Tender For Stage Contract For Maintenance Of Roads And Bridges For The Year 2026-27, Under The Territorial Jurisdiction Of R&B Divisiona Karnagar., Srinagar-Jammu And Kashmir

TDR : 55020361

Tender Notice
BOQ

8 Days Left

Srinagar , Jammu And Kashmir

Tender Brief : Tender For Stage Contract For Maintenance Of Roads And Bridges For The Year 2026-27, Under The Territorial Jurisdiction Of R&B Divisiona Karnagar.

Document Fees
₹ 600 /-

EMD
₹ 20000.0 /-

Tender Value
Refer document

Submission Date
17-04-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Engagement of Mazdoor./Labour
2	Engagement of Carpenter
3	Engagement of Mason
4	Engagement of Plumber.
5	Engagement of Black Smith.
6	Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil : 1 meter from cutting edge
7	Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :
8	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.
9	Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.
10	Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.
11	Removal of unhygienic materials (so classified by the site engineer) from designated sites and its disposal as per directions, all inclusive.
12	Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.
13	Providing & laying of stone soling hand packed in foundation and plinth incl ramming, watering, compaction & lead lifts all carriages upto site of work complete.
14	Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:
15	1:1½:3 (1 cement :1½ coarse sand: 3 graded stone aggregate 20 mm nominal size)
16	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
17	1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
18	1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
19	Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete
20	Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level
21	1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
22	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
23	Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
24	Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
25	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more.
26	Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded
27	Centering and shuttering including strutting, propping etc. and removal of form for:
28	Foundations, footings, bases of columns etc. for mass concrete.
29	Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.
30	Suspended floors, roofs, landings, balconies and access platforms.
31	Shelves (cast-in-situ)
32	Lintel, beams, plinth beams, girders, bressumers and cantilevers.
33	Columns, pillars, piers, abutments, posts and struts.
34	Stairs (excluding landings) except spiral staircases.
35	Spiral staircases (including landings)
36	Arches, domes, vaults upto 6 m span
37	Edges of slabs and breaks in floors and walls
38	Under 20 cm wide
39	Above 20 cm wide
40	Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand)
41	Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level
42	Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in
43	Cement mortar 1:3 ( 1 cement : 3 coarse sand)
44	Cement mortar 1:4 ( 1 cement : 4 coarse sand)
45	Extra for half Brick masonry in superstructure above plinth level upto floor V level.
46	Dry random rubble masonry with hard stone in foundation and plinth With bond stone. (Quarry)
47	Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels
48	Raj Nagar plain white marble/Udaipur green marble/zebra black marble (16mm)
49	(Area of slab upto 0.5 sqm)
50	(Area of slab over 0.5 sqm)
51	Granite of any colour or shade (18mm)
52	(Area of slab upto 0.5 sqm)
53	(Area of slab over 0.5 sqm)
54	Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.
55	Marble Work
56	Granite Work
57	Extra for fixing marble / granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete
58	Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): KD Wood
59	Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position Budloo / Fir wood
60	Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. complete Popular Wood
61	Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart (frames to be paid separately) including fixing 50x12 mm beading complete with First class kail wood.
62	Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.
63	25mm thick with 12.5 mm nominal size stone aggregate.
64	40mm thick with 20 mm nominal size stone aggregate.
65	50 mm thick with 20mm nominal size stone aggregate.
66	Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing, cleaning and curing complete, on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Light shade using white cemen
67	Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
68	Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete
69	Size of tile 600x600 mm
70	Size of tile 1000x1000 mm
71	Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).
72	Size of tile 600x600 mm
73	Size of tile 1000x1000 mm
74	Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
