|
| 1 | Road work |
| 2 | Excavation in soil in hilly areas by mechanical/manual means, in all heights and depths, in all kinds of soil including saturated soil comprising of mixed soil, ordinary rock and hard rock. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion, damages to hill side, water pollution etc. and to protect stability of hill side. Rock shall be excavated with chiselling and wedging out of rock (where blasting is prohibited). All earth work in cutting/excavation including rock excavation shall be carried out true to lines, grades, side slopes, width, camber, super-elevation and levels as shown on the drawings and as directed by the Engineer-in-Charge in conformity with the requirements of MORD technical specification for Rural Road, Section. 300 & 1600 to achieve designed formation width including hauling and stacking of materials useful for construction at suitable sites safe manner and disposal of all surplus material to the approved dumping sites through all modes of transportation including head load and animal transport and mechanical means along with its levelling, fine dressing and carriage of machineries, tools, equipment’s and safety measures and other incidentals necessary to complete the work by mechanical means and labour if required. During the mobilization period, contractor should take the advanced x-sec in 15 m (fifteen metre) interval of whole road length in the presence of Engineer-in-Charge or his representative. In case the advanced x-section has been taken in the presence of Engineer-in-Charge representative, in that case the same has to be got approved from Engineer-in-Charge. The land for dumping sites shall be arranged by the contractors himself and nothing extra shall be paid on this account, filling of unevenness blind age and finishing of the road to specified dimensions or as directed by the Engineer-in-Charge for smooth riding. The recovery for stones, whether useful or 7503.531 (Seven Thousand Five Hundred Three point Five Three One) cubic metre at the rate of Rs 300/-only (Rupees three hundred only) per cubic meter amounting to Rs. 22, 51,059.00 only shall be effected on prorata basis in all circumstances. Any loss to the public and private property during the course of excavation shall be the absolute responsibility of the contractor, which shall have to be duly compensated by him in all cases. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 3 | Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and Parapets etcetera in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiselling/wedging out rocks (Where blasting is prohibited) as per drawings and MORD technical specification section 300 and as per direction of the Engineer-in-Charge including setting out, construction of shoring, bracing, removal of stumps and other deleterious materials and disposal of materials up to any leads and lifts including dressing of sides, bottom and back filling in trenches with excavated suitable approved material to the original surface in layer not executing 150 mm (one hundred fifty millimetre) compacted thickness including shoring, strutting, pumping and bailing out water (surface and sub soil water) up to any depth any quantum of water including cleaning of slush which may arise out during dewatering complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 4 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 with all leads as per MORD Technical Specification section 300 complete and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 5 | Providing and laying concrete mechanically mixed and vibrated 1:5:10 (One cement: Five sand: Ten graded crushed stone aggregate 40mm (Forty millimetre) nominal size) for plain/reinforced concrete in open foundation and plinths for similar works complete as per drawing and MORD technical specification section 800, 900, 1200, & clause 1203 and curing complete including the cost of form work and hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 6 | Providing and laying concrete mechanically mixed and vibrated mix 1:4:8 (one cement: four sand: eight graded crushed stone aggregate 40mm (Forty millimetre) nominal size) for plain/reinforced concrete in foundation and plinths or similar works complete as per drawings and MoRD technical specification section 800, 900, 1200 & 1600 and curing complete including the cost of form work and hauling of material within all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 7 | Back filling with granular material behind abutments, wing walls, return walls and retaining walls complete as per drawing and MORD technical specifications section 1200, 1600 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 8 | Providing and laying 100mm dia (One Hundred millimetre diameter) PVC pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, abutments, wing walls, return walls and retaining/breast walls extended through the full width of the structure with slope 1 (V):20 (H) (One vertical : Twenty Horizontal) towards