|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. |
| 2 | All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth. sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lift |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 5 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 8 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 9 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 11 | Foundations, footings, bases of columns, etc. for mass concrete. |
| 12 | Walls any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 13 | Suspended floors, roofs, landings, balconies and access platform |
| 14 | Edges of slabs and breaks in floors and walls (Under 20 cm wide) |
| 15 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 16 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 17 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. |
| 18 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 19 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 20 | 300x16 mm |
| 21 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 22 | 250x10 mm |
| 23 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 24 | 125 mm |
| 25 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 26 | Twin rubber stopper |
| 27 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 28 | G.I. pipes |
| 29 | 12 mm cement plaster of mix : |
| 30 | 1:4 (1 cement: 4 fine sand) |
| 31 | 12 mm cement plaster finished with a floating coat of neat cement of mix : |
| 32 | 1:4 (1 cement: 4 fine sand) |
| 33 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 34 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 35 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 36 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be \measured for payment). |
| 37 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory Yvindows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 38 | Frame size 50 x 100 mm |
| 39 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 40 | 30 mm thick |
| 41 | Supplying, erection & fixing of Name/Sign board of size (5'x3') or above installed on post & frame made of 40mm dia G.I. Pipe & 2 mm thick G.I. plate as base on which 4mm thick foam sheet is fixed with necessary matter inscribed with Vinyl Sticker with the help of screws or welding wherever needed and erected on place fixing with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) including the cost of shuttering and earth work etc. as per the direction of Engineer-In-Charge. |
| 42 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 43 | Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 44 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. |
| 45 | 30 mm thick plain PVC door shutters |
| 46 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 47 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 48 | Applying priming coat |
| 49 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works |
| 50 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 51 | Two or more coats on new work |
| 52 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : |
| 53 | Two or more coats on new work |
| 54 | Providing and fixing G.I. chain link fabric fencing of required width inmesh size 50x50 mm including strengthening with 2 mm dia wire ornuts, bolts and washers as required complete as per the direction of Engineer-in-charge. |
| 55 | Made of G.I. wire of dia 4 mm |
| 56 | Providing and fixing P.V.C. low level flushing cistern with manuallycontrolled device (handle lever) conforming to IS : 7231, with all fittingsand fixtures complete. |
| 57 | 10 litre capacity - White |
| 58 | Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C. waste fittings complete. |
| 59 | Semi rigid pipe (32 mm dia) |
| 60 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work |
| 61 | 25 mm dia nominal bore |
| 62 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) |
| 63 | 25 mm nominal bore |
| 64 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 65 | 45 cm length (15 mm nominal bore) |
| 66 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : |
| 67 | 25 mm nominal bore |
| 68 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 69 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 70 | 15 mm nominal bore |
| 71 | Providing and fixing PTMT pillar cock of approved quality and colour. |
| 72 | 15 mm nominal bore, 107 mm long, weighing not less than 110 gms |
| 73 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as. |
| 74 | Group C |
| 75 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required |
| 76 | a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 77 | b) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 78 | c) 4 X 6 sq. mm + 2 X 6 sq. mm earth wire |
| 79 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required |
| 80 | Supplying and fixing metal box of 150mm X 75mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 A socket outlet and 5/6 A piano type switch, connections, painting etc. as required. |
| 81 | Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required |
| 82 | Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required |
| 83 | Installation testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required. |
| 84 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required |
| 85 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required |
| 86 | a) Upto 450 mm sweep |
| 87 | Supplying and fixing PVC batten/ angle holder including connections etc. as required |
| 88 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 89 | a) 8 way , Double door |
| 90 | Supplying and fixing following way, horizontal type three pole and neutal sheet steel MCB distribution board 415V, on surface/recess complete with tinned ocpper bus bar neutral bar, bus bar, earth bar din bar interconnetion powder painted including earthing etc as reqd. (But without MCB/RCCB/Isolator) |
| 91 | a) 6 way (4+18) , Double door |
| 92 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required |
| 93 | a) Single Pole |
| 94 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required |
| 95 | a) 40 Amps |
| 96 | b) 63 Amps |
| 97 | Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required |
| 98 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required |
| 99 | Supplying of LED 20 Watts Batten /Tubelight wipro Garnet with lamp 20 W LED 4ft cool day light (6500 K) with 2000 lumen or its equivalent. |
| 100 | Supplying of 10 W LED bulk head luminaire, similar to Murphy 10W Oval Shape IP54 Water proof cool white or equvilant to IS specification. |
| 101 | Supplying of LED bulb of 9 Watts B22 similar to Panasonic 9W cool day light (6500k) or equivalent to ISI specification. |
| 102 | Supplying and fixing of 50 Watts LED Street IP 65, similar to PE Glass 50 Watts Lens corded Electric LED Street light water proof IP65 Full Poly carbonate body 140 per watt Lumens or its equivalent to IS specification. |
| 103 | Supply of exhaust fan of size 230 mm sweep similar to USHA Aeroclean of its equivalent to IS specification. |
| 104 | Supplying of BEE 1 star rating, with ISI, A.C. Ceiling fan 1200 mm sweep,with all accessories . (Similar to Orient Electric APEX FX) or equivalent to IS specification. |
| 105 | Providing and fixing pole mounting water proof cable looping out box made out of SMC and of size 280mm x 180mm x 60mm for providing and hinged door and locking arrangement i/c providing and fixing the following mounting and fixing the box in to the concrete collar/street light pole with suitable nuts and bolts. |
| 106 | 6ASP MCB -01 No. (30 amps rating connector 4 way-01 No.) |
| 107 | Supplying, installation, testing and commissioning of indoor type wall mounted cubical panel LT panel board with load bank G frame size 250amps \\"G\\" frame double door suitable for four pole outgoing MCCB having 01 No. 100 amps MCCB as incoming and 3 Nos. MCCB 40 amps and 01 No 63 Amps outgoing with cable alley (for G frame panel boards), prewired meter module for \\"G\\" frame panel boards with digital voltmeter , digital ammeter selector switch, CTs control fuse and indicating lights with connection etc as reqd Make Havells or its equivalent. |
| 108 | Supplying installation, testing and commissioning of ASHLOK make SEE brand safe earthing electro type-19, 50mm dia length 2 mtrs and inner space to be filled with crystaline conductive mixture including filling up with elelctrodite (Back fill compound ) as reqd for safe earth electrode and providing masonary enclusure with cover plate having locling arrangement etc as reqd. Please Enable Macros to View BoQ information |