75	Size of tile 600x600 mm
76	Size of tile 1000x1000 mm
77	Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete
78	Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required
79	0.63 mm thick with zinc coating not less than 275 gram/m2
80	0.50 mm thick with zinc coating not less than 275 gram/m2
81	Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete.
82	0.63 mm thick with zinc coating not less than 275 gram/m2
83	0.50 mm thick with zinc coating not less than 275 gram/m2
84	Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.
85	1.60 mm thick with zinc coating not less than 350 gram/m2
86	1.25 mm thick with zinc coating not less than 350 gram/m2
87	1.00 mm thick with zinc coating not less than 275 gram/m2
88	Providing and fixing 15cm wide 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete.
89	0.80 mm thick with zinc coating not less than 275 gram/m2
90	0.63 mm thick with zinc coating not less than 275 gram/m2
91	Providing and fixing UV stabilized fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts and nuts 8mm dia. G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS: 10192 and IS: 12866. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.
92	2mm thick corrugated (2.5\\" or 4.2\\" or 6\\") or step-down (2\\" or 3\\" or 6\\") as specified.
93	2mm thick flat
94	Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
95	In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete.
96	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
97	Providing and fixing of KHATAM BANDI ceiling of first class budloo/fir wood excluding the cost of frame work which is to be paid separately.
98	Changez Khani
99	Chaar Gul
100	Chaar Phool
101	Pahal Gardan
102	Dawaz-dal-i-girde
103	Paanch Murabah
104	12mm Cement plaster of mix
105	1 : 4 ( 1 cement : 4 fine sand)
106	1 : 6 ( 1 cement : 6 fine sand)
107	15mm Cement plaster on the rough side of single or half brick wall of mix
108	1 : 4 ( 1 cement : 4 fine sand)
109	1 : 6 ( 1 cement : 6 fine sand)
110	6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)
111	Pointing on stone work with cement mortar 1 : 3 (1 cement : 3 fine sand)
112	Flush/Ruled Pointing
113	Raised and cut pointing
114	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre,two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer's specifications
115	Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface.
116	Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm)
117	Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm)
118	Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers' specifications: Two or more coats applied @ 1.25 liter/10sqm over and including one coat of special primer applied @ 0.75liter /10sqm
119	Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture
120	Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture
121	Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)
122	Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.
123	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.
124	Two or more coats on new work
125	Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
126	Varnishing with varnish of approved brand and manufacture:
127	Two or more coats of glue sizing with copal varnish over and under coat of flatting varnish.
128	Two or more coats of glue sizing with spar varnish on an under coat of flatting varnish
129	Lettering with black Japan paint of approved brand and manufacture.
130	Re-lettering with black Japan paint of approved brand and manufacture.
131	Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
132	1 mm thick
133	2 mm thick
134	Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.
135	One coat
136	Two coats
137	Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.
138	One coat
139	Two coats
140	Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.
141	With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter
142	With ready mixed red oxide zinc chromatic on steel / iron works having VOC content less than 250 grams/ liter
143	With water thinnable cement primer on wall surface having VOC content less than 50 grams/liter
144	Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
145	Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
146	Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead
147	With cement mortar 1:4 (1 cement : 4 fine sand)
148	With cement mortar 1:4 (1 cement : 4 coarse sand)
149	Fixing chowkhat in existing opening in brick/RCC wall with dash fasteners/chemical fasteners of appropriate size (3 nos on each vertical member of door chowkhats and 2 nos. on each vertical member of window chowkhats), including cost of dash fasteners/chemical fasteners.
150	Making the opening for door/window/clerestory window in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete, to match existing surface i/c disposal of mulba/ rubbish to the nearest municipal dumping ground.
151	Renewing glass panes, with putty and nails wherever necessary including raking out old putty :
