|
| 1 | M & L for opening of the bobbin wound filter 1200 mm outer diamter by disconnecting the water connections, removing the fastners of manhole covers, checking the internal portion, washing the strainers, taking down/unloading the media from the filters, seiving and stacking of serviceable media in different grading, removing unserviceable filter media to a distance not exceeding 100 m and not exceeding 150ms complete all as specified and directed by Engineer-in-Charge |
| 2 | Supply, laying, packing 1st layer selex media size of 6mm to 8mm as course media of 900 kgs and 2nd layer selex fine media size 2mm to 4mm as fine media of 2100 kgs complete all as specified and directed by Engineer-in-Charge |
| 3 | Material and labour for opening the 3 phase, 7.5 to 10 HP, 415 V electric motor carefully removing all burnt/wornout coils by cutting, cleaning the slots and re-winding of electrical motor with super enameled copper winding wire of required gauge and suitable size by providing necessary insulating material, baking, varnishing etc including painting with two coats of painting over one coat of red oxide primer and testing the smooth running of motor on full load for 8 hours continuously complete all as specified and directed by Engineer-in-Chage |
| 4 | M&L for disconnecting electrically operated monoblock centrifugal pump set, 3 Ph, 7.5 to 10 HP and taking out from foundation for repair, transporting to workshop for repair and assembling the same after repair, transporting back to site, refixing recommissioning and testing of complete including necessary nuts & bolts for pumpset to the entire satisfaction of Engineer-in-Charge as directed.Note : Spare parts will be measured and paid for separately as supply only. Cost of labour for replacement of parts shall be deemed to include in the rate quoted for this item. All the repair work should be completed within 48 hours, to made functional swimming pool. |
| 5 | Supply only following spare part against Item No 4.00 above suitable for 7.5 to 10 HP Pump Set 3 Phase capacity monoblock pump sets complete all as directed by Engineer-in-charge. |
| 6 | (a) CI Impeller |
| 7 | (b) Impeller nut GM |
| 8 | (c) key for Impeller MS |
| 9 | (d) Front bearing |
| 10 | (e) CI front inner cap. |
| 11 | (f) CI rear inner cap. |
| 12 | (g) Rear bearing |
| 13 | (h) CI rear outer cap. |
| 14 | (j) Terminal board bakelite |
| 15 | Supply and fixing gland pack of pump set 7.5 to 10 HP capacity complete all as specified and directed by Engineer-in-Charge |
| 16 | M&L for taking out old unserviceable ball bearing of 7.5 to10 HP capacity electric motor and supply and fixing of new ball bearing of suitable size and make, making proper alignment and testing all as specified and as directed by Engineer-in-Chage. |
| 17 | S&F gland and packing the sluice valve in existing pipe line including removal of old gland material and replacing Nails and belts etc for cast iron pipe of any sizes including taking out old joint complete all as specified and directed by Engineer-in-Charge. |
| 18 | M&L for taking out suction sweeper from swimming pool, dismantling for inspection and renewal/replacement of UNSV parts and reassembling the suction sweeper of 2-3 feet complete all as specified and directed by Engineer-in-Charge.Note : Spare parts will be measured and paid for separately as supply only. Cost of labour for replacement of parts shall be deemed to include in the rate quoted for this item. |
| 19 | Supply only wooden base PVC strip brushes length of 2-3 feet, bristle length, bristles of length 7cm and 1mm dia, medium stiffness, made of polypropylene with polyster bristle for cleaning of swimming pool floor/walls complete all as specified and directed by Engineer-in-Charge. |
| 20 | Supply only vaccum PVC nylon flexible hose pipe 50/40 mm outer dia heavy duty, floating green ribbed colour complete all as specified and directed by Engineer-in-Charge. |
| 21 | Supply only vaccum PVC nylon flexible hose pipe 63 mm outer dia heavy duty, floating green ribbed colour complete all as specified and directed by Engineer-in-Charge. |
| 22 | Supply only rubber packing for suction sweeper of 2-3 feet as per existing size including MS nuts, bolts, washers, studs etc as required at site complete all as specified and directed by Engineer-in-Charge. |
| 23 | Supply and fixing in repair wheel of suction sweeper pump as per existing suitable size, as per sample and taking out old UNSV complete all as specified and directed by Engineer-in-Charge |
| 24 | Supply only Nylon rope for suction sweeper as per existing size upto 25mm dia complete all as specified and directed by Engineer-in-Charge. |
