|
| 1 | Item Rate BoQ BoQ_Ver3.0 Item Rate Normal INR Only INR Select, Excess (+), Less (-) Less (-) Tender Inviting Authority: GE Utilities Udhampur Name of Work:Repair/Replacement of pumping system, LT Switchgear, pipe line and associated control valves at various pump house, MAP Accn, Md Accn and OTM’s in Garhi Cantt area under GE Utilities Udhampur Contract No: GE/U-02/2026-27 Bidder Name : PRICE SCHEDULE(This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only ) NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # Ser.No. Item Description Item Code / Make Quantity Units Estimated Rate Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency BASIC RATE In Figures To be entered by the Bidder Rs. P Excise Duty VAT Freight Charges ( Unloading & Stacking) Any Other Taxes/Duties/Levies Other Taxes 2 IIIrd Party i.e DGS&D / RITES etc Inspection Charges @0.34%+Service Tax Less for Cenvat Credit,if any respect of Supplies Under full Excise Duty Category TOTAL AMOUNT Without Taxes TOTAL AMOUNT TOTAL AMOUNT In Words |
| 2 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth,foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. and taking out/laying of pipe lines of soft/loose soil, complete all as specified and directed by Engr-in-Charge. |
| 3 | Returning, filling in, including spreading, leveling, watering and well ramming in layers, each layer not exceeding 25cm thick after pipes have been laid and tested, complete all as specified and directed by Engineer-in-Charge |
| 4 | Removing excavated material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed by Engineer-in-Charge |
| 5 | Taking up or down old unseviceable GI pipe of size 100 mm dia including all fittings, complete all as specified and directed by Engineer-in-Charge |
| 6 | Description all as per ser item No 4.00 here-in-before but size of 80 mm dia |
| 7 | Taking up or down old unseviceable GI pipe of size 50 mm dia including all fittings, complete all as specified and directed by Engineer-in-Charge |
| 8 | Description all as per ser item No 6.00 here-in-before but size of 40 mm dia |
| 9 | Description all as per ser item No 6.00 here-in-before but size of 25 mm dia |
| 10 | Description all as per ser item No 6.00 here-in-before but size of 20 mm dia |
| 11 | Description all as per ser item No 6.00 here-in-before but size of 15 mm dia |
| 12 | Supply & fixing GI pipes of size 100 mm dia, medium grade, galvanized with all fitting such as bends, tees, nipples, union and sockets, clamps etc laid in trenches, under floor/along walls etc, complete all as specified and directed by Engr-in-Charge. |
| 13 | Description all as per ser item No 11.00 here-in-before but size of 80 mm dia |
| 14 | Description all as per ser item No 11.00 here-in-before but of 50 mm dia |
| 15 | Description all as per ser item No 11.00 here-in-before but of 40 mm dia |
| 16 | Description all as per ser item No 11.00 here-in-before but of 25 mm dia |
| 17 | Description all as per ser item No 11.00 here-in-before but of 20 mm dia |
| 18 | Description all as per ser item No 11.00 here-in-before but of 15 mm dia |
| 19 | Supply and fix in replacement cast iron sluice valve suitable of size 150 mm (PN 1.6) as per IS : 14846 with iron wheel head both end flanged, non rising type and jointing with the rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers including taking down the old existing,complete all as specified and directed by Engr-in-Charge. |
| 20 | Description all as per ser item No 18.00 here-in-before but of size 100 mm dia |
| 21 | Description all as per ser item No 18.00 here-in-before but of size 80 mm dia |
| 22 | Supply and fix in replacement of cast iron non return valve suitable for 150 mm bore pipe heavy duty both end flanged of pressure rating PN 1.6 as per IS:5312 and jointing with the rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers including taking down the old existing,Complete all as specified and directed by Engr-in-Charge. |
| 23 | Description all as per ser item No 21.00 here-in-before but of size 100 mm dia. |
| 24 | Description all as per ser item No 18.00 here-in-before but of size 80 mm dia. |
| 25 | Supply and fix in replacement of cast iron air release valve with two air outlets of size 100 mm dia as per IS 14845 including all jointing materials like high pressure rubber gasket nuts, bolts, washers with arrangement for fixing, including taking down complete,complete all as specified and directed by Engr-in-Charge. |
| 26 | Description all as per ser item No 24.00 here-in-before but of size 80 mm dia. |
| 27 | Decoupling, disconnecting sluice valve of size 150 mm dia, taking down from pipe line, opening all parts for refacing, regrinding and refixing at its original location including replacement of unsv parts, cleaning, repacking stuffing box of sluice valve and spindle including fixing and testing complete all as directed.Note :- (i) Loading/unloading & transportation charges shall be deemed included in the quoted rates.(ii) S&F of spare parts shall be measured and paid separately under respective items:- |
| 28 | Replacement of Hand wheel |