draining face complete as per drawing and MORD technical specification section 700, 1200 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 9 | Construction of embankment with approved material obtained from borrow pits with all lifts, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with all leads as per MORD Technical Specification section 300 & Clause 301 complete and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 10 | Providing and laying concrete mechanically mixed and vibrated PCC (Plain Cement Concrete) M-10 (Ten) 1:3:6 nominal mix (one cement: three sand: six graded crushed stone aggregate 20 (Twenty millimetre) nominal size) for plain/reinforced concrete in open foundation and plinths or similar works complete as per drawings and MORD technical specification section 800, 900, 1200 1200, & clause 1203 and curing complete including the cost of form work and hauling of material within all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 11 | Providing and laying mechanically mixed and vibrated plain cement concrete grade M-15 (Fifteen) 1:2.5:5 (one cement: two point five sand: five graded crushed stone aggregate 40mm (Forty millimetre) nominal size) design mix with cement content not less than 275kg (two hundred seventy five kilogram) per cubic metre for plain/reinforced concrete in sub-structure and plinths or similar works complete as per drawings and MORD technical specifications section 800, 900, 1200 and 1600 and curing complete including the cost of form work as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 12 | Providing and laying mechanically mixed and vibrated plain cement concrete in foundation using grade M-20 (M-Twenty) 1:2:4 (one cement: two sand: four graded crushed stone aggregate 40mm (Forty millimetre) nominal size) design mix with cement content not less than 330kg (three hundred thirty kilogram) per cubic metre as per drawings and MORD technical section 800, 900, 1200 and 1600 and curing complete including the cost of form work including carriage of materials within all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 13 | Providing and laying mechanically mixed and vibrated plain cement concrete in sub-structure using grade M-20 (M-Twenty) 1:2:4 (one cement: two sand: four graded crushed stone aggregate 40mm (Forty millimetre) nominal size) design mix with cement content not less than 330kg (three hundred fifty kilogram) per cubic metre as per drawings and MORD technical section 800, 900, 1200 and 1600 and curing complete including the cost of form work including carriage of materials within all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 14 | Bedding for Pipe Type A (Concrete Cradle) Bedding: Laying concrete cradle bedding with M15 (fifteen) grade 1:2.5:5 nominal mix (one cement: two point five sand: five graded crushed stone aggregate 40 mm (Forty millimetre) nominal size) design mix with cement content not less than 275kg (two hundred seventy five kilogram) per cubic metre for Cement Concrete complete as per drawings and technical specification section 1100 & Clause 1101.5 (i) and curing complete including the cost of form work as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 15 | Providing and laying flooring with rubble stone in cement mortar 1:3 (one cement : three coarse sand) laid over cement concrete bedding complete as per drawing and technical specification section 1300 and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 16 | Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in Sub-structure complete as per drawing and MORD technical specifications section 1000 and 1200 including cutting, bending and binding in positionand as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. Taxes imposed by the Government but excluding GST. |
| 17 | Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in Super-structure complete as per drawing and MORD technical specifications section 1000 and 1400 including cutting, bending and binding in position and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 18 | Providing and laying mechanically mixed and vibrated reinforced cement concrete in sub-structure using grade M-20 (M-Twenty) 1:2:4 (one cement: two sand: four graded crushed stone aggregate 20mm (twenty millimetre) nominal size) design mix with cement content not less than 350kg (three hundred fifty kilogram) per cubic metre as per drawings and MORD technical section 800, 900, 1200 and 1600 and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work including carriage of materials within all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 19 | Providing and laying mechanically mixed and vibrated reinforced cement concrete in super-structure as per drawing and MORD technical specification section 800, 900, 1000, 1200, 1400 and 1600 using Reinforced Cement Concrete grade M-25 (M-Twenty five) 1:1.5:3 (one cement: one point five sand: three graded crushed stone aggregate 20mm (Twenty millimetre) nominal size) design mix with minimum cement contents not less than 400 Kg (Four hundred kilogram) per cubic metre and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab, etcetera including carriage of material within all leads, lifts and other incidental, as per the directions of the Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST |
