|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 4 | 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 5 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : |
| 7 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for : |
| 9 | Small works not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks , concrete for angle grouting and the like works. |
| 10 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 11 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 12 | Brick work with common burnt clay modular bricks of class designation 3.5 in foundation and plinth in: |
| 13 | Cement Mortar 1:6 (1 cement : 6 coarse sand). |
| 14 | Providing and laying half block masonry with factory made Precast concrete solid blocks of 100 mm thickness of grade M10 made of C&D waste from approved manufacturer in foundation and plinth (for construction of side walls Drains ,chambers etc ) in : |
| 15 | Cement mortar 1:6 (1 cement : 4 coarse sand) |
| 16 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 17 | In gratings, frames, guard bar, ladder, railings, brackets, gates, covers and frames of chamber etc. and similar works . ( including steel sheets of any thickness to be used in CNC work) |
| 18 | Smooth finishing of the exposed surface of R.C.C. & C.C. work with 6 mm thick cement mortar 1:3 (1 Cement : 3 fine sand). |
| 19 | 12 mm average thickness cement plaster of mix : ( on Brick work and Half block work , inside chambers and drains etc .) |
| 20 | 1:6 (1 cement: 6 fine sand) |
| 21 | Finishing walls with Acrylic Smooth exterior paint of required shade : on New plaster work |
| 22 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 23 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 24 | Two or more coats on new work. |
| 25 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 26 | One or more coats on old work. |
| 27 | Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required, |
| 28 | Circular manhole 140 cm dia with circular cover 600 mm dia |
| 29 | Dismantling barbed wire fencing or flexible wire rope cutting angles , steel posts including making rolls and stacking material within 50 metres lead. |
| 30 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. |
| 31 | With G.I. barbed wire ( over exsisting compound with 5 horizental lines ) |
| 32 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 33 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Note : Different colour paver may be used in pattern as per direction of E-in-C). |
| 34 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 35 | Finishing walls with Acrylic Smooth exterior paint of required shade : on old existing compound wall ,including removing algae, fungus, vegetation, efflorescence , dirt ,etc. by scraping with brushing & sand papering , cleaning and necessary repairs of scratches by wall putty , preparing the surface smooth making it ready for painting work. (a)Two or more coat applied @ 1.67 ltr/ 10 sqm (finishing work will be done in sequence of preparation of surface, then first coat then second coat ) |
| 36 | Providing and laying brick tiles over columns top,edges of roofs and slabs etc for providing architectural offsets or required projections jointing with cement mortar 1:3 (1 cement : 3 fine sand) laid over 12 mm mortar layer of cement mortar 1:3 (1 cement : 3 fine sand) .joints , top, bottom and face shall be finished neat in line level . |
| 37 | With common burnt clay brick tiles |
| 38 | Providing and fixing chhajja, to be fabricated at site, over window at external face of building made of steel members frame and precoated galvanised iron profile sheets of thickness 0.5mm for coverings whole chhajja top and both sides , of required colour size and design fixed to steel frame work made of 50 mm x 5 mm thick MS flats 4 nos.of 3.60 meter straight in logitudinal and 4 nos.of 1.10 meter half rounded in cross direction all welded and supported by angles 50 x 50 x 5 mm size - 2 nos . of 0.80 meter vertical angles fixed on wall face and 2 nos. 0.60 meter horizental angles ( perpendicular to wall face for supporting free end of chajja ) including necessary intermideate holdings to wall by 0.15 meter long 50 x 5 mm 4 nos. ms flate welded to top steel member fixed to wall by bolts / killa for additional support with all required febrication. The chhajja work should be provided and fixed up to a height 12 meter above from ground level , the rate is for each job for one chhajja of 3.60 meter long including cost of scaffolding etc. nothing shall be paid in extra . |
| 39 | Labor charges for cutting CNC (Computer numeric control) on steel sheet of any approved specific design and pattern as per direction of Engineer in charge.(for any thickness of steel sheet , cost of steel sheet and fixing in position will be paid by weight in steel work Item in Kilogram unit) |
| 40 | Cleaning of road side drains (open or covered ) removal of inside garbage , silt, earh deposits , blockages etc. removal of all kind of obstacles from drain including all necessary operations of scraping bootom and sides of drain , roding , flushing with water ,removal and relaying the covers/ sand stone slabs , disposal of malba etc all complete as per site requierment as directed by engineer in charge .) |
| 41 | For small drains below and up to 0.80 meter wide and 1.50 mete depth in sections. |
| 42 | For larger drains (Nala)above and up to 1.80 meter wide and 1.50 mete depth in sections. |
| 43 | Credit for dismantled barbed wire fencing or flexible wire rope cutting angles , steel posts etc. including all lead and lift . Please Enable Macros to View BoQ information |
