia round stays including bolts and nuts and securing ends of stay to wall or roof complete all as specified and directed. |
| 38 | Hacking out old broken glass of any thicknesssize or description from wooden frames or metal frames fixed with wooden beads/ putty complete all as specified and directed.. |
| 39 | S& F 3 mm thick sheet glass ordinary quality and glazing with oil putty wire clips in square n.exc 0.5 sqm in each pane complete all as specified and directed. |
| 40 | Excavation in post holes (or similar holes) each not exc 0.5 cum getting out, returning filling in and rammin earth or broken rubble mixed with earth around in layers not exc 25 cm watering, and removing surplus soil to a distance not exc 50mtr and making good surface in soft/loose soil complete all as specified and directed. |
| 41 | M & L for PCC 1:4:8, Type D-2 (using 40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 42 | Demolition of brick work or stone boulder masonry built in cement mortar or cement lime including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 43 | M&L for brick work with sub class 'B' bricks built in CM 1:6 straight or curved on plan & exc 6 m mean radius with old size bricks complete all as specified and directed. |
| 44 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:6) and finished even and smooth (without using extra cement) complete all as specified and directed. |
| 45 | M&L for rendering 15mm thick in CM 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 46 | M&L for preparation of new plastered or unplastered surface of walls including cornices, pilasters etc and applying two coats of oil bound distemper over a coat of 3mm thick wall care putty including washing floors, cleaning glass, joinery, electric fittings,wiring etc of drops and splashes and leaving premise, clean and tidy etc complete all as specified and as directed. |
| 47 | M&L for preparation of new plastered or un plastered surface of walls including cornices, pilasters etc and applying two coats of weather proof exterior emulsion paint over a coat of primer complete all as specified and directed. |
| 48 | M&L for preparation of new surfaces of steel and iron work of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint any tint over a coat of red oxide primer complete all as specified and directed. |
| 49 | M&L for preparation of old painted steel surfaces and iron work of any description over 10 cm width or girth not otherwise described and applying one coat (finishing coat) of synthetic enamel paint in any tint complete all as specified and as directed. |
| 50 | M&L for 75mm thick PCC 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection and paving laid in slope finished even and smooth without using extra cement including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight complete all as specified and directed. |
| 51 | M & L for water proofing treatment on RCC roof etc comprising with the following operations and as specified herein below :-(a) Taking down/scrapping out existing old tarfelt bituminous compound including sweeping, cleaning, washing down to remove dust etc and removing debris to a distance n exc 250m. (b) 15mm thick plastering in cement mortar 1:4 mixed with WPC @3% by weight of cement finished even & smooth and curing for minimum 7 days(c) Preparing & Cleaning of fully dried cement plastered surface(d) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per Sqm conforming IS 3384-1986(e) A layer of APP based polymeric membrane 3mm thick (minimum) weighing 3.5 Kg per Sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied over bituminous primer as specified above application of polymeric membrance shall be by torch application. The overlap shall be minium 100mm on transverse direction and 75mm on longitudinal direction complete all as specified and directed. |
| 52 | M & L for one coat of aluminium paint over the APP modified membrane @ 0.11 Kg/sqm complete all as specified and directed. |
| 53 | M&L for PCC (1:3:6) type C-2 using 40mm graded crushed stone aggregate as in foundations, fillings and mass concrete complete all as specified and directed. |
| 54 | S&F MS steel work with angle iron , flat section as in posts and struts in fencing, fillets, plates etc including cutting tops to shape as directed drilling holes, notching for wire etc; including all necessary drilling, bolting or riveting etc; conforming to Fe 290-0 Gde -E-165 complete all as specified and directed. |
| 55 | S & F mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the others or screwed ends each screwed end to be fitted with washers and one hexagonal or square nuts 11 to 15 mm dia of neck, not exceeding 5 cm long complete all as specified and directed. |
| 56 | Supply only chain link fencing MS galvanised fencing any size and not less than 4mm dia complete all as specified and directed. |
| 57 | Fixing only chian link fencing including line wires, any mesh, size and type to any type of standareds, rails, straining bolts etc, including provision of binding wire complete all as specified and directed. |
| 58 | S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standards rails straining bolts,including securing or typing at crossing with and provision of galvanished mild steel wire, stapled or steel pins, etc complete all as specified and directed. (each line of wire to be measured). |
| 59 | M & L for MS round bar, 10mm dia, conforming to Fe 290-0 Gde E-165 as in line wire to chain link fencing complete all as specified. |
| 60 | M & L for preparing new steel surfaces of any description exc 10cm width or girth and applying two coats of black japan paint complete all as specified and directed. |
| 61 | M & L for preparing new steel surfaces of any descripation not exceeding 10cm width or girth and applying, two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified. Please Enable Macros to View BoQ information |