| 29 | Replacement of SS Stem & GM Nut |
| 30 | Replacement of Cap |
| 31 | Replacement of Flange Rubber Gasket |
| 32 | Replacement of Nut & Bolt + 2 Washers |
| 33 | Decoupling, disconnecting sluice valve of size 100 mm dia, taking down from pipe line, opening all parts for refacing, regrinding and refixing at its original location including replacement of unsv parts, cleaning, repacking stuffing box of sluice valve and spindle including fixing and testing complete all as directed.Note :- (i) Loading/unloading & transportation charges shall be deemed included in the quoted rates.(ii) S&F of spare parts shall be measured and paid separately under respective items:- |
| 34 | Replacement of Hand wheel |
| 35 | Replacement of SS Stem & GM Nut |
| 36 | Replacement of Cap |
| 37 | Replacement of Flange Rubber Gasket |
| 38 | Replacement of Nut & Bolt + 2 Washers |
| 39 | Decoupling, disconnecting sluice valve of size 80 mm dia, taking down from pipe line, opening all parts for refacing, regrinding and refixing at its original location including replacement of unsv parts, cleaning, repacking stuffing box of sluice valve and spindle including fixing and testing complete all as directed.Note :- (i) Loading/unloading & transportation charges shall be deemed included in the quoted rates.(ii) S&F of spare parts shall be measured and paid separately under respective items:- |
| 40 | Replacement of Hand wheel |
| 41 | Replacement of SS Stem & GM Nut |
| 42 | Replacement of Cap |
| 43 | Replacement of Flange Rubber Gasket |
| 44 | Replacement of Nut & Bolt + 2 Washers |
| 45 | M&L for repair to leaking run lead joints in CI/DI spigot and socket end pipelines of 200 mm to 250 mm bore, by providing new lead using good quality jute spun yarn, including necessary excavation in any type of soil, bailing out of water, returning, filling-in and ramming of excavated soil in trenches, and making good all disturbed surfaces such as roads, floors and walls to match the existing finish, at any depth, complete, all as specified and as directed by the Engineer-in-Charge.Notes:(a) The contractor shall be fully responsible for carrying out all necessary excavation for jointing work, arranging required tools and plant, mechanical excavation (if required), manpower at site, and for making good all disturbed surfaces of roads, walls, floors, etc., to match the existing surface. The cost of the same shall be deemed to be included in the quoted rate.(b) Any extra fittings or additional length of pipe, if required, shall be measured and paid for separately.(c) Pig lead and jute spun yarn shall be measured and paid for separately under respective items of Schedule ‘A’. |
| 46 | Description all as per ser item 29.00 here-in-before but size of dia 100 mm to 150 mm bore pipe |
| 47 | M&L for repair to leaking GI pipeline of 80 mm bore, by providing and fixing necessary fittings such as sockets, tees, elbows, etc., including necessary excavation in any type of soil, bailing out of water, returning, filling-in and ramming of excavated soil in trenches, and making good all disturbed surfaces such as roads, floors and walls to match the existing finish, at any depth, complete, all as specified and as directed by the Engineer-in-Charge.Notes:(a) The contractor shall be fully responsible for arranging all necessary excavation for jointing work, required tools and plant, mechanical excavation (if required), manpower at site, and for making good all disturbed surfaces of roads, walls, floors, etc., to match the existing surface. The cost of the same shall be deemed to be included in the quoted rate.(b) Any additional length of GI pipe required shall be measured and paid for separately. |
| 48 | Description all as per ser item 31.00 here-in-before but size of 40 mm to 50 mm bore pipe. |
| 49 | Description all as per ser item 31.00 here-in-before but size of 15 mm to 25 mm bore pipe. |
| 50 | Repair of leaking flanged or circumferential welded joints of 100 mm to 200 mm bore MS/GI pipelines, including the cost of welding materials and labour, providing and fixing rubber or fibre board gaskets, nuts, bolts and washers, and replacement of flanges wherever required at site. The item also includes carrying out welding works wherever necessary, complete. The work shall further include necessary excavation in any type of soil, bailing out of water, returning, filling-in and ramming of excavated soil in trenches, and making good all disturbed surfaces such as roads, floors and walls to match the existing finish, at any depth, complete, all as specified and as directed by the Engineer-in-Charge.Notes:(a) The contractor shall be fully responsible for arranging all necessary excavation, tools and plants, mechanical excavation (if required), manpower at site, arrangement of electric supply, and for making good all disturbed surfaces of roads, walls, floors, etc., to match the existing surface. The cost of the same shall be deemed to be included in the quoted rate.(b) Any additional length of pipe required shall be measured and paid for separately. |
| 51 | Description all as per ser item 34.00 here-in-before but size of dia 250 to 300 mm bore pipe |