| 20 | Providing and laying cement concrete wearing course M 30 (thirty) grade designed mix with cement content not less than 430 Kgs per cum (Four Hundred Thirty Kilogrammes per cubic metre) with 20 mm (Twenty millimetre) nominal size, including reinforcement and formwork complete as per drawing and MORD technical specifications section 800, 1400 and Clause 1404.2 and as per the direction of the Engineer-in-Charge including the cost of form work and carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 21 | Providing and laying mechanical mixed and vibrated R.C.C. (Reinforced Cement Concrete) M 25 (Twenty Five) grade design mix with minimum cement contents not less than 400 Kg (Four hundred kilogram) 1:1.5:3 (one cement: one point five sand: three graded crushed stone aggregate 20mm (Twenty millimetre) nominal size) approach slab including reinforcement and formwork complete as per drawing and technical specifications section 800, 1400 & clause 1404 and as per the direction of the Engineer-in-Charge including the cost of form work and carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 22 | Providing and laying (to level or slope) 900mm dia (Nine Hundred millimetres) diameter reinforced cement concrete heavy duty non pressure pipes IS (Indian Standard) Class NP-3 (Non pressure- three) for culverts on first class bedding of Granular material in single row including providing and fixing collar with cement mortar 1:2 (One cement : two sand) but excluding the cost of excavation, protection works, back filling, concrete bedding and masonry work in head walls and parapets as per drawing and MORD technical specifications section 1100 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 23 | Construction of R.C.C. (Reinforced cement concrete) railing of M 25 (Twenty Five) grade in cast-in-situ with 20 mm (Twenty millimetre) nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500 (One in Five hundred), centre-to-centre spacing between vertical posts not to exceed 2000 mm as per drawing and technical specifications Clauses 800, 900, 1400 and clause 1404.3 and as per the direction of the Engineer-in-Charge including the cost of form work and carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 24 | Drainage spouts with G.I. (Galvanized Iron) pipe 100 mm dia (one hundred millimetre diameter) & corrosion resistant structural steel grating complete as per drawing and MORD technical specifications Clause 1404.5 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 25 | Construction of unlined surface drains by mechanical means of average cross-sectional area 0. 40 sqm (zero point four zero square metre) in all kinds of soil & ordinary rock to specified lines, grades, levels and dimensions. Excavated material to be used in embankment as per MORD Technical Specification Clause 307 and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 26 | Providing and erecting W metal beam crash barrier comprising 3mm (three millimetre) thick corrugated sheet metal beam rail 70 cm (seventy centimetre) above road/ground level fixed on ISMC series Channel vertical part of 150 mmx75 mmx 5 mm (one hundred fifty millimetre into seventy five millimetre into five millimetre) special 2. 00 (two point zero zero) metre centre to centre 1. 80 (one point eight zero) metre high 1. 10 (one point one zero) metre below ground road level all steel parts and filaments to be galvanized by hot dip process, a fitting to confirm to IS 1367 and IS-1364 metal beam rail to be fixed on the vertical post with a space of channel section 150 mmx75 mmx5 mm (one hundred fifty millimetre into seventy five millimetre into five millimetre) 330mm (three hundred thirty millimetre) long complete as per MORTH Specification section 800 and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 27 | Providing and laying of boulder apron laid in wire crates with 4 mm (four millimetre) dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm (one hundred millimetre into one hundred millimetre) mesh (woven diagonally) including 10% (Ten percent) extra for laps and joints laid with stone boulders weighing not less than 40 kg (forty kilogram) each as per drawing and MORD technical specifications section 1300 as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 28 | Preparation of sub grade by dressing to camber (Earth work for the cutting involved for sub-grade to be paid for separately) depending upon the classification of soil completed as per HP.PWD specifications and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 29 | Consolidation of sub grade with road roller including making good the undulation etc. with earth or quarry soil etc. and rerolling the sub-grade completed as per HP.PWD specifications complete and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 30 | Stone soling properly hand-packed filling interstices with Kharanja stone and consolidating with power road roller to the requested gradient and comber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification 100 mm (One hundred millimetre) spread thickness (finished work including materials and labour) and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 31 | Providing and fixing of typical NABARD informatory sign board with logo as per MORD specification and drawing. Three MS plates of 1. 