152	Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm)
153	Float glass panes of thickness 5.0 mm(weight not less than 12.5 kg/sqm)
154	Renewing glass panes, with wooden fillets wherever necessary :
155	Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)
156	Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)
157	Renewing glass panes and re-fixing existing wooden fillets:
158	Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)
159	Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)
160	Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.
161	Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.
162	Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge.
163	Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge:
164	1:3:6 or richer mix (i/c equivalent design mix)
165	1:4:8 or leaner mix (i/c equivalent design mix)
166	Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar
167	Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) From brick work in cement mortar
168	.Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead
169	Of area of 3 sqm. and below
170	Of area beyond 3 sqm.
171	Dismantling steel work in single sections including dismembering and stacking within 50 meters lead in R.S. Joists
172	Dismantling wood work in frames, trusses, purlins and rafters upto 10 meters span and 5 meters height including stacking the material within 50 meters lead.
173	Of sectional area 40 sqcm. and above.
174	Of sectional area below 40 sqcm.
175	Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead.
176	For thickness of tiles 10 mm to 25 mm
177	Demolishing RCC work by mechanical means & stockpiling at designated locations & disposal of dismantled materials upto a lead of 1 kilometer, stacking serviceable & unserviceable material separately including cutting reinforcement bars
178	Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets
179	20 mm dia ( heavy type)
180	25 mm dia ( heavy type)
181	Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts
182	Painting road surface marking with adequate no. of coats to give uniform finish with read mixed road marking paint conforming to IS: 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete.
183	New work (Two or more coats)
184	Old work ( One or more coats)
185	Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).
186	Providing and fixing tiled False Ceiling of specified materials of size 595x595mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms/sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main “T” at 600mm center to center to form a grid of 1200 x 600mm and secondary cross “T” of length 600mm and size 24x25 mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.30mm and laying false ceiling tiles of approved texture in the grid including, wherever, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27x37x 25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm GI adjustable rods with galvanized butterfly level clips of size 85x30x0.8 mm spaced at 1200mm center to center along size 85x30x0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (The rate is excluding the cost of tiles which will be paid for separately).
187	GI Metal Ceiling Lay in plain Tegular edge Global white colour tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.
188	Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto plinth level including curing. One face dressed
189	Fine chisel dressed
190	Rough chisel dressed
191	Extra for fine chisel dressed Devri Stone in square or rectangular Pillars
192	Providing and laying rough chisel dressed Devri Stone in kerbs, of size 200x200 mm face with chamfer in cement mortar 1: 6 (1 cement : 6 coarse sand) including curing.
193	Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). imported kail wood: (35mm Thick)
194	Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge (35mm Thick)
195	Providing and fixing wire gauze using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows including cost of beading complete.
196	Providing and fixing of chicken mesh wherever required of specified size including cost of beading and nails complete.
197	Providing and fixing of Buj tile cladding of required pattern. Shade and design over 20mm thick cement plaster 1:3 mix (1 cement: 3coarse sand) including jointing with neat cement slurry complete.
198	Providing and fixing of Interlocking/Chequered precast cement concrete tiles colored(rubber finish) in foot paths & courtyards jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and cleaning etc. complete on 20mm thick layer of dry sand .
199	40mm thick.
200	50mm thick.
201	75mm thick.
202	Providing and fixing A.C.P 3mm multi coloured (Fire retardant) in partitions, ceilings, shutters frames etc in panels of min size 600mm x 600mm including cost of rubber,neoprene gasket ,waterproof silicon sealent , or as required at site as per the directions of concerned engineer in charge.complete job
