|
| 1 | Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil. (As per DSR 2.1.1) |
| 2 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil (As per DSR 2.28.1) |
| 3 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos Lindane emulsifiable concentrate of 20% (As per DSR 2.34.1) |
| 4 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same. (As per DSR 2.35.5) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) (As per DSR 4.1.10) |
| 6 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. (As per DSR 4.17) |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) (As per DSR 6.4.1) |
| 8 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 8.2.2 Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm (As per DSR 8.2.2.2) |
| 9 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (As per DSR 8.31) |
| 10 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Kiln seasoned and chemically treated hollock wood (As per DSR 9.1.3) |
| 11 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(As per DSR 10.2) |
| 12 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 11.41A.1 Double charge vitrified tile polished finish of size Size of Tile 600x600 mm(As per DSR 11.41A.1.1) |
| 13 | Painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : With residual type petroleum bitumen of grade VG -10 (As per DSR 12.15.1) |
| 14 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase (As per DSR 12.21.1) |
| 15 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (As per DSR 12.22) |
| 16 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (As per DSR 12.50) |
| 17 | 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) (As per DSR 13.2.1) |
| 18 | Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing (As per DSR 13.31.1) |
| 19 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) (As per DSR 13.46.1) |
| 20 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture (As per DSR 13.62.1) |
| 21 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (As per DSR 13.80) |
| 22 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour Old work (one or more coats) (As per DSR 13.81.1) |
| 23 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (As per DSR 13.91) |
| 24 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. (As per DSR 13.99.1) |
| 25 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm). (As per DSR 13.111.2) |
| 26 | Renewing glass panes, with wooden fillets wherever necessary: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) (As per DSR 14.6.1) |
| 27 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (As per DSR 15.56) |
| 28 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (As per DSR 15.60) |
| 29 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) (As per DSR 21.1.1.2) |
| 30 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. (As per DSR 21.2.2) |
| 31 | Providing and applying cement based putty (Birla, Jk or equivalent) to the required finish complete in all respect and to the entire satisfaction of Engineer-in-charge. (N.S) |
| 32 | Providing and finishing walls of existing brickwork/ pointing face/ plastered surface finished with acrylic smooth exterior paint at various dispensaries in Chandigarh having pre-defined shade/ colour (of make Asian paint, Berger paint equivalent.) as per latest guidlines of Govt. of India for renaming Ayushman Bharat-Health and Wellness Centres as \\"AYUSHMAN AROGYA MANDIR\\" with tagline 'Arogyam Pramam Dhanam'. The painting colour schemes includes patterns, illustrations, National Health mission logo, Ayushman Bharat logo. The size, dimensions and design of logo is as per drawing supplied by client department. The rates further includes the cost of priming/preparing base smooth for painting complete in all respect and to the entire satisfaction of E.I.C in time bound manner. (N.S) |
| 33 | Providing and fixing wooden cabinet of 13½” deep and 2’-0\\" height with openable shutter consisting of 19mm thick with commercial board (ISI marked) lipped with teak wood lipping of 19mm x 6mm on exposed edges include cost of nail, screws, piano hinges, magnetic catchers, synthetic adhesive etc. The front shutter and sides are to be furnished with 1mm thick ISI marked superior quality mica of approved shade and inner side of the cabinet with 0.8mm thick mica of approved shade fixed in position with help of wooden gutties at wall complete in all respect to the entire satisfaction of Engineer in charge. (N.S) |
