|
| 1 | NS Item -XOXO PANEL Main Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked 151239 Minimum 114 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. A. Play panel LLDPE (Linear Low-Density Polyethylene), roto-moulded Thickness: 6-8 mm wall thickness. Finish Seamless, anti-static, smooth surface UV Resistance. Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps on exposed bolts. Surface Coating Primer: Epoxy zinc-rich primer (40 microns) Top Coat: Outdoor polyester powder (60-80 microns) Adhesion: 5B rating (ASTM D3359) Color Options: Custom RAL shades,UV-stabilized Safety Compliance Standards: EN 1176(Europe) ASTM F1487 (USA)Fall Height: Compliant up to 2.5 meters Surfacing (optional): Prevention No head, neck, or finger entrapment zones Edge Protection: Rounded corners, no sharp edges. Installation: RCC blocks or anchor bolts with M 20 grouting Installation. Certified team with adherence to manufacturer`s layout Tools and Hardware: Supplied with the product Site Preparation: Level ground, drainage recommended |
| 2 | NS Item --SIT N SNICKER SWINGMain Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primerplus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh PowerMachine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239Minimum 40 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zine primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bendingwith fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.. Bending with fully automatic Pipe Bending Machine, Welding WithLaser Welding Heigh Power Machine.Wheel Chair Safety Door: CR sheet (1.6-2.0 mm thick) Manufacturing: CNC laser-cut with anti-slip perforated texture Finish: Hot-dip galvanized plus powder coatingLoad Capacity: Minimum 150 kg per platform.Swing Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60-80 microns),Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Car Shaped Side Panel: designed to provide shade and aesthetic appeal toplayground structures. Crafted from durable 3 layer HDPE sheets 20 mm thik and precision router-cut.Pins: are made up of M.S bright bar. Bearing bushes: 089mm OD seamless pipe.Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic.Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic safety caps |
| 3 | NS Item -MERRY-GO-ADAPT Main Structure Material: Galvanise Steel (GI)ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer outdoor grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine, Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 40 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primer plus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine... Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6-2.0 mm thick) Manufacturing: CNC laser-cut with anti-slip perforated texture Finish: Hot-dip galvanized |
| 4 | NS Item -Wheelchair Providing and supplying standard manuall wheelchair made of high-quality powder-coated/mikt steel tubular chair shall be foldable type for easy storage and portability.Technical Specifications: me: Mild Steel/Aluminum, powder-coated finish Width: Approx. 18 inches (450 mm), made of durable, washable canvas or PVC crest: Fixed/Foldable reinforced support Whods: Rear wheels: 24 solidrubber with hand for selfpropelling Front wheels: 8 PU/solid rubber caster wheelsArmrests: Fixed or flip-up cushioned armrests Brakes: Manual parking brakes on both rear wheels heel support Foldable Design: For convenient storage and transportation Warranty: Minimum 1 year against manufacturing defect |
| 5 | NS Item -CHEERFUL CHURNMain Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS1239 Minimum 90 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primerplus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh PowerMachine., Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine.Support Structure Material: Galvanise Steel (GI) ERW Pipes ISI Marked IS 1239 Minimum 40 mm outer diameter (OD), 2.0-3.0 mm thickness Surface Finish Zinc primerplus outdoor-grade polyester powder coating (min. 60-80 microns), Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh PowerMachine., Bending with fully automaticPipe Bending Machine, Welding With Laser Welding Heigh Power Machine. Wheel Chair Safety Door: CR sheet (1.6-2.0 mm thick) Manufacturing: CNC laser-cut withanti-slip perforated texture Finish: Hot-dip galvanized plus powder coating Load Capacity: Minimum 150 kg per platform. mgr Base Material: Checker Sheet 3mm Process with CNC Laser Machine, Surface Finish Zinc primer outdoor-grade polyester powder coating (min. 60-80 microns),Bending with fully automatic Pipe Bending Machine, Welding With Laser Welding Heigh Power Machine., Bending with fully automatic Pipe Bending Machine, WeldingWith Laser Welding HeighPower Machine Car Shaped Side Panel: designed to provide shade and aesthetic appeal to playground structures. Crafted from durable 3 layer HDPE sheets 20 mm thikand precision router-cut. Pins: are made up of M.S bright bar. Bearing bushes: 089mm OD seamless pipe.Clamps and Connectors Material: Die-cast aluminium or aluminium alloy Finish: Natural anodized or powder coated Properties: Anti-rust, tamper-resistant, non-toxic.Fasteners Material: Galvanized Iron (GI), zinc-coated Type: Tamper-proof bolts and nuts Rust Resistance: Min. 500 hours salt spray test protection: Plastic |