203	Engagement of tipper including fuel charges complete.
204	Engagement of excavator (JCB) in all terrains including fuel charges complete.
205	Engagement of hand cart all complete
206	Providing and fixing of wardrobe, almirah, drawer locks (Sample to be approved by EIC)
207	Providing and fixing of aluminum double channel with wheel set for sliding glass window of approved quality of following sizes.
208	20 mm
209	25 mm
210	Providing and fixing of door closer capsule type of standard make
211	Providing and fixing of door closer spring type of standard make
212	Providing and fixing of following fittings
213	Aldrop
214	Tower Bolt 100mm
215	Tower Bolt 150mm
216	Handle 100mm
217	Handle 150mm
218	I Hook
219	Hinges 75mm
220	Hinges 100mm
221	Lockable sliding Aldrop 250-300mm long (Godrej/ Link/Ramson or equivalent)
222	Providing and fabrication of ward robes (ornamental) of approved quality 19mm Ply board in sides, shelves and wherever required including 6mm ply wood on back and 19MM ply board in shutters, inside and outside of shutters finished with Dulmica sheeting of approved quality and color on exposed face of approved design and drawings including (painting two or more coats of synthetic enamel paint of approved quality and color inside) including cost of following aluminum fittings and locks of approved make. 15mm dia. M.S. pipe chromium plated with necessary brackets 4'-0\\" length and including all other necessary accessories complete in all respects. Including fixing with dashfasteners wherever required (For payments front face to be measured).
223	50-60 cm deep
224	40-45 cm deep
225	20-30 cm deep
226	extra for using ply to ply instead of board (Face measurement)
227	extra for using lining instead of painting on internal surface as per measurement - 12mm
228	Extra for using 10-12mm ply instead of 6mm on back side of Wardrobe/ Kitchen cabinets
229	Extra for using MDF shuttes ornamental type of required thickness instead of ply/ pine shutters (Face measurement)
230	Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.
231	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.
232	Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C automatic flushing cistern, with fittings, standard size G.I./ PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and in C.P brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required:Range of three squatting plates with 10 liter P.V.C. automatic flushing cistern.
233	Providing and fixing wash basin with CI/MS/ brackets including painting of fittings and brackets, cutting and making good walls wherever required white vitreous china wash basin size 630x450mm with 32mm dia. C.P. brass union & flexible waste pipe (Jaquar/ Hindware/ Cera/ Kerrovit or equivalent)
234	Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete. (Sample to be approved by EIC)
235	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265mm size respectively.
236	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x460mm bowl depth 200mm
237	Providing and fixing white vitreous china laboratory sink including making all connections excluding cost of fittings Size 600x450x200 mm.
238	Providing and fixing of white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm respectively with automatic flushing cistern with standard flush pipe and C.P brass spreaders with brass unions and G.I clamps complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required One urinal basin with 5 liter white PVC automatic flushing cistern (Sample to be approved by EIC)
239	Providing and fixing of C.P grating 100mm size. ISI
240	Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings and clamps including cutting and making good the walls etc. internal work (Exposed on Walls) (Sample to be approved by EIC)
241	15mm dia. Nominal bore
242	20mm dia. Nominal bore
243	25mm dia. Nominal bore
244	32mm dia. Nominal bore
245	40mm dia. Nominal bore
246	50mm dia. Nominal bore
247	Providing and fixing of G.I pipes (class B pipes) complete with G.I fittings excluding trenching and refilling etc. (external work) (Sample to be approved by EIC)
248	15mm dia. Nominal bore
249	20mm dia. Nominal bore
250	25mm dia. Nominal bore
251	32mm dia. Nominal bore
252	40mm dia. Nominal bore
253	50mm dia. Nominal bore
254	65mm dia. Nominal bore
255	80mm dia. Nominal bore
256	100mm dia. Nominal bore
257	Providing and fixing of following G.I. fittings. 15 mm nominal bore.(Sample to be approved by EIC)
258	Elbow
259	Union
260	pvc plug/ G.I Plug
261	Nipple
262	50mm long.
263	75mm long
264	100mm long
265	150mm long
266	Socket
267	Reducer
268	15mm-20mm
269	20mm-25mm
270	20mm-32mm
271	25mm-32mm
272	Providing and fixing of following G.I. fittings. 20 mm nominal bore.(Sample to be approved by EIC)
273	Elbow
274	Union
275	pvc plug/ G.I Plug
276	Nipple
277	50mm long.
278	75mm long
279	100mm long
280	150mm long