| 25 | M&L dewatering, cleaning of balancing tank of capacity 50000 gallons remove all mosses, algae and dirt and removal of dirty water along with sludge by suction pumps and disposal of the same to a safe distance including scrubing of internal surface by steel wire brush, removing the dirt completely and sterilizing the complete internal surface of the tank by using ISI mark Gd I bleaching powder including repair to vent pipes and providing wire mesh and clamps (to stop ingress of pigeons) complete and marking the date of cleaning by using synthetic enamel paint in white colour over black background and letters of height 40 mm height and 30 mm width complete all as directed including one coat of white wash on the internal surface complete all as specified and directed by Engineer-in-charge.Note:Outer surface of balancing tank painted one layer of OBD over existing . Neccessary tools and safety gears to be arranged by contractor without any extra cost. Labours safety shall be contractors responsiblity. |
| 26 | Supply and painting one coat of existing colour to horizontal bobbin wound filter of any Size complete all as specified and directed by Engineer-in-Charge. |
| 27 | Material and labour for repairing Membrane Dosing pumps \\"EXACTUS\\" model. Electronic dosing pump all as specified and directed by Engineer in Charge |
| 28 | Supply and fixing in repair Main drian (Pool Drain) grating in SS 304 grade, complete of suitable size 500 x 500 mm complete with all relative fitting and making good, as per AISI 304, EN 13451 standard, maximum flow up to 136 m3/Hr complete all as specified and directed by Engineer-in-charge. |
| 29 | Supply and fixing in repair suction inlet in ABS with cap internal thread of 1.5\\" (1.5 inch) dia and external thread 2\\" (2 inch) complete all as specified and as directed by Engineer-in-Chage |
| 30 | Supply and fixing in repair floor inlets of white ABS plastic bottom inlet for concrete with SS screws and regulable etc complete all as specified and as directed. |
| 31 | Supply and fixing in repair of PVC butterfly Valve of dia 110 mm PN 10 including rubber gaskets complete all as specified and directedby Engineer-in-Charge |
| 32 | Supply and fixing in repair of PVC butterfly Valve of dia 160 mm PN 10 complete including rubber gaskets all as specified and directedby Engineer-in-Charge |
| 33 | Supply and fixing in repair PVC flange and adapter 10 kg/cm2 for 110 mm including rubber gaskets complete all as specified and directed by Engineer-in-Charge |
| 34 | Supply and fixing in repair PVC flange and adapter 10 kg/cm2 for 160 mm including rubber gaskets complete all as specified and directed by Engineer-in-Charge |
| 35 | Supply and fixing in repair PVC Wafer Check Valve Dia 110mm PN 10 including rubber gaskets complete all as specified and directed by Engineer-in-Charge |
| 36 | Supply and fixing in repair PVC Wafer Check Valve Dia 160 mm PN 10 including rubber gaskets complete all as specified and directed by Engineer-in-Charge |
| 37 | M&L for opening the end of 'Y' strainer and replacing the internal mesh filter (screen) inclduing taking down old mess filter and fixing the end the cap including rubber gaskets complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply only Test kit for free chlorine & pH as per cat No. 01419 of Make-Astral or techno commercial equvivalent of Hayward/Leisure pool/Techpool/Certikin swimming pool product India pvt. Ltd./ION Exchange (India) ltd. |
| 39 | Supply only Transparent blue plastic vacuum hose 2\\" (2 inch) dia 30 mtrs long including hose cuffs for connection to suction inlets complete all as specified and directedby Engineer-in-Charge |
| 40 | Supply only Deep bag net made in polypropelene and white polyester netting shark complete all as specified and directed by Engineer-in-Charge |
| 41 | Supply only Surface net made in polypropelene and white polyester netting Shark complete all as specified and directed by Engineer-in-Charge |
| 42 | Supply only Curved brushes made in polypropelene for pool basins and scum liners complete all as specified and directed by Engineer-in-Charge |
| 43 | Supply only Straight brushes made in polypropelene for pool basins and scum liners complete all as specified and directed by Engineer-in-Charge |
| 44 | Supply only Life Buoy ring of HDPE filled with PU foam outer diameter 72 cm inner diameter 43 cm thickness around 95-115 mm weight 2.5 kg to 4.3 kg, buoyancy around 145 N (for 2.5kg) or 165 N (for 2.8kg) complete all as specified and directed by Engineer-in-Charge |
| 45 | Supply only Life Jacket Polyester Fabric with EPE Foam for Adult Safety Jacket along with Whistle for Swimming, Boating, Floating- Weight Capacity Upto 125 Kg complete all as specified and directed by Engineer-in-Charge |
| 46 | Supply only vaccum head aluminium 18\\" anodised vaccum head with bottom brush complete all as specified and directed |
| 47 | Supply only Extensible handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf skimmers and scoops.10.0 mts. with handle adapter complete all as specified and directed by Engineer-in-Charge |
| 48 | Supply and laying and testing uPVC pipes of min 10Kg/sq.cm pressure rating including all required fittings with solvent welded joints along with necessary fittings, supports & hanger complete all as specified and directed for 63 mm outer dia complete all as specified and directed by Engineer-in-Charge. |
