|
| 1 | Repair of Godown |
| 2 | Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 3 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size). |
| 4 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size). |
| 5 | Repair of rolling shutter with replacement of shutter spring incl. removal of old spring in the existing rolling shutter incld. Cost of new spring |
| 6 | Repair of rolling shutter with using any material such as bend repair , tightening of spring,boltand screw etc complete |
| 7 | Renewing glass panes, with putty and nails wherever necessary: Float glass panes of thickness 4 mm |
| 8 | Supply and installation of Multi Rib Proofing/cladding Sheet Manufacture out of 0.50mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvaiumeseel (as per 150gsm zinc aluminum coated 550Mpa tuekd strength) confirming to IS: 1397/astm A-792 sheet to have wide pens 30mm high NB at 250 centre and centre width of 1020mm shets be casted with regular modified plyster system on a continuous with line on centre for face and with a polyster coating respectively sheet shall have proportionality with siphoned plate at made at to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. The sheet shall be supplied in cost one length and foe a minimum up to 12mts with all scaffolding. Add extra for 0.60mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvaiumeseel sheet in place of 0.50mm thick |
| 9 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. |
| 10 | Patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects. |
| 11 | Refebrication work with existing steel work including cutting, welding & refebrication as per requirement with fixing at site complete as per direction of Engineer In charge |
| 12 | Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide |
| 13 | Electrification |
| 14 | Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm. nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 KV grade and 1.5 sq. mm. nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 KV grade (IS : 694) of approved make on surface ISI marked(IS-19427-P-II) PVCcasing capping and its accessories, round tiles, 18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in switch board & false ceiling point 6 A switch, 3.0 mm. thick ISI marked phenolic laminated sheet, zinc plated/brass screw, cup washers, making connections, testing etc. as required. Short point (upto 3mtr.) Group-2 |
| 15 | (a) Short Point (upto 3 mtr.) |
| 16 | (b) Medium Point (upto 6 mtr.) |
| 17 | (c) Long Point (upto 10 mtr.) |
| 18 | Wiring for 3 pin 5 amp light plug point with 1.5 sqmm. nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 KV grade and 1.5 Sq. mm. nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 KV grade (IS:694) of approved make in surface/recessed ISI marked medium duty PVC conduit and it's accessories, 18 SWG M.S. box with earth terminal, screwless cage connectors for neutral looping in swith board & falce ceiling point, 6 A swith, 6 A socket, 3.0 mm thick phenolic laminated sheet, zinc plated/ brass screws, cup washers, making connections, testing etc. as required on board. Grade-II. |
| 19 | Providing & Fixing of Street light bracket made out from following size of ' B ' class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004) with heavy duty pole clamp, Saddles suitable fastners etc. As required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure 40 mm Dia. |
| 20 | S&Ffollowingsizes(dia.)ofISImarkedmediumdutyPVCconduitalongwithaccessoriesinsurface/recessedusingsaddles,clamps,fastenerasrequiredincludingcuttingthewall,coveringconduitand making good the same as required. 25mm |
| 21 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor ISI marked (IS:694) of 1.1 kV grade and approved make in existing surface or recessed conduit/casing capping including making connections etc. as required. Group p-2 |
| 22 | 1 x 1.5 sq.mm |
| 23 | 2 x 2.5 sq.mm |
| 24 | 2 x 4.0 sq.mm for powder circuit |
| 25 | Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it's own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 16.0 Sq. mm 4 Core. |
| 26 | P&F two pin energy efficient compact flourscent lamp in existing holder/fixture as required. 36 watt 4 pin Group-II |
| 27 | P&F 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/C/D tripping characterstic) ISI marked IS 8828 (1996)/ conforming to IEC 60898 in existing boards/sheets including making connections with lugs, testing etc. as required 6 A to 32 A rating (Havells, HPL, SSK, Anchor, Khaitan).Grade-II. |
| 28 | P&F 240/415 V isolator conforming to IS:13947-III/IEC 60947-3 on existing board/sheet including making connections with lugs, testing etc. as required 63 A rating (Havells, HPL, SSK, Anchor, Khaitan) Grade-II. |
| 29 | P&F Recessed/Surface mounting heavy duty horizontal type sheet steel Distribution board phophatised/ power painted complete with 100 A copper bus bar, shorting link, neutral link, earth link and din bar, conforming to IS13032 & IS8623 including making internal DB terminations with copper lugs, testing etc. as required Single door (single phase) 12 Way. Grade-II. |
| 30 | Providing and fixing of non modular power plug point accessories as per PWD specification for electrical Works with 18 SWG G I box of size 175 x 100 x 60 mm with earthing terminal/connector on recessed/surface with suitable size phenolic laminated sheet (IS : 2036 - 1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outlet [ as per detailed in respective item in BSR], making connection , testing , etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 31 | Providing & Fixing of ISI marked (IS:2268-1994) ding dong/musical chime bell as per PWD specification for electrical Works, including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\"attached with this BSR . |
| 32 | Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 1200 mm Sweep BEE 2 Star rated (service value >=4.5 to< 5 ) |
| 33 | Providing & Fixing of energy efficient direct fit (Retrofit) Polycarbonate/Extruded Al Base Housing & diffuser SMD Mid Power LED tube (withintegral driver), on existing fixture. Power Consumption of 18W / 20Wsystem lumen efficacy ≥ 110 lm/Watt output, internal surge protection of2.5 KV ,THD < 15% ,p.f.≥0.95,CRI >80 , life time of minimum 35000Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure \\"A\\" attacheded with this BSR. 4', 18/ 20 Watt LED Tube Without Batten (Extruded Al Base) |
| 34 | Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaireon existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy >=120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor >0.95 driver Efficiency >85% ,THD(I) <10% Humidity 10% to 90% RH Working Temp -5C to 45C . driver current <1000mA shown in LM79 report. The luminaire shall be BIS certified and T.C. certified. Life Expectancy Equal or more than 50000 burning hrs with Minimum70% lumen maintened ,color Rendering Index >70 and CCT 5700K+355K. Surge protection shall be min ≥ 4 KV internal and min 10 KVexternal. driver should be Phase to phase protection of 440 V for 4Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . LED Street Light fixture 30 Watt |
| 35 | C.C.Interlocking Block Road |
| 36 | Dismantling of existing structures like culverts, bridges, retaining walls and other structures comprising of brick masonry, including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 m as per MoRTH Specification Clause 202. Dry Brick Pitching or Brick Soling |
| 37 | Compacting original ground supporting subgrade Loosening of the ground upto a level of 300 mm below the subgradelevel, watered, graded and compacted in layers to meet requirement of Tables 300-1 and 300-2 for subgrade construction as per MoRTH Specification Clause 305.3.4 |
| 38 | Water Bound Macadam Sub-base/base with Stone Screening WBM Grading 1 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening & binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 1 as per MoRTH Specification Clause 404. Using Crusher Broken Aggregate By Manual Means |
| 39 | Interlocking Concrete Block Pavement with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge Blocks (measurements shall be made inner to inner side of edge blocks) Providing and Laying of Interlocking M-30 grade Concrete Block Pavements having thickness 80 mm as per drawings and as per IS 15658:2006.and all materials shall conform to MoRTH Specification Clause 602 with M-30 Grade 0.30 Mtr x 0.30 Mtr x 0.15 Mtr Edge Blocks. Category 'A' : Dentated units to key into each other on all four faces Zigzag shape as per IRC:SP:63-2004 |
| 40 | Fillling in foundation trenches as per drawing and MoRTH specification Clause 304.3.7 Sand filling Please Enable Macros to View BoQ information |