281	Providing and fixing of PVC connection with C.P. brass unions
282	300mm long.
283	450mm long
284	600mm long
285	Providing and fixing ball valve (brass) of approved quality complete (Sample to be approved by EIC)
286	15mm dia.
287	20mm dia.
288	25mm dia.
289	40mm dia.
290	Providing and fixing gate valve (brass) of approved quality complete (Sample to be approved by EIC)
291	15mm dia.
292	20mm dia.
293	25mm dia.
294	40mm dia.
295	50mm dia.
296	Providing and fixing of Ball cock of approved quality and make with plastic float. (PVC type)
297	15 mm
298	20 mm
299	Providing and fixing of flexible PVC Pipe
300	For Washbasin
301	For Urinal
302	Providing and fixing of Ball cock of approved quality and make without plastic float.
303	15 mm
304	20 mm
305	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank
306	Providing and fixing of C.P. Cups for C.P. fittings.
307	Providing and fixing of C.I. manhole cover heavy duty of following sizes.
308	12\\"x12\\"
309	18\\"x18\\"
310	24\\"X24\\"
311	Providing , installation, commissioning and testing Hot water Geyzer of approved make including fixing with bolts/ fasteners/PVC connection etc. Venus, Recold, Hindware, Havells, Jaquar, Crompton of required capacity fittings and fixtures all complete wherever required in the course of completion. complete job.
312	50 Litre
313	35 Litre
314	25 Litre
315	Providing and fixing of PVC connection for wash basins, geysers etc.
316	30-45 cm in length
317	60-90 cm in length
318	Providing and fixing Geyser elements (as per Geyser type) dry/ wet
319	Providing and fixing Geyser thermostat
320	Providing and fixing Drain plug with washer.
321	Providing and fixing Safety valve for geysers.
322	Providing and fixing water washers for geysers.
323	Providing and fixing of auto thermo cut for geyser.
324	Providing and fixing of pressure water ball Valve
325	Providing and fixing C.P. brass bib cock of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 15mm nominal bore with flange
326	Short Body
327	Long Body
328	Providing and fixing of 15mm size chromium plated cast brass sink mixer Wall mounted/ Counter mounted of approved quality.(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)
329	Providing and fixing of hand shower with chain of approved quality.(Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent)
330	Providing and fixing of shower including shower arm of approved quality (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with flange
331	Providing and fixing of 15mm size chromium plated cast brass wall mixer Non telephonic of approved quality. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with flange
332	Providing and fixing of 15mm size chromium plated cast brass wall mixer with bend pipe for head shower of approved quality. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with flange
333	Providing and fixing Towel ring 30mm. (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) with flange
334	Providing and fixing Towel rod (Hindware/ Jaquar/ Kerrovit/ Asian/ Marc or equivalent) 600mm long
335	Providing and fixing Soap Dish case
336	Providing and fixingToilet Paper Holder
337	Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete
338	Providing and fixing of pvc manhole cover of approved make of following sizes. (Heavy type)
339	12\\"x12\\"
340	18\\"x18\\"
341	24\\"X24\\"
342	Construct brick masonry man hole in cement mortar 1:4 (1 cement: 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size) foundation concrete (1:4:8) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size finished with a floating coat of neat cement complete. (Depth as per site requirement)
343	Size 90 x 90 cm deep including RCC/C.I. manhole cover medium duty with frame of size 60x60mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects.
344	Size 60 x 60 cm deep including RCC/C.I. manhole cover medium duty with frame of size 60x60mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects.
345	Size 45 x 45 cm deep including RCC/C.I. manhole cover medium duty with frame of size 45x45mm size/ Concrete Slab. With F.P.S. bricks with class designation 75 and with crushed stone aggregate complete in all respects.
346	Providing and fixing of PVC pipe (Type \\"B\\") in proper gradient in excavated trenches including jointing and refilling the excavated material complete including cost of excavation. (Sample to be approved by EIC)
347	150mm dia. Pipe (Including necessary fittings)
348	100mm dia. Pipe
349	75mm dia. Pipe
350	50mm dia. Pipe (Push Type)
351	Providing and fixing of Health Faucet / jet spray with plastic flexible pipe 8 mm dia, 1.5 m long, wall hooked complete as required, including necessary accessories , installation charges and complete in full respect as per the directions of Engineer- in-charge.
352	Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931
353	Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.