| 52 | Material and labour for cutting of existing road / hard standing/ floors/ walls for crossing of MS / DI / CI / GI pipelines for laying of pipes of any size, including necessary excavation and earthwork, and making good and repairing the cut portion with premix bituminous carpet / RCC / PCC/ Pavor block, as per the existing surface, with width of trench not exceeding 0.75 m and depth not exceeding 1.5 m, complete, all as specified and as directed by the Engineer-in-Charge. |
| 53 | M&L PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) cement concrete in as in foundation filling of pole & stay complete, all as specified and as directed by the Engineer-in-Charge. |
| 54 | S&F of Gun-metal, globe or gate valves, 50 mm dia , heavy duty, with iron wheel head, screwed both ends (ISI marked), complete all as specified & directed by Engr-in-Charge. Make: Kirloskar, Zoloto, Leader, L&T, Kartar, BIR |
| 55 | Description all as per ser item 38.00 here-in-before but size of but upto 40 mm bore. |
| 56 | Description all as per ser item 38.00 here-in-before but size of but upto 25 mm bore. |
| 57 | Description all as per ser item 38.00 here-in-before but size of but upto 20 mm bore. |
| 58 | Description all as per ser item 38.00 here-in-before but size of but upto 15 mm bore. |
| 59 | Supply and fixing of pig lead for jointing of CI / DI pipes, including heating and pouring of molten lead into the joint, proper caulking and finishing of joints, complete, all as required at site and as specified and directed by the Engineer-in-Charge. |
| 60 | Supply and fixing of jute spun yarn for jointing of CI / DI pipes, including packing of yarn in the spigot and socket joint to the required depth, proper ramming, finishing of the joint prior to lead pouring, complete, all as required at site and as specified and directed by the Engineer-in-Charge. |
| 61 | Material and labour for decoupling and disconnecting suction and discharge pipelines, dismantling and taking down the pump set from foundation, dismounting from base channels, stripping and opening of all pump components, derusting, cleaning, and complete overhauling, including repair or replacement of unserviceable parts of the pump set, and transportation to workshop for repairs wherever required. Reassembling of the pump set, mounting and fixing on base channels, recoupling of suction and discharge lines, alignment, commissioning and testing, complete, in respect of centrifugal / multistage pump of capacity 30/40/50 HP, all as specified and as directed by the Engineer-in-Charge.Note: The quoted rate shall be deemed to include the following:(i) Provision of hydra crane, if required, complete with operator, helper(s) and requisite number of mates for decoupling, disconnecting, loading, unloading, positioning, fixing on base channels, recoupling of suction and discharge lines and alignment of pump set.(ii) Vehicle for transportation of pump set to and from workshop, wherever required.(iii) Manpower comprising Skilled Pump Mechanic for dismantling, overhauling, reassembly and alignment works.(iv) Tools & Plants including slings, lifting tackles, holding/catching devices, clamps, load supports and all other accessories required for safe handling of the pump set.(v) Skilled Electrician for disconnection and reconnection of electrical connections of pump motor and associated control panel, including testing after reinstallation.(vi) Supply and fixing of replacement parts, shall be measured and paid for separately under the relevant items of Schedule ‘A’. |
| 62 | Description all as per ser item 45.00 here-in-before but capacity 15/20/25 HP. |
| 63 | Supply and fixing of new spare parts for single stage / double stage / multistage centrifugal pump sets of capacity up to 30/40/50 HP, as per manufacturer’s standard composition and specifications of the existing make and model of pump, including replacement of worn-out, damaged or unserviceable components, complete, all as specified and as directed by the Engineer-in-Charge. |
| 64 | Impeller, MOC: CI |
| 65 | Shaft, MOC: CS |
| 66 | Shaft sleeves, MOC: BR |
| 67 | Casing bearing, MOC: CI |
| 68 | Bearing housing/Bearing cover, MOC: CI |
| 69 | Gland cup with nut and bolts, MOC: CI |
| 70 | Jaw/Spider/Star/Tyre Coupler, MOC: CI |
| 71 | Inter stage ring/Shaft sleeve nut, MOC: BR |
| 72 | O Ring, MOC: Neopren rubber |
| 73 | Packings/Mechanical seal |
| 74 | Supply and fixing of new spare parts for single stage / double stage / multistage centrifugal pump sets of capacity up to 15/20/25 HP, as per manufacturer’s standard composition and specifications of the existing make and model of pump, including replacement of worn-out, damaged or unserviceable components, complete, all as specified and as directed by the Engineer-in-Charge. |
| 75 | Impeller, MOC: CI |
| 76 | Shaft, MOC: CS |
| 77 | Shaft sleeves, MOC: BR |
| 78 | Casing bearing, MOC: CI |
| 79 | Bearing housing/Bearing cover, MOC: CI |
| 80 | Gland cup with nut and bolts, MOC: CI |
| 81 | Jaw/Spider/Star/Tyre Coupler, MOC: CI |
| 82 | Inter stage ring/Shaft sleeve nut, MOC: BR |