| 49 | Supply and laying and testing uPVC pipes of min 10Kg/sq.cm pressure rating including all required fittings with solvent welded joints along with necessary fittings, supports & hanger complete all as specified and directed for 110 mm outer dia complete all as specified and directed by Engineer-in-Charge. |
| 50 | Supply and laying and testing uPVC pipes of min 10Kg/sq.cm pressure rating including all required fittings with solvent welded joints along with necessary fittings, supports & hanger complete all as specified and directed for 160 mm outer dia complete all as specified and directed by Engineer-in-Charge. |
| 51 | Supply and fixing in repair high quality 160mm UPVC water pipe fitting foot valve with flange end including replacement of nuts, bolts and washers complete all as specified and directed by Engineer-in-Charge. |
| 52 | S&F in repair Power contractor assembly for 10 HP motor pump complete as per existing type and make including taking down old contactor complete all as specified and directed by Engineer-in-Charge. |
| 53 | S&F in repair Thermal Overload relay range 11-16 amps as per existing make suitable for upto 10 HP motor/pump complete all as specified and directed by Engineer-in-Charge. |
| 54 | S&F in repair Electronic timer for star delta function having time range 3-60 sec, input voltage 380-440V AC or as per existing make and model including talking down of old one complete all as specified and directed by Engineer-in-Charge. |
| 55 | S&F in repair indicator lamp assembly set complete LED type suitable for the existing system supply Voltage 230V/440 V AC including taking down old lamp assembly complete all as specified and directed by Engineer-in-Charge. |
| 56 | S&F in repair Push button assembly complete LED type sultable for the existing system supply voltage 230V/440V AC Including taking down push button assembly complete all as specified and directed by Engineer-in-Charge. |
| 57 | Supply and fixing 415V 10 KA 'C' curve miniature circuit breaker TP 63 Amps (MCB) suitable for fixing on panel complete all as specified and directed by Engineer-in-Charge. |
| 58 | S & F MCCB 4P 415 volts 35 KA suitable for fixing on panel of capacity 200 Amps with extended terminals complete all as specified. Note:- (i) Suitable size and frame of MCCB required as per existing panel at site.(ii) MCCB Rating ICS=100 % ICU all as specified and directed |
| 59 | S & F in repair digital type voltmeter to display voltage 0-500 voltage suitable for three phase 4 wire system complete all as specified and directed by Engineer-in-Charge. |
| 60 | S & F in repair digital type ammeter to display current 0-100 amp suitable for three phase 4 wire system all as specified and directed |
| 61 | S & F in repair selector switch as per existing all as specified and directed |
| 62 | M&L for Taking down of single Headed Oblique type gun metal fire hydrant valve 63 mm dia complete all as specified and directed. |
| 63 | S&F in replacement of ISI marked single headed 63 mm dia. gun metal Hydrant Valve, flanged inlet with 63 mm female instantaneous outlet confirming to IS : 5290 on the fire wet riser/down comer including making 80 NB pipe connection with riser fixing the landing valves in proper positions, including supply of nuts, bolts, gaskets, caps, chains etc. testing the hydrant and completing the work in all respect all as specified and directed. |
| 64 | S&F gun metal ISI marked 63 MM. dia. Instantaneous pattern short branch pipes & 12.5 mm dia. Nozzle suitable for inter connections to hose pipe coupling as required complete all as specified and directed. |
| 65 | S&F in replacement Outlet nozzle cap along with chain fixed on hydrant 63mm as required complete all as specified and directed. |
| 66 | Taking down of Female Adaptor gun metal for fire hydrant valve 63 mm dia complete all as specified and directed by Engineer-in-Charge. |
| 67 | Supply and replacement of female adaptor (Gun metal) suitable for 63 mm dia fire Oblique type fire hydrant valve complete all as specified and directed by Engineer-in-Charge. |
| 68 | M&L for Red colour Painting on Fire hydrant Pipe of dia 80 mm/100mm/150 mm by scrapping the old surface and applying two coat of synthetic enamel paint on the surface and making good any disturbed surface complete all as specified and directed by Engineer-in-Charge. |
| 69 | Servicing of valve any type and size opening greasing running part required new gland fitting and reassemble again complete all as specified and directed.Note : Items required for replacement shall be measured and paid seperately |
| 70 | Supply and apply Grease of Suitable Grade complete all as specified and directed by Engineer-in-Charge. |
| 71 | S&F Gland of suitable size complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 72 | S&F Gland of suitable size complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