354	Providing and fixing of imported wallpapers (Glass cloth or Fabric type) on walls/ceiling of approved quality like cassio, passion, polo or other including cost of fixing material and labour including preparing even surface to provide smooth texture of wall paper complete job confirming to IS 15418 (2003) design approved Engineer Incharge
355	Providing and fixin of PPR Male/ Female Adaptors (All types like elbows, tees etc) (Sample to be approved by EIC)
356	for 25mm dia.
357	for 32mm dia.
358	for 40mm dia.
359	Providing and fixing PPR Unions
360	PPR Union 20mm
361	PPR Union 25mm
362	PPR Union 32mm
363	PPR Union 40mm
364	PPR Union 50mm
365	PPR Union 63mm
366	PPR Union 75mm
367	Providing and fixing PPR ball valves (Sample to be approved by EIC)
368	for 25mm dia.
369	for 32mm dia.
370	for 40mm dia.
371	for 50mm dia.
372	for 63mm dia.
373	Providing and fixing of thermal insulation over following dia G.I Pipes at all heights
374	for 15mm dia.
375	for 20mm dia.
376	for 25mm dia.
377	for 40mm dia.
378	Providing and fixing C.P. two way brass bib cock of approved quality ((Sample to be approved by EIC) 15mm nominal bore
379	Providing and fixing C.P. two way brass 2 way angle valve of approved quality ((Sample to be approved by EIC) 15mm nominal bore
380	Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge. Made of G.I. wire of dia 4 mm
381	Engagement of Hilti for cutting slab, demolishing of concrete etc
382	Providing & fixing of stainless steel (grade 304) railing made of hollow tubes,channels etc including welding grinding,buffing ,polishing & making curvatures & fitting the same with necessary stainless nuts & bolts complete i.e fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc of required size of the top of the floor or the side of waist slab with suitable arrangements as per approval of engineer in-charge.
383	Scientific cleaning & sterilization of Water Storage tanksThe Job involves 6 stage scientific cleaning and sterilization process consisting of Mechanical Dewatering, Hi-Pressure Cleaning, Sludge Removal, Vacuum Cleaning, Antibacterial Spray and finally killing of suspended & floating bacteria by Ultra violet Radiation as detailed below:-1. Dewatering of Tanks:- The Water from the Storage tanks should be pumped out of tanks through Mechanical Dewatering pumps of suitable capacity.2. Exterior Cleaning:- The Roof top, Manholes and External walls of the Water Storage Tanks should be cleaned thoroughly for any traces of dirt, mud and algae present in the close vicinity.3. High Pressure Interior Cleaning:- The interiors of the water storage tanks should be cleaned with high pressure jet which dislodges the layers of dirt and other suspended foreign bodies which may be sticking on the walls. This process will remove the layer of calcination of dirt if any so as to make the interior free of any germs and bacteria. The interiors including the floor , walls and top ceiling of the over head tanks.4. Sludge Removal:- The Dirty water and sludge collected in the previoius operation should be removed using industrial Sludge pumped and disposed off properly away to a safer place so as not to contaminate the water. The floor of water storage tanks should be again cleaned thoroughly using high pressure jet stream so as to remove all the remaining dirt which may be sticking on the floor even after removal of the sludge slurry.5. Drying of tanks:- The water storage tanks should then be dried using industrial Vacuum Cleaners of suitable capacity.6. Antibacterial Spraying:- The inside walls, ceiling and floor of the water storage tanks should then be given the antibacterial treatment which would ensure all interior walls, ceiling and floor surface of the water storage tanks totally germs free.7. Sterilization using Ultra Violet Radiation:- Finally, UV Radiator should be used to ensure the complete wipe out of any bacterial traces which may still be present even after the completion of above processes by giving Ultra Violet Treatment on all Interior SurfacesOver Head Water Storage Tanks/ PVC Water Storage tanks
384	PVC overhead storage tanks
385	Underground Sumps
386	Carriage of materials by way of mechanical transport including loading unloading leads lifts from source to site of work.
387	Aggregates above 40mm for an average lead of 20Kms
388	Aggregates above 40mm for an average lead of 15Kms
389	Aggregates below 40mm for an average lead of 20Kms
390	Aggregates below 40mm for an average lead of 15Kms
391	Sand for an average lead of 20Kms
392	Sand for an average lead of 15Kms
393	Bricks for an average lead of 25Kms
394	Stones for an average lead of 20Kms
395	Erecting water proof pandaals /shamyanas of required area with crewel ceiling, crewel/theme curtains including removal of same after function and carriage of all materials complete.(On rental basis) per Day:-
396	Pandaals (Waterproof) with Theme/Crewel Ceiling & Curtains:
397	Pandaals (Waterproof)with Crewel Ceiling, without curtains