| 83 | O Ring, MOC: Neopren rubber |
| 84 | Packings/Mechanical seal |
| 85 | Lath/Mchining works of any type at workshop required for balancing of impller/for fixing of new parts to existing shfts required for proper setting and smooth functioning to achieve desired discharge of the pump for 30 HP to 50 HP pump complete all as specified and as directed by Engr-in-charge. |
| 86 | Description all as per srl item No. 49.00 here-in-before but capacity of 15 HP to 25 HP motor |
| 87 | Material and labour for disconnecting electrical connections of 30/40/50 HP motor, dismantling and removing the unserviceable motor from its existing position by unscrewing foundation bolts and nuts, decoupling the motor from the pump, shifting and transporting the same to workshop for repairs, including dismantling of motor, cutting and removal of burnt stator/rotor windings, cleaning of slots, and transporting the motor back after repairs/winding. Re-assembling, refixing and aligning the motor at its original location, including coupling with pump, commissioning and testing, complete, all as specified and as directed by the Engineer-in-Charge.Note:(i) Rewinding of motor stator and/or rotor shall be measured and paid for separately under the relevant items of Schedule ‘A’.(ii) The quoted rate shall be deemed to include the cost of loading, unloading, transportation, Bearings, grease, nuts, bolts and washers of any size and shape, minor consumables, refixing of serviceable motor, electrical reconnection, alignment with pump, and making the motor fully functional, including testing at its existing location/position, complete, all as specified and as directed by the Engineer-in-Charge. |
| 88 | Description all as per srl item No. 51.00 but capacity of 10/15/20/25 HP motor |
| 89 | Removing burnt-out winding from rotor and stator, cleaning of slots thoroughly, repairing and refilling of damaged slots wherever required with approved insulating/slot repair material, providing and inserting high quality Class ‘B’ insulation paper inside the slots, rewinding of electric motor of capacity 75/60/50/40/30/25/20/15/12/10/5/3/2/1.5 HP with super enamelled copper winding wire of same size and gauge as per existing, wrapping with high quality cotton tape, varnishing with superior quality insulating varnish, including baking/drying at required temperature and for required duration, complete, all as specified and as directed by the Engineer-in-Charge.Note: The quoted rate shall be deemed to include the cost of all labour, slot repairing/refilling material, insulation, winding, varnishing, baking/drying and routine testing. |
| 90 | S&F Bearing No. 6305 C3, including dismantling of old/unserviceable, cleaning, re-alignment, lubrication, and testing, complete, all as specified and directed by the Engineer-in-Charge. |
| 91 | S&F Bearing No. 6307 C3, including dismantling of old/unserviceable, cleaning, re-alignment, lubrication, and testing, complete, all as specified and directed by the Engineer-in-Charge. |
| 92 | S&F Bearing No. 6308 2RS1/C3, including dismantling of old/unserviceable, cleaning, re-alignment, lubrication, and testing, complete, all as specified and directed by the Engineer-in-Charge. |
| 93 | S&F Bearing No. 3307 ATN9, including dismantling of old/unserviceable, cleaning, re-alignment, lubrication, and testing, complete, all as specified and directed by the Engineer-in-Charge. |
| 94 | S&F Bearing No. 6306 2Z/C3, including dismantling of old/unserviceable, cleaning, re-alignment, lubrication, and testing, complete, all as specified and directed by the Engineer-in-Charge. |
| 95 | S&F Bearing No. 7310 BEP, including dismantling of old/unserviceable, cleaning, re-alignment, lubrication, and testing, complete, all as specified and directed by the Engineer-in-Charge. |
| 96 | Supply, installation, testing and commissioning of OFF-load changeover switch, 630 Amps, 415 Volts, 4-pole, side-handle operated, complete with stainless steel enclosure of approved gauge including Including taking down and dismantling of existing old/unserviceable OFF-load changeover switch, disconnecting of incoming and outgoing power cables, supply and fixing of new changeover switch in replacement, refixing and reconnecting of incoming and outgoing cables with new suitable size cable lugs, nuts, bolts, washers and insulating sleeves, proper termination, alignment and tightening, earthing connections, and making good disturbed surfaces,complete, all as specified and directed by the Engineer-in-Charge. |
| 97 | Description all as per srl item No. 60.00 here-in-before but of capacity 400 Amps. |
| 98 | Description all as per srl item No. 60.00 here-in-before but of capacity 320 Amps. |
| 99 | Description all as per srl item No. 60.00 here-in-before but of capacity 200 Amps. |
