|
| 1 | Gypsum Partition:Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. |
| 2 | The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board with BIS certification marks)(Note: The Vertical Frames Members will be extended upto ceiling height to fasten/ Strenthen the Partition Work.) |
| 3 | Rock WOOL Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS: 8183, having density 48 kg/m3 , 50 mm thick,wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held and in position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge. |
| 4 | (Providing & fixing of 12 mm toughened glass door): Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 5 | (Film on glass door):Providing & fixing translucent film (Make : 3m) on glass of approved quality & make and as per the direction of Engineer-in-charge. |
| 6 | (Door Lock ):Providing and fixing Door Lock Double open dead lock type of Hafele, Ozone make for glass door shutter of approved quality & make and as per the direction of Engineer-in-charge(Make :- Hafele, Ozone) |
| 7 | (SS H-type Handle):Providing and fixing Stainless steel Handle for glass door shutter of approved quality & make and as per the direction of Engineer-in-charge.Make :- Hafele , Ozone Size of handle :- 400 mm, dia 25 mm |
| 8 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with doublespring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floorfinishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.With stainless steel cover plate minimum 1.25 mm thicknessMake :- Hafele , Ozone |
| 9 | Putty:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.Make :- JK Putty/Birla |
| 10 | Paint:Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.(Make :- Asian paint-Royale Luxury Emulsion Shyne/Dulux Paint-Velvet Touch) |
| 11 | Paint:Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) as required at walls. (Make:- Asian-Apex Ultima /Dulux Paint- Weather Shield) |
| 12 | Providing and fixing 12 mm thick Medium Density Fibreboard (MDF) board, both sides pre-laminated, conforming to IS:14587–2023, Grade-2, Type-3, with BIS certification marking on board including approved make of hardware fittings and accessories, all complete as per engineer in charge.(Make:- Century/Action Tesa) |
| 13 | Aluminium Work:- Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections ofapproved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete and as directed by Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 14 | Glass:- Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 15 | Providing and fixing of split AC 1.8T/ 1.65T with 5 star inverter including outdoor and indoor units by cutting the grooves in wall, insulation material, 3.00 mt copper pipe and drain pipe as required.Gas-R-32, Split AC, 230 volt, Noise level-32 Decibels,Air flow efficiency-635 cuft/min/wattwarranty of compressor:- 10 years warranty of PCB:- 05 yearsMake :- Daiken, Mitsubishi, O General as approved by Engineer-in-charge.Model NO. FTKM60UV16U (Daiken), SRK18YX52-W6 (Mitsubishi)Note:- The invoice of the material shall be submitted to IIM Indore after completion of the work. |
| 16 | Enamel paint:-Painting with synthetic enamel paint (at all height) of approved brand and manufacture of required colour to give an even shade : One or more coats on old work including removing of the old paint.(Make:- Asian/ Burger) |
| 17 | Scrapping:- Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 18 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 19 | WC:- Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of CAT No. C8971 of Parryware/ CAT No.92563 of Hindware make shape, size (700x425x770mm) including integrated white vitreous china cistern of capacity 9 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 20 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of make CAT No. C0599 of Parryware/ CAT No.60021 of Hindware of size 365x370x550mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
| 21 | Providing and fixing vessel type wash basin without deck, white colour, Kohler Make Model No. K-38520IN-0 or equivalent with required bathroom sink grid drain without overflow, Model No. K-75823IN-CP, and CP brass bottle trap of 350 mm projection, Model No. K-20746IN-CP, of Kohler or as specified in the approved make list Kohler/Grohe / Toto), complete.The work shall also include all necessary fixing accessories, rubber washers, sealing materials, alignment, testing, cutting and making good the openings wherever required, complete in all respects as per specifications and direction of the Engineer-in-Charge. |
| 22 | Providing and fixing health faucet, Premium Hygiene Spray with 1.2 meter long easy SS Flexibe Metal Hose and Holder (Chrome Finish) of Kohler - CAT no. 98100IN-CP make or as specified in the approved make list (Groho / Toto), including all requisite fittings and making good the openings wherever required all complete job & as per the direction of Engineer-in-charge |
| 23 | Providing and fixing toilet paper holder, wall mounted type, made of C.P. brass, of Kohler make, CAT No. K-5633IN-CP or as specified in the approved make list (Groho / Toto) make, complete with all necessary fixing accessories such as screws, wall plugs and brackets, including making good the wall surface wherever required, all complete as per manufacturer’s specifications and direction of the Engineer-in-Charge. |
| 24 | Providing and fixing mirror of superior glass (of approved make: Saint Gobain/ Asahi) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape (This Includs any fittings/ Fixtures required to fix the mirror). |
| 25 | Supply & fixing of 300 ml manually operated wall mounted top push soap dispenser of Approved sample of Make/ Model: Hindware CAT No. F102018 / Parryware CAT No.- T6913A1 glass with SS holder and made up of ABS transparent/ semi transparent plastic including necessary fixing arrangements etc. all complete as per the direction of Engineer-in-Charge. |