398	Supplying of Indian National Flag conforming to to the flag code of india of fabric shiny knitted polyester of the following size
399	Providing and fixing of MS pipe of dia 50mm with arrangment of pulley with rope 6mm of required length complete job
400	Supply and laying of saw dust (50 Kg Bag) at site including all carriages complete job
401	Supply, laying and spreading of sand mannually including all leads lifts carriages complete job.
402	Hire charges of Genset 2800 wtt for full duration of the event including fuel/Carriages charges all inclusive. Complete job.
403	Hire charges for Fan including Wiring/Electricity/ Fan Charges for full duration of the event.
404	Hire charges for Water coolers including Wiring/Electricity for full duration of the event.
405	Providing and Fixing Unsupported Coloured Flex Display Sheet with subject matter including carriage to venue as directed by EIC
406	Providing and Fixing Coloured Flex Display Sheet with subject matter as directed supported with M.S. Frame including carriage to venue as directed by EIC
407	Providing and Laying Under layment Foam for Matting including carriage to venue as directed by EIC
408	Engagement of Tata Mobile transport for carriage of material including carriage to venue as directed by EIC
409	Hire and laying charges for runners of required size colour and shade including all leads lifts carriages complete job
410	Hire charges for sofas (Three seater) with slip covers etc as directed by EIC including all carriage complete,
411	Hire charges for sofas (Two seater) with slip covers etc as directed by EIC including all carriage complete.
412	Hire and fixing charges buntings of artificial flowers ballons etc to VIP Entrance gate/Row complete job
413	Hire charges of Gas Bukhari with filled gas cylinder including carriages to and fro complete.
414	Uprooting rank vegetation and weeding by digging the area to a depth of 60cm removing all weeds and other growth with root incl. disposal of all rubbish with leads and lifts
415	Crewel Curtain Of Required Colour and Design (Hand Work) 2.5 feet x 7.5 feet
416	Simple Curtain 2.5 feet x 7.5 feet
417	Painting road surface marking with adequate no. of coats to give uniform finish with read mixed road marking paint conforming to IS: 164, on bituminous surface in white/yellow shade including cleaning the surface of all dirt, scales, oil, grease and
418	View/Cutter/Tajeera (Rental basis)
419	Carpet For Dias/ Cultural Programmes and Vip Area Size 10x10(Rental basis)
420	PVC Chairs (Rental Basis)
421	.Excel Matting Runner(Rental basis)
422	Wooden Podium Desk (Rental Basis)
423	V.I.P Chairs (Rental Basis)
424	V.I.P Table (Rental Basis)
425	Refilling of gas in Air Conditioners of any model.
426	Providing and fixing imported laminated wooden flooring with foam including necessary beading/cornices of approved quality required shade as per directions of Incharge Engineer including all leads lifts carriages complete job; all inclusive
427	Dismantling wooden boarding’s in lining of walls and partitions, excluding supporting members but including stacking within 50 meters lead :Thickness above 25 mm upto 40 mm.
428	Providing and fixing of computer table/work stations made in 19 mm thick commercial board with laminated (all surfaces) shutters, of approved brand and shade, pattern and make in frames partitions shelves drawers etc. cost of all hardware accessories/fixture etc. complete job.
429	Providing and Fixing Of Chair Covers of Required Material, Design, Shape and Colour as directed by engineer incharge. Including Fixing Charges all Carriage and costs Complete Job.
430	Scarifying metalled (water-bound) road surface including disposal of rubbish lead upto 50m and consolidation of the aggregate received from scarifying with power road roller of 8 to 10 tonne capacity.
431	Scarifying the existing bituminous road surface to a depth of 50mm and disposal of scarified material within all lifts and lead upto 1 km (by mechanical means)
432	Supplying, stacking and laying water bound macadam base course with stone aggregate 63-45mm size, stone screening 13.2mm size and binding material including screening, sorting, spreading to template and consolidation with power road roller of 8-10 tonne capacity including carriage of all materials as involved upto site of work complete. Finished work to be measured (75mm compacted thickness).
433	Supplying, stacking and laying water bound macadam base course with stone aggregate 53-22.4mm size, stone screening 11.2mm size and binding material as per MORTH specifications including screening, sorting, spreading to template and consolidation with power road roller of 8-10 tonne capacity including carriage of all materials from sources upto site of work complete. Finished work to be measured (75mm compacted thickness).
434	Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.