6 mm (one point six millimetre) thick top and middle plate duly welded with MS flat iron 25mmx5mm (twenty five millimetres x five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimetres into twenty five millimetres into five millimetres). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. (Two Nos.) 75mmx75mm (seventy five millimetre x seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1: 2.5: 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm (Forty millimetres) grade blocks of 450mmx450mmx600mm (four hundred fifty millimetres into four hundred fifty millimetres x six hundred millimetres), 600mm (six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimetres x forty seven millimetres) of 12 SWG (Twelve Standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and MORD technical specifications section 1700 and Annexure 1700. 1 as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 32 | Providing and fixing 5th (fifth) Kilometre stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC: 8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 33 | Providing and fixing Ordinary Kilometre Stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC: 8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 34 | Providing and fixing 200m (two hundred metre) Stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC: 26 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 35 | Providing and fixing of Semi-reflective cautionary, mandatory and informatory sign board 600 mm (six hundred millimetre) equilateral triangle as per IRC:67 made of 1.5 mm (one point five millimetre) thick MS sheet duly stove enamelled paint in white colour in front and grey colour on back with red reflective border of 65 mm (sixty five millimetre) width and required letters and figures with reflective tape engineering grade as per section 1700 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47mm of 12 SWG (forty seven into forty seven millimetre of twelve Standard Wire Gauge) sheet square tube firmly fixed to the ground by mean of properly designed foundation with M-15 grade (M- fifteen grade) cement concrete 450mm x 450 mm x 600 mm (four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm (six hundred millimetre) below ground level as per drawings and MORD Technical Specification section 1700 including painting angle iron post with primer and two post of Epoxy paint as per specification and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 36 | Providing and erecting direction and place identifications signs up to 0.9 sqm (Zero point Nine square metre) of semi reflective sign boards as per IRC:67 made of 2 mm (Two millimetre) thick M.S. Sheet duly stove enamelled paint in white colour in front and grey colour on back with red reflective border of 70 mm (Seventy millimetre) width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour. Supported and welded on 47 mm x 47mm (Forty Seven millimetre into Forty Seven millimetre) of 12 SWG (Twelve Standard Wire Gauge) Square tube of 3050 mm (Three Thousand Fifty millimetre) height duly strengthened by 25 mm x 5 mm (Twenty Five millimetre into Five millimetre) MS (Mild steel) flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 (Fifteen) grade cement concrete 450 mm x 450 mm x 600 mm (Four Hundred Fifty millimetre into Four Hundred Fifty millimetre into Six Hundred millimetre), 600 mm (Six Hundred millimetre) below ground level as per approved drawing and Technical Specification Clause 1701 and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 37 | Providing and erecting direction and place identification signs more than 0.90 sqm (Zero point Nine Zero square metre) of semi reflective sign boards as per IRC:67 made of 2 mm (Two millimetre) thick M.S. Sheet duly stove enamelled paint white colour in front and grey colour on back with reflective border of 70 mm (Seventy millimetre) width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm (Forty Seven millimetre into Forty Seven millimetre) of 12 SWG (Twelve Standard Wire Gauge) square tube of 3050 mm (Three Thousand Fifty millimetre) height duly strengthened by 25 mm x 5 mm (Twenty Five millimetre into Five millimetre) MS (Mild steel) flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 (Fifteen) grade cement concrete 450 mm x 450 mm x 600 mm (Four Hundred Fifty millimetre into Forty Hundred Fifty millimetre into Six Hundred millimetre), 