| 26 | Providing and fixing SWR moulded / uPVC self-cleansing type Nahani trap / floor trap of Ruhe make or equivalent approved make with minimum 50 mm water seal, including integral anticockroach arrangement, connecting to waste pipe, cutting and making good the walls and floors, waterproof grouting of joints, sealing with approved sealant, providing necessary support/encasing in PCC as required, complete as per directions of Engineer-in-Charge, including providing and fixing stainless steel (SS 304) square floor drain jali of size (5\\" × 5\\") complete in all respects. |
| 27 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over and jointed with Adhesive chemical including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. |
| 28 | Area of slab upto 0.50 sqm |
| 29 | Area of slab Over 0.50 sqm |
| 30 | Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. |
| 31 | Providing and laying 15 mm white Glossy Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with chemical adhesive Laticrete as per manufacturer specification including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of sizeWhite glossy tile (Make:- Somany/Kajaria) |
| 32 | Providing & Fixing of two way bib cock of Kohler make (CAT No. K-25432IN-4-CP) as specified in the approved make list (Groho / Toto) in polished chrome all complete as per direction of Engineer-in-Charge |
| 33 | Kota stone slab of 25mm Thickness laid over and jointed with Adhesive chemical for kota stone of approved quality including rubbing and polishing complete. |
| 34 | Dismantling W.C. Pan/urinal basin/ wash basin of all sizes including disposal of dismantled materials i/c malba all complete to be shifted upto 2.0 km within the IIM campus as per directions of Engineer in Charge. |
| 35 | Providing and fixing C.P. brass angular stop cock 2-in-1 (advance type), 15 mm nominal bore, in polished chrome finish, CAT No. F690044CP of Hindware make or equivalent approved make, complete with all necessary fittings, fixing accessories, testing and commissioning, all complete as per the direction of the Engineer-in-Charge. |
| 36 | Supply and installation of Brass Extended Tall Body Pillar Cock Tap for wash basin, chrome finish, including necessary fittings, testing, and commissioning as per site requirement and as directed by engineer-in-charge (Make:-Jaguar/Hindware) |
| 37 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S, including cost of adhesive of approved quality,cutting space for switchboard & rubbing existing surface.(Including scratching the Bottom surface of the Existing Table for Proper Adheshion)1mm Thick approved make (Greenlam, CenturyPly, Kitply) |
| 38 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 39 | Windows:- Factory made complete set with glass fitting of aluminium track- 3 TRACK with 3 SHUTTERS (Domal Section-) : Providing & fixing of customized sliding window upon granite platform at base as per site dimensions & shade of Jindal aluminum/Hindalco section with approved design of minimum 40 micron Anodized, Series of - (27 mmx65 mmx1.5mm thick with frame) shall have 5mm Plain glass sliding of saint gobain or asahi make with all necessary EPDM gasket, 6mm thick, Wool-pile & accessories like steel body roller bearing with capacity of 50-60kg for smooth sliding, adequate size Metal-body/Plastic-body Star-lock make concealed lock, drain hole, sealing of frame and wall opening by joint backing cord and sealant, etc. in complete. Note-A factory detail/profile has to be provided & may be visited if required & approved by IIM. The sizes of windows shall be taken by the vendor and customize accordingly as per existing opening in houses.Note:- (Glass measurement shall be Paid Separately.)(Only fitting at site with dash fastners) at ground and First floor level including escaffolding. |
| 40 | Louvers- For Toilet : Providing & fixing aluminum 40 micron powder coated louvered as per site dimension with Series- (18mmx40mmx1mm) thick aluminum pipe frame work with 8\\"x 8\\" cut-out for exhaust-fan provision actuating bar with glass holder, locking handle 5mm frosted glass etc. in complete, including mosquito net to be fixed from outside to the louver glass part to protect insect coming as approved. |
| 41 | Providing & Fixing of flush door shutter (WPC) to the existing frame using stainless steel hinges , including necessary screws, adjustments, and alignment, as per the instructions of the Engineer-in-Charge. |
| 42 | Exhaust Fan:- Supply & Installation of exhaust fan with including additional accessories of approved brand, all as per the direction of Engineer-in-charge.DX 150mm12.6D x 24.1W x 24.1H Centimeters |
| 43 | Roller Blinds:- Supply & Installation of Roller Blinds Translucent as per direction of the engineer in charge.Technical SpecificationsPattern & Colour - as approved by Engineer-in-charge.Composition - 100% PolyesterCoating:- Translucent Fabric Thickness +/- 5%:- 0.05mmFabric Weight 400 gsm +/- 5% EPI/PPI:- 178/66Care Instruction - Spongable (Fire Classification - NFPA 701-200+TN#1)Mechanism Specifications - Tube diameter not less than 43 mm diameter with stabilizer profiles inside. Manual control via pvc thread operated open/close system. Fixed to walls with bracket. Powder coated Aluminium bottom bar with caps on both ends.Load capacity - Minimum 2 Kg/linear meter(Make- Johnson Blinds, Vista (Black out Venice) |
| 44 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 45 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mmNote: If the tiles are laid on the surface using chemicals as per Item No. 43, the amount of 20 mm cement mortar shall be deducted accordingly. |
| 46 | Providing & Fixing of Adhesive chemical for Vitrified Tiles of approved quality & make and as per the direction of Engineer-in-charge.Make - MYK LATICRETE 315plus premium tile Adhesive Please Enable Macros to View BoQ information |