435	Providing and applying tack coat using hot straight run bitumen of grade VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit on bitumen boiler, cleaning and preparing the existing road surface as per specifications.
436	On WBM @ 0.75 Kg/Sqm
437	On B.T Surface @0.50Kg/Sqm
438	Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equiped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specification to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-charge. 50mm compacted thickness with bitumen of grade VG-10 @ 3.50% (percentage by weight of total mix) prepared in Drum Type Hot Mix Plant of 60-90 TPH capacity including all carriages complete.
439	Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge 25 mm compacted thickness with bitumen of grade 25 mm compacted thickness with bitumen of grade VG10 @5% (percentage by weight of total mix) and lime filler @ 2% (percentage by weight of Aggregate) prepared in Drum Type Hot Mix Plant of 100-120 TPH capacity.
440	Providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete. (6mm thick)
441	Providing and laying of 40mm thick Dense Bituminous Concrete with bitumen @ 5.5% and filler (cement) @ 3% by weight of total mix on prepared surface with specified graded stone aggregate, hot mixing of bitumen with filler and stone aggregate in hot mix plant, transporting the mixed material by tippers to paver and laying the mixed material with paver finisher to the required level and grade and rolling with road roller as per MORTH specifications to achieve the desired density and compaction but excluding the cost of primer / tack coat including removal of existing semidense coat with mechanical scrapper (wherever required) including all carriages and cost of material, labour, testing during execution for quality control and T&P involved for completion of item of work complete as per direction of EIC.
442	Clearance of drains (manual means) by way of removing accumulated / deposited mulba, silt, rubbish vegetation, etc, including disposal of the same beyond municipal limits or as directed by the EIC including loading and unloading etc complete.
443	Providing and applying 2.5mm thick road marking strips (retro-reflective) of specified shade/colour using hot thermoplastic material by fully/semiautomatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
444	Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.
445	Providing and laying of 300mm dia. RCC spun pipes as X - drainage in position to the required slopes and grades including earth work in excavation and refilling the same and providing of proper cushioning including carriages of pipes upto site of work complete.
446	Providing and laying of 300mm dia. M.S pipes as X - drainage in position to the required slopes and grades including earth work in excavation and refilling the same and providing of proper cushioning including carriages of pipes upto site of work complete.
447	Manufacturing supplying and fixing retro reflective sign boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type-IV of ASTM-D-4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC : 67-2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 20cm c/c to back support frame of M.S. angle iron of size 25x25x3mm along with theft resistant measures mounted and fixed with 2 nos. M.S. angles of size 35x35x5mm to a vertical post made upto M.S. Tee section ISMT 50x50x6mm welded with base plate of size 100x100x5mm at the bottom end and including making holes in pipes, angle flats, providing and fixing M.S. message plate of required size steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical M.S.-Tee support to be painted in black and white colours). Backside of aluminum sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coats including all leads and lifts etc. complete as per drawing, specification and direction of Engineer-in-charge.
448	Mandatory/Regulatory sign boards of 900 mm diameter withpart as length of 3750 mm.
449	Cautionary/warning sign boards of equilateral triangular shape having each side of 900 mm support length of 3650mm
450	Note. Any other item not covered in the BOQ, if required to be executed at site, shall be paid strictly as per the rate mentioned in JKSOR-2022/LMR after deducting the contractors depreciation. Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents

Also Visit

Tenders

Jammu And Kashmir Tenders

Construction Tenders

Bridge Construction Tenders

Bridge Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Stage Contract For Maintenance Of Roads And Bridges For The Year 2026-27, Under The Territorial Jurisdiction Of R&B Divisiona Karnagar., Srinagar-Jammu And Kashmir

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Stage Contract For Maintenance Of Roads And Bridges For The Year 2026-27, Under The Territorial Jurisdiction Of R&B Divisiona Karnagar., Srinagar-Jammu And Kashmir

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us