| 100 | Supply, installation, testing and commissioning of on-load changeover switch, 320 Amps, 415 Volts, 4-pole, suitable for LT applications, complete with all necessary accessories. Including dismantling, disconnecting and removal of existing old/unserviceable on-load changeover switch, supply and fixing of new changeover switch in replacement in the existing LT panel, disconnecting and reconnecting incoming and outgoing power cables with proper termination using suitable size cable lugs, nuts, bolts, washers and insulating sleeves, providing earthing connections, alignment and tightening of terminals, and making good disturbed surfaces. |
| 101 | Description all as per srl item No. 64.00 here-in-before but of capacity 200 Amps and side handle operated. |
| 102 | S&F in relpacement of load line MCCB 320 Amps 4 pole 415 volts with adjustable thermal and fixed magnetic setting of breaking capacity 35/36KA, Ics=100% Icu including taking down the old existing MCCB complete all as directed by Engr in charge. |
| 103 | Description all as per srl item No. 66 here-in-before but of capacity 250 Amps. |
| 104 | Description all as per srl item No. 66 here-in-before but of capacity 200 Amps. |
| 105 | Description all as per srl item No. 66 here-in-before but of capacity 160 Amps. |
| 106 | Description all as per srl item No. 66 here-in-before but of capacity 125 Amps. |
| 107 | Description all as per srl item No. 66 here-in-before but of capacity 63 to 100 Amps. |
| 108 | Supply, installation, testing and commissioning of power contactor, 3-pole, AC-3 duty, suitable for 415 V, 50 Hz, with AC coil, current rating suitable for motor capacity up to 40/50 HP and FRAME size shall match the existing contactor, complete with auxiliary contacts (minimum 1 NO + 1 NC), arc chutes, terminal shrouds, mounting accessories, internal control wiring with ferrules, and electrical/mechanical interlocking arrangement (where applicable), including dismantling of old/unserviceable contactor and refixing of new contactor in existing star-delta starter / LT panel, complete, all as specified and directed by the Engineer-in-Charge. Make: Same as existing Siemens / L&T / Schneider / ABB / Havells, or equivalent of matching frame size and mounting to suit existing starter/panel, conforming to relevant IS / IEC standards. |
| 109 | Description all as per srl item No. 72.00 here-in-before but suitable for motor capacity up to 25/30 HP. |
| 110 | Description all as per srl item No. 72.00 here-in-before but suitable for motor capacity up to 10/15/20 HP. |
| 111 | Supply, installation, testing, and commissioning of thermal overload relay (OLR) suitable for three-phase induction motors up to 50 HP, with adjustable current range matching the motor’s full-load current, including single-phasing protection, manual/auto reset facility, and trip indication. The OLR shall be fully compatible with AC-3 duty contactors. The work includes dismantling of old/unserviceable OLR and refixing of the new OLR on the existing contactor in star-delta starter / LT panel, complete with all required wiring, ferrules, setting of current, and functional testing under load. Make: Same as existing Siemens / L&T / Schneider / ABB / Havells, or equivalent, ensuring compatibility with existing starter/contactor, and conforming to relevant IS / IEC standards, as specified and directed by the Engineer-in-Charge. |
| 112 | Supply, installation, testing and commissioning of electronic star-delta timer, panel-mounting type, suitable for 415 V AC, 50 Hz system, with adjustable time delay range 0–30 seconds / 0–60 seconds, having minimum 2 NO + 2 NC potential-free contacts, LED status indication, suitable for use in star-delta starter for motors up to 50 HP, including dismantling of old timer (if any), mounting, wiring, integration with existing control circuit, setting of time delay, testing and commissioning, complete, all as specified and directed by the Engineer-in-Charge. Make: Same as existing Siemens / L&T / Schneider / ABB / Havells, or equivalent of matching mounting and compatibility to suit existing contactor/starter, conforming to relevant IS / IEC standards. |
| 113 | Supply, laying, and fixing in replacement of PVC insulated, heavy-duty, single-core flexible copper conductor industrial cable, 1100 V grade, nominal cross-sectional area 70 sq. mm, including taking down of existing unserviceable cable, complete in all respects as per directions of the Engineer-in-Charge.Note: Excavation, earthwork, sand cushioning, protection with DWC/GI pipes, cable lugs, etc., shall be measured and paid separately under the respective items of Sch ‘A’. |
| 114 | Description all as per srl item No. 77.00 here-in-before but of size 50 sqmm. |
| 115 | Description all as per srl item no. 77.00 here-in-before but of size 35 sqmm. |
| 116 | Description all as per srl item no. 77.00 here-in-before but of size 25 sqmm. |
| 117 | Supply and fixing of heavy-duty copper thimble (lug), tinned, compression type, suitable for 70 sq. mm single-core copper conductor cable, including taking down and removal of existing unserviceable copper thimble, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 118 | Description all as per srl item no. 81.00 here-in-before but of size 50 sqmm. |
| 119 | Description all as per srl item no. 81.00 here-in-before but of size 35 sqmm. |
| 120 | Description all as per srl item no. 81.00 here-in-before but of size 25 sqmm. |