| 34 | Providing and fixing 2’ deep cabinet underworking shelve made out with 19mm thick commercial ISI marked board and front portion of the cabinet furnished with 1mm thick superior quality white sunmica on outer side and 0.8mm thick sunmica inner side of the cabinet and synthetic enamel paint over the remaining portion. It also includes the cost of 03 nos. SS handle 5\\", 04 nos. magnetic catcher double strip horizontal style adhesive , SS bright finished piano hinges, nail, screws etc. complete in all respect to the entire satisfaction of Engineer-in-charge. (N.S) |
| 35 | Retile terracing of mud phaska covered with tiles or brick, in cement mortar by reusing dismantled tile or bricks after cleaning and making tile servicalbe for reuse, dismantling mud phaska and cleaning the mother slab propoerly (75mm old earth and 25mm new earth) after performing water proofing treatment which will be paid seperately. Laying 10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat brick tile, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat including replacing unserviceable tiles or bricks with new ones (the cost of the new tiles/bricks excluded) all complete as per direction of Engineer-in-Charge. (N.S) |
| 36 | Providing and Fixing Water proofing treatment with (MAK polyplast regular grade 2104 or equivalent) 1mm thk weighing 1.75 kg/sqm over the surface with two coat of bitumen 85/25 @1.20 kg/sqm fixing polyplast over laps sealed with flame of blown bitumen including cost of sealing the overlap 10cm width complete in all respect to the entire satisfaction of Engineer-In-Charge. (N.S) |
| 37 | Providing and fixing 60 mm thick high density rubber moulded precast cement concrete paver block grey/ colored/ polished/ designer (manufactured by vibro hydraulic pressure process) consisting of design mix of cement, sand and fine aggregate having designation M35 ISI marked including the cost of good quality color and hardening agents. The paver should be compiled with tensile strength and breaking load as per BIS 6717-1993 and shall be tested against resistance to bear as per IS 1237-1980 (specification for cement concrete floor tiles). The paver should be laid over layer of 50mm average thick sand to the required slope and requirement complete in all respects and to the entire satisfaction of Engineer in charge. (N.S) |
| 38 | Providing and fixing of factory manufactured pre-cast concrete kerb of size 300mm X 300mm having 150 mm thickness with one edge semi rounded duly vibrated mechanically and compacted made of P.C.C. 1:2:4 duly cured and finished. the rate further include filling of joints between kerbs/ channels with cement mortar 1:2 complete in all respect and to the entire satisfaction of Engineer-in-charge. (N.S) |
| 39 | Providing and fixing 35mm thick golden champ wood (kiln seasoned) glazed window shutters consisting of vertical and horizontal styles 75x35mm size with 4mm thick floated glass pane fixed with 1/2\\"x3/4\\" golden champ wood (kiln seasoned) beading. The rate further includes the cost of 2 nos. 3\\" hinges, 2 nos. Aluminium tower bolts 4\\", Aluminium handles 1 nos., I-hook and two coats of special quality enamel paint over coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge. (N.S) |
| 40 | Repair of deteriorated RCC Balconies, Chajjas, Beams, Walls, Ceiling, Column or other concrete surface having exposed rusted bars consisting of following operations (a) chipping of concrete surface 25mm thick average depth afterwards remocal of loose concrete and exposing the steel bars. Cleaning the surface properly to remove dust particles and rust from the steel bars. (b) Moistening the surface properly and applying arcylic polymer (acrocrete/ pidilite/ mastercrete or its equivalent) coating mixed with cement for proper bonding of old and new concrete in two coats 0.2kg per 1kg of cement. (c) Providing and fixing chicken mesh of standard size and 26 guage with steel reinforcement by using binding wire and nails complete. (d) Proving and placing of cement concrete l:11/2:3 having average thickness 1\\" (3/4\\" to 11/4\\" thick) mixed with arcylic polymer admixture @ 1kg per bag of cement and waterproof agent @ 400ml per 2 bags of cement including finishing the surface complete in all respect as per the direction and to the entire satisfaction of Engineer-in-Charge. (N.S) |
| 41 | Providing and fixing IRC welded mesh size 25mmx25mm in the existing M.S frame including coast of cutting welding and one coat of metal primer complete in all respects and to the entire satisfaction of the engineer in charge (N.S) |
| 42 | Supply of 1st quality brick tiles 9\\" X 4 1/2\\" X 1 1/2\\" complete in all respects to the entire satisfaction of Engineer in charge. (N.S) Please Enable Macros to View BoQ information |