| 6 | HSR Item 10.29.2-Providing and laying of chequered terrazzo tiles 20 to 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : 2. Medium shade pigment using 50% white cement, 50% ordinary cementHSR Rate(Rs.) 793.00 Through Rate |
| 7 | HSR Item 4.14.1-Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. All kinds of soil.HSR Rate(Rs.) 83.00 Through Rate |
| 8 | HSR Item 6.39.1-Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. 1. 1:1½:3 (1 Cement: 1½ coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).HSR Rate(Rs.) 4135.00 Through Rate |
| 9 | HSR Item 13.41-Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).HSR Rate(Rs.) 396.00 Through Rate |
| 10 | HSR Item 10.100.2-Cement Concrete 1:8:16 Flooring 2. Cement Concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth.HSR Rate(Rs.) 1863.00 Through Rate |
| 11 | HSR Item 13.29.2-Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 2. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksHSR Rate(Rs.) 83.00 Through Rate |
| 12 | HSR Item 26.83-Providing and fixing of Tuflex Garden fencing Hexagonal net/ or equivalent of green colour having contents Weight grams /sqm 510( plus /-8%) in width of 60cm. With bamboo of 90 cm Length and 18-20 cm in girth . The bamboo should be painted with green colour, 1st quality and of approved brand and manufacture two or more coats and fixed 30cm below ground level and 60cm above ground level at a distance of 1.50 metres. The net and bamboo complete and as per direction of Engineer- In- charge.HSR Rate(Rs.) 147.00 Through Rate |
| 13 | HSR Item 11.72.2-Painting with silicon and acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces :2. Two coatsHSR Rate(Rs.) 61.00 Through Rate |
| 14 | HSR Item 4.33-Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 1 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.HSR Rate(Rs.) 138.00 Through Rate |
| 15 | HSR Item 26.76-Providing and fixing pair of Plastic dustbins 100 litre volume each, of two different colours, for dry and wet waste, made of virgin plastic to be mounted on MS rectangular hollow section 50 x 25 x 3 mm frames pivoted on 3 MS square hollow section verticals, 1 m above ground, one 35 cm RHS welded to each vertical member at base and grouted in 180 x 40 x 30 cm 1:2:4 cement concrete.HSR Rate(Rs.) 10666.00 Through Rate |
| 16 | HSR Item 6.1.2-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 2. 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)HSR Rate(Rs.) 3476.00 Through Rate |
| 17 | HSR Item 34.29.2-GI barbed wire fencing 2. G.I Barbed Wire Fencing 1.8 Metre HighProviding and fixing 1.8 metres high GI barbed wire fencing with 2.4 m angle iron posts 50 mm x 50 mm x 6 mm placed every 3 metres centre to centre founded in M15 grade cement concrete, 0.6 metre below ground level, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with 12 horizontal lines and 2 diagonals interwoven with horizontal wires, fixed with GI staples, turn buckles etc complete as per clause 807HSR Rate(Rs.) 435.00 Through Rate |
| 18 | HSR Item 34.10.1-Informatory sign board 600x600 rectangular as per IRC 67- 2012 with retro reflective Sheeting as per ASTM D 4956 09 and as per IRC 67 2012 fixed over 3 mm thick aluminium Composite material (ACM) sheeting having aluminium skin thickness of 0.4 to 0.5 mm on both sided and fixing the same with suitable size aluminium alloy rivets @ 200 mm c/c to back support frame of 25x25x3mm angle iron supported on a square hollow steel section post 60x60x3.2mm conforming to IS 4923 without cost of definition plate firmly fixed to ground in foundation concrete M-25 of size 0.45x0.45x0.75m for vertical post complete as per clause 801 of MORTandH specifications. Supplier shall provide a warranty as per clause 6.9 of IRC 67-2012 for retro reflective sheeting and a certified copy of test reports from an independent test laboratory including three year outdoor weathering test report for sheeting tested in India condition conforming to clause 6.7 of IRC 67-2012 1. Using retro reflective Sheeting Class C as per IRC 67 2012HSR Rate(Rs.) 4097.00 Through Rate |
| 19 | HSR Item 11.82.1-Painting the wooden / metal surface with synthetic enamel paint of approved brand and manufacture to give an even shade : 1. Two or more coats on new workHSR Rate(Rs.) 49.00 Through Rate |
| 20 | HSR Item 10.107-Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes and patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. 0 0 0HSR Rate(Rs.) 1605.00 Through Rate |
| 21 | HSR Item 3.1.2-By Mechanical Transport including loading, unloading and stacking 2. EarthHSR Rate(Rs.) 83.00 5km |
| 22 | HSR Item 26.58.3-Supply and installation of garden bench 3. Cast Iron bench of 1800 mm length, 900 mm width, 450 mm seating height, sides made of cast iron. Seat and back shall be made of 10 strips of M.S. pipes 63 mm x 25 mm of 14 gauge with one M.S. Flat 25 x 10 mm welded at the centre, below and back of the seat and back rest. Spray painted with approved brand paint. Fixed by grouting with 1:2:4 cement concrete (Minimum weight of each bench 105 kg). All materials required to be as per BIS specifications.HSR Rate(Rs.) 11438.00 Through Rate |
| 23 | HSR Item 13.30.1-Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 1. Hot finished welded type tubesHSR Rate(Rs.) 105.00 Through Rate Please Enable Macros to View BoQ information |