| 121 | M&L for aluminium thimble of 120 sqmm size for cables complete, all as specified and directed by Engr-in-Charge |
| 122 | Description all as per srl item No. 85.00 here-in-before but of size 95 sqmm. |
| 123 | Description all as per srl item No. 85.00 here-in-before but of size 50 sqmm. |
| 124 | S&F in replacement analog type Ampere meter (96mm x96 mm) complete with suitable CTs 0-300 Amps as per existing,complete all as specified and directed by Engineer - in - Charge. |
| 125 | S&F in replacement of analog type volt meter (96mm x96 mm) 0-500 volts as per existing, complete all as specified and directed by Engineer - in - Charge. |
| 126 | S&F in replacement of indicating lamps RYB as per existing, complete all as specified and directed by Engineer - in - Charge. |
| 127 | S&F in replacement of Push button as per existing, complete all as specified and directed by Engineer - in - Charge. |
| 128 | S&F in replacement of Twin Touch with Black centre strip type Push button as per existing, complete all as specified and directed by Engineer - in - Charge. |
| 129 | S&F in replacement of selector switch as per existing, complete all as specified and directed by Engineer - in - Charge. |
| 130 | Phase Changeover switches |
| 131 | Ammeter Selector Switches |
| 132 | Voltmeter Selector Switches |
| 133 | Changeover Selector Actuators (Side/Lever Handle) |
| 134 | Changeover Selector Actuators (Operating Handle) |
| 135 | Supply and laying DWC (Double wall corruguated) pipe 40/32 mm conforming to IS-14930/ IS-16205 for protection of earth strip/cable including necessary snap fit coupler reqd for fixing complete all as specified and directed by Engr-in-charge |
| 136 | Description all as per srl item no. 94.00 here-in-before but of size 63/50 mm. |
| 137 | Supply and fixing in replacement of motor terminal box complete assembly, consisting of terminal enclosure box (outer housing) and internal terminal block, of approved make and workmanship, suitable for induction motors of rating 30/40/50 HP, matching the existing make, dimensions, mounting arrangement, and specifications, including taking down and removal of the existing complete terminal box assembly (enclosure box along with internal terminal block), supply and fixing of new complete terminal box assembly including terminal studs, insulation base, gasket, cover, fixing hardware, and making all electrical connections properly includes checking, tightening, insulation verification, and ensuring the motor is ready for safe and satisfactory operation, complete all as specified and as directed by the Engineer-in-Charge. |
| 138 | Description all as per ser item No 96.00 here-in-before but for motor of ratting 15/20/25 HP. |
| 139 | Material and labour for painting of pump set (including motor and frame) 15 HP to 50 HP, including surface preparation by scraping and cleaning with emery paper to remove rust, scale, and loose paint, and applying one coat of red oxide primer followed by two coats of synthetic enamel paint of approved make and existing colour, complete, to the satisfaction of the Engineer-in-Charge. |
| 140 | S&F in replacement of Gland Packing Rope type 3 of size 8 mm made of asbestos grip with silicon complete all as specified and directed by Engr-in-Charge. |
| 141 | Description all as per srl item No. 99 here-in-before but of size 10 mm. |
| 142 | Supply and laying of synthetic rubber insulated electrical safety mats, minimum 2.5 mm thick, suitable for use up to 11 kV, conforming to IS 15652, for electrical shock protection, anti-skid type, of size 2.0 m × 1.0 m, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 143 | Supply only, in replacement, of mild steel (MS) stud bolts of existing size, suitable for pumps and motors of various capacities installed at site, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 144 | Supply only, in replacement, of grouting nuts and bolts of existing size, suitable for pumps and motors of various capacities including their foundations, and for sluice valves, non-return valves, foot valves, and air-release valve flanges installed at site, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 145 | Supply, fabrication and fixing of mild steel (MS) pipe fittings/joints such as flanged joints, bends, tees, tapers, collars, elbows, tail pieces (any type), caps and plugs for pipes of 80 mm to 300 mm bore, including taking down existing/old fittings, complete in all respects, including cutting, aligning and fixing, all as specified and as directed by the Engineer-in-Charge.Note: The quoted rates shall be deemed to include material and labour (M&L) charges for all required welding and associated works. |
| 146 | Supply only lithium base grease AP3 in 20 Kg pack suitable for application to ball bearing with operating temperature 30 to 120 degree celsius drop point 174 degree celsius, colour light fawn complete all as specified and directed by Enr-in-Charge |
| 147 | Supply only cotton waste coloured Grade \\"A' for cleaning rags in 25 Kgs bag complete all as specified and directed by Engr-in-Charge |
