|
| 1 | Earth work in excavation in all kinds of soil for structure as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto any lead and dressing of sides and bottom and back filling in trenches with excavated suitable material including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 2 | Providing and laying cement concrete 1:4:8 (One cement : four sand : eight graded crushed stone aggregate 40mm (forty millimetre nominal size) concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 including the cost of form work and carriage of material in all leads, lifts as per the entire satisfaction and direction of Engineer-in-Charge. |
| 3 | Providing and laying 1:5:10 (One cement : five sand : ten graded stone aggregate 40mm (Forty millimetre nominal size) concrete for plain/reinforced concrete in open foundations and curing complete including form work as per drawing and technical specification clauses 802, 803, 1202 and 1203 including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in-charge. |
| 4 | Providing weep holes in block masonry/ stone masonry/ plain reinforced concrete abutments wing wall, return wall with 100mm PVC pipe extending through the full width of the structure with slope of I (V) : 20 (H) towards drawing face complete as per drawing and technical specifications clause 614, 709, 1204.3.7 including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 5 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material upto any lead as per direction of Engineer - in- charge. |
| 6 | Providing form work with steel plates 3.15mm (three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (thirty millimetre into thirty millimetre into five millimetre) in suspended floor roof etc so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals. |
| 7 | Providing and laying mechanically mix and vibrated in position cement concrete 1:1.5:3 (one cement : one point five sand) : three graded stone aggregate 20 mm (twenty millimetre) nominal size) of specified grade excluding the cost of centering and shuttering up to plinth level including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer - in- charge . |
| 8 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding complete upto floor two level including the cost of binding wire and above on floor all level. Thermo-Mechanically Treated bars of grade Fe-500D including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 9 | Second class brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:4 (one cement : four sand) including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer - in- charge . |
| 10 | Providing and laying antiskid vetrified matte finish tiles size 600x600 mmx10mm (six hundred into six hundred into ten millimetre) coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:4 (one cement: four sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match including rubbing and polishing complete including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 11 | Providing and laying spartic ceremic tiles 300x300mm (three hundred into three hundred millimetre) size 5.5mm (five point five millimetre) thick in flooring, tread of steps laid on bed of 12mm (twelve millimetre) thick cement mortar 1:4 (one cement : four sand) and jointed with cement slurry including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 12 | Providing and laying spartic ceremic tiles 300x300mm (three hundred into three hundred millimetre) size 5.5mm (five point five millimetre) thick in walls and treads, treads of steps laid on bed 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 13 | Providing and fixing 35mm to 40 mm (thirty five to forty millimetre) thick second class deodar wood shutters, panelled glazed or panelled and glazed shutters for doors, windows and clerestory windows and including black enamelled iron butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals. |
| 14 | Providing and fixing wire gauge shutter in Z- section using galvanised MS wire gauge of IS gauge designations 85G with wire of dia 0.56mm (zero point five six millimetre) for doors, windows and clearstory windows including metal beading of approved quality and shape section with necessary steel screws including applying a priming coat of red lead paint complete as per approved specification / design including carriage of materials with in all leads, lifts and other incidentals as per entire satisfaction of Engineer-in-charge. |
| 15 | Providing and fixing 100mm (one hundred millimetre) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer - in- charge . |
| 16 | Providing and fixing 75mm (seventy five millimetre) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer - in- charge . |
| 17 | Providing and fixing 100x10mm (one hundred into ten millimetre) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer - in- charge . |
| 18 | Providing and fixing 75x10mm (seventy five into ten millimetre) aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer - in- charge . |
| 19 | Providing and fixing 150x16 mm (one hundred fifty into sixteen millimetre) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. as per direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incedentals. |
| 20 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 21 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including carriage of materials with in all leads, lifts and other incidentals as per entire satisfaction of Engineer-in-charge. |
| 22 | Providing and fixing 19mm (nineteen millimetre) thick water proof termite resistant commercial board box and its shelves including 19 mm (nineteen millimetre) thick commercial board shutter with back side of the cabinet of 8 mm (eight millimetre) thick ply and cut portion of the shelves shall be finished with 6mm (six millimetre) hard wood edging complete including piano hinges and other accessories including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 23 | Finishing wall with water proofing cement paint of approved brand and manufacture of snowcem/apox of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including carriage of materials within all leads and lifts and other incidentals. |
| 24 | Providing two coats (excluding priming coat) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of all dirt,dust and other foreign matter and including a coat of wood filler including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer-in-charge. |
| 25 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (at the rate of zero point nine zero litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/ 10 sqm (at the rate of eight zero litre per ten square metre) of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals. |
| 26 | 6mm (six millimetre) cement plaster to ceiling in cement morter 1:3 (one cement : three Fine sand) including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 27 | 20mm (twenty millimetre) cement plaster in single coat on the fair side of brick/concrete /stone walls for interior plastering upto floor all level including arises, internal rounded angles, chamfers and /or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth in cement mortar 1:4 (one cement : four sand) including carriage of materials with in all leads, lifts and other incidentals as per direction and entire satisfaction of Engineer - in- charge . |
| 28 | Providing and fixing White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (five hundred eighty into four hundred forty millimetre) with integral type foot rests water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hundred millimetre) sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, Perryware /jaquar/ Hindware/ Cera or equivalent No 2071 or its equivalent with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: including carriage of materials with in all leads, lifts and other incidentals as per entire satisfaction of Engineer-in-charge. |
| 29 | Providing and fixing vitreous china wash down water closet (European type W.C. pan) with internal P or S trap, including jointly the trap with soil pipe in cement mortar 1:1 (one cement isto one sand) seat and cover to be measured and paid for separately, Anglo Indian (Universal Closet).Perryware /jaquar/ Hindware/ Cera or equivalent with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: including carriage of materials with in all leads, lifts and other incidentals as per entire satisfaction of Engineer-in-charge. |
| 30 | Providing and fixing water 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming1,Perryware /jaquar/ Hindware/ Cera or equivalent with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 31 | Providing and fixing 15 mm (fifteen millimetre) nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality cenforming to IS 8931 a) 15 mm nominal bore as per the directions and satisfactions including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 32 | Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm (forty five centimetre) length 15 mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 33 | Providing and fixing PTMT jet spray of approved quality and colour with 1.00 mtr. (one meter) Tube including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 34 | Providing and fixing 110mm (one hunderd ten millimetre) dia. high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 35 | Providing and fixing 110mm (one hunderd ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 36 | Providing and fixing 110mm (one hunderd ten millimetre) dia PVC door bend ISI marked insertion rubber washer 3mm (three millimetre) thick, bolts and nuts complete including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 37 | Providing and fixing to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors 15mm (fifteen millimetre) nominal bore as per the directions and including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 38 | Providing and fixing electric water geyser of approved quality and capacity as per the directions and satisfactions including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in- charge. |
| 39 | Providing and laying in trenches galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors 20mm (twenty millimetre) nominal bore as per the directions and satisfactions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. |
| 40 | Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen millimetre) C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 450x300 mm (four hundred fifty into three hundred millimetre) Perryware /jaquar/ Hindware/ Cera or equivalent as per the directions and satisfactions of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. |
| 41 | Providing and fixing 110 mm X 90 mm (one hundred ten into ninety millimetre) PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete including carriage of materials with in all leads, lifts and other incidentals. |
| 42 | Providing and fixing 32mm (thirty two millimetre) dia. Lead waste pipe for wash basin or sink complete including carriage of materials with in all leads, lifts and other incidentals as per entire satisfaction of Engineer-in-charge. Please Enable Macros to View BoQ information |