| 148 | M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to galvanised iron strip 32×6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised standard iron or steel all as specified or indicated in electrical plate no 3 of MES Part-I, including testing on completion including the material and labour of the following :-(a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1.(c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm.(d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified. (e) 15 mm nominal bore light grade GI protection pipe 7.5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal.(g) Testing of earthing.Note : On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge. |
| 149 | Supply and fixing black flexible rubber Tyre coupling as per sample TC 14,TC 15, TC 16, TC 17, etc complete all as specified and directed by Engineer-in-Charge. |
| 150 | Supply and fixing flexible rubber star coupling as per sample complete all as specified and directed by Engineer-in-Charge. |
| 151 | Supply, installation, testing and commissioning of glycerin-filled analog pressure gauge in replacement, suitable for water pump delivery line, bourdon tube type, with 100 mm dial size, accuracy class 1.0, stainless steel internal parts, bottom connection ½” BSP, dual scale pressure range 0–10 bar / 0–150 psi / 0–10 kg/cm², suitable for pumps having operating head up to 80 m and maximum discharge up to 5000 LPM, complete with siphon, isolation valve, necessary mounting arrangement and all accessories, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 152 | Taking out / taking down (retrieval) of unserviceable XLPE armoured LT underground/ laid along wall / laid on floor cable of any size and capacity, complete in all respects, including disconnection, careful removal, handling, stacking at designated location, and making good disturbed surfaces, all as specified and as directed by the Engineer-in-Charge. |
| 153 | Supply, laying, fixing, jointing, testing, and commissioning of LT power cable, XLPE insulated, galvanized steel strip armoured, 3.5 core × 120 sqmm, 1100 Volt grade, heavy-duty, ISI marked, with aluminium conductor, overall sheathed with PVC, suitable for LT power distribution. The cable shall be laid in trenches, through protective pipes, under floors, or through walls, including necessary bends, supports, saddles/clamps, dressing, termination preparation, identification, and making electrical connections, complete all as specified and as directed by the Engineer-in-Charge. The item also includes taking down, dismantling, and removal of the existing unserviceable LT cable of similar capacity from site, complete.Notes:(i) Excavation, refilling, earthwork, sand cushioning, brick/cover protection, protective pipes/ducts, and related civil works shall be measured and paid for separately under the relevant items of Schedule ‘A’.(ii) Cable terminations, glands, lugs, and end connections shall be deemed to be included in quoted item rate. |
| 154 | Description all as per srl item No. 112.00 here-in-before but of size 95 sqmm 3.5 core. |
| 155 | Description all as per srl item No. 112.00 here-in-before but of size 50 sqmm 3.5 core. |
| 156 | Supplying and fixing RCC water pipeline route marker of milestone type, made out of reinforced cement concrete of approved quality, of standard market-available size upto 1000 mm height × 300 mm width × 100 mm thickness, with rounded top, painted with approved colour code for water pipeline, and provided with stencil-painted inscription indicating “WATER PIPELINE”, diameter of pipeline and other details as approved by the Engineer-in-Charge, including excavation, PCC bedding if required, embedding the marker minimum 300 mm below ground level, fixing vertically and firmly in position, finishing, painting, lettering and erection of old, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 157 | Providing and carrying out welding of any type (electric arc / gas welding) for fabrication, erection or repair of steel/MS/GI members, brackets, frames, supports, angles, flats, pipes etc. of any size and thickness, including surface preparation, alignment, welding consumables, finishing and all incidental works, complete, measured per stick/ filler rod / welding rod, all as specified and directed by the Engineer-in-Charge |
| 158 | M&L for PCC pillars, including dismantling of existing pillars, of size 0.9 m × 0.6 m × 1.8 m (comprising 0.6 m below ground level and 1.2 m above ground level) for mounting and leveling of the header at a height of 1.5 m above ground level, complete as specified and as directed by the Engineer-in-Charge.Note: The quoted rate shall be deemed to include the following:(a) Excavation in trenches not exceeding 1.5 m width and 1.5 m depth, including removal of hard/dense soil, complete as specified and directed.(b) Returning and filling of excavated material, including spreading, levelling, watering, and well ramming in layers not exceeding 25 cm, complete as specified.(c) Transportation of excavated material up to 50 m and depositing at locations directed by the Engineer, at a level not exceeding 1.5 m above the starting point, complete as directed.(d) M&L of PCC 1:3:6 (C-2) using 40 mm graded crushed stone aggregate for foundation filling of pillars, complete as specified and directed.(e) M&L of RCC foundations, M-25 (using 20 mm graded aggregates), including rafts, footings, foundation beams, plinth beams, column bases, basement slabs, under-reamed piles, and mass concrete, complete as specified and directed by the Engineer-in-Charge.(f) M&L of RCC columns, M-25 (using 20 mm graded aggregates), complete as specified and directed.(g) Supply, cutting, bending, cranking, and placement of mild steel bars of 10 mm dia and above, including spiral hooping for columns, hooking of ends, binding with annealed mild steel wire not less than 0.9 mm dia, or securing with clips, complete as specified and directed.(h) Cost of labour for mounting the header on PCC pillars. (i) Prior to mounting, the strength of each pillar shall be tested. If a pillar fails to meet the required strength, it shall be dismantled and reconstructed by the contractor at his own risk and cost, to the complete satisfaction of the Engineer-in-Charge. |
| 159 | M&L for cutting of existing GI/CI water main pipeline up to 150 mm bore in position for making branch connection/ insertion of GI tee, including excavation and earthwork, complete all as specified and directed by Engr-in-Charge.Note: GI fittings such as tee, elbows, collars, reducers, etc., and jointing material for fixing of cast iron fittings shall be measured and paid for separately. |
| 160 | Description all as per ser item No 118.00 here-in-before but of dia 100 mm complete all as specified and directed by Engr-in-Charge. |
| 161 | Description all as per ser item No 118.00 here-in-before but of dia 80 mm complete all as specified and directed by Engr-in-Charge. |
| 162 | Providing, fabricating and fixing Mild Steel (MS) sheet cover for inspection/outlet opening of Rapid Sand Filter Bed/ Lid on Storage tank/ Cover on Valve Pit Chamber. The item shall include cutting, welding, grinding and fixing in position, ensuring proper seating and easy opening for operation and maintenance, complete with surface preparation and painting with one coat of red oxide zinc chrome primer and two coats of approved synthetic enamel paint. The cover and brackets shall be gas-cut/fabricated to the exact size of the opening, all as specified and as directed by the Engineer-in-Charge. |
| 163 | Cover sheet door of MS sheet 1.60 mm thick of size 880 mm × 880 mm. |
| 164 | Framed bracket fabricated in MS angle iron 50 mm × 50 mm × 6 mm thick, with all welding included (rate included), and framed bracket in MS strip iron 40 mm × 6 mm thick, complete with stiffeners, hinges and lifting handle, finished and fixed in position, complete all as specified. |
| 165 | Galvanised steel wire netting of 0.91 mm dia with mesh size 12 mm on tank air ventilator openings for prevention of ingress of birds and insects, complete all as specified. |
| 166 | Supply and fixing GI fittings medium grade ISI marked including complete all as required at site and as directed by Engr-in-Charge. |
| 167 | Elbow 15mm |
| 168 | Elbow 20mm |
| 169 | Elbow 25mm |
| 170 | Elbow 40mm |
| 171 | Elbow 50mm |
| 172 | Elbow 80mm |
| 173 | Socket 15mm |
| 174 | Socket 20mm |
| 175 | Socket 25mm |
| 176 | Socket 40mm |
| 177 | Socket 50mm |
| 178 | Socket 80mm |
| 179 | Union 15mm |
| 180 | Union 20mm |
| 181 | Union 25mm |
| 182 | Union 40mm |
| 183 | Union 50mm |
| 184 | Union 80mm |
| 185 | Elbow reducer 25 x 20mm |
| 186 | Elbow reducer 20 x 15mm |
| 187 | Elbow reducer 40 x 25mm |
| 188 | Socket reducer 25x20mm |
| 189 | Nipple 15mm |
| 190 | Nipple 20mm |
| 191 | Nipple 25mm |
| 192 | Nipple 40mm |
| 193 | Nipple 50mm |
| 194 | Nipple 80mm |
| 195 | Tee 15mm |
| 196 | Tee 20mm |
| 197 | Tee 25mm |
| 198 | Tee 25x20mm |
| 199 | Dead plug 15mm |
| 200 | Dead plug 20mm |
| 201 | Dead plug 25mm |
| 202 | Dead plug 40mm |
| 203 | Dead plug 50mm |
| 204 | Dead plug 80mm |
| 205 | Refixing GI pipe obtained from Item No. 04 above and connections in new or old position (walls, trenches, ceiling and floors etc) of size 100 mm dia complete including main branch connections all as specified and directed by Engr-in-Charge. |
| 206 | Description all as per ser item No 123.00 here-in-before but of 80 mm dia obtained from item No. 05. |
| 207 | Description all as per ser item No 123.00 here-in-before but of 50 mm dia obtained from item No. 06. |
| 208 | Description all as per ser item No 123.00 here-in-before but of 40 mm dia obtained from item No. 07. |
| 209 | Description all as per ser item No 123.00 here-in-before but of 25 mm dia obtained from item No. 08. |
| 210 | Description all as per ser item No 123.00 here-in-before but of 20 mm dia obtained from item No. 09. |
| 211 | Description all as per ser item No 123.00 here-in-before but of 15 mm dia obtained from item No. 10. Total in Figures 0.0 0.0 INR Zero Only 4.0 Construction of chamber for 100mm sluice plates item5 10.0 Nos Quoted Rate in Figures Select 0.0 0.0 Zero Only Quoted Rate in Words INR Zero Only Please Enable Macros to View BoQ information |