600 mm (Six Hundred millimetre) below ground level as per approved drawing and Technical Specification Clause 1701 and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 38 | Planting rooted plants (Burans, Vaan etc) on road side slopes, including splitting into separate viable rhizome sections, trimming roots, preparing lines, digging planting hole to a size 60 cm dia and 60 cm depth with suitable instruments depending on nature of soil planting rhizomes at the spacing specified, and subsequent watering (if necessary) and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 39 | Bamboo tree guard 1.80 mtr. Height with 30 cm dia with 4 Nos. verticals strips (length 1.80 mtr. Breadth 30 mm thickness 5mm) further weaving with different smaller size of verticals and circular strips. The weaved portion should be 125 cm having 3 rings at the top, bottom and middle portion. The first ring should be 55 cm above the 4 thick vertical strips i/c strengthening with barbed wire and as per the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 40 | Bridge Work |
| 41 | Earth work in excavation of foundation of bridge for structures in all depths as per drawing and MoRTH technical specification section 300 and clause 304 including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal in all leads and lifts including dressing of sides and bottom and back filling in trenches with excavated suitable materials. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion damage to hill side water pollution etc. and to protect stability of hill side rock shall be excavated with chiselling and wedging out rock (where blasting is prohibited). All earth work in cutting/excavation including rock excavation shall be carried out true to lines, grades, side slopes, width, camber super elevation and levels as shown on the drawings or as directed by the Engineer-in-Charge hauling and stacking of materials useful for construction at suitable sites and safe disposal of unsuitable cut materials in specified manner filling of unevenness blind age and finishing of the road to specified dimension or as directed by the Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 42 | Providing and laying mechanically mixed and vibrated plain cement concrete M-10 (Ten) grade 1:3:6 nominal mix (One cement: Three sand: Six graded crushed stone aggregate 40 (Forty millimetre) nominal size) in foundation including form works in any height complete as per drawing and MoRTH technical specifications Section 1500, 1700 and 2200 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 43 | Providing and laying mechanically mixed and vibrated reinforced cement concrete Grade M-30 (Thirty) (M-Twenty five) design mix with cement content not less than 407 kg per cum (Four hundred Seven kilogramme per cubic metre) with 20mm (Twenty millimetre) nominal size) design mix with minimum cement contents not less than 410 Kg (Four hundred Ten kilogram) per cubic metre in sub structure including form works but excluding reinforcement in any height complete as per drawing and MoRTH technical specifications Section 1500, 1700 and 2200 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 44 | Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and technical specifications as per MoRTH Section 1600 and 2200 including cutting, bending binding and straightening in position and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 45 | Providing and laying of Filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in clause 2504.2.2 of MoRTH specifications to a thickness of not less than 600 mm (Six hundred millimetre) with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specification clause 710.1.4.of IRC:78 & 2504.2 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 46 | Providing weep hole in brick masonry/plain/reinforced concrete abutment, wing wall, return wall with 100mm (One hundred millimetre) dia. PVC/AC pipe, extending through the full width of the structures with slope of 1V:20H (One vertical: Twenty horizontal) towards draining face complete as per drawing and technical specifications and carriage of material within all leads, lifts/depths and other incidentals as per MoRTH clause 2706 Section 2200 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 47 | Supplying, fitting and fixing in position true to line and level cast steel rocker bearing conforming to IRC: 83 (Pt.-1) section IX (Eleven) and clause 2003 of MoRTH specifications complete including all accessories as per drawing and Technical Specifications section 2000, 1000 and 2200 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 48 | Supplying, fitting and fixing in position true to line and level forged steel roller bearing conforming to IRC: 83 (Pt.-1) section IX and clause 2003 of MoRTH specifications complete including all accessories as per drawing and Technical Specifications section 2000, 1000 and 2200 and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 49 | Furnishing and Placing Reinforced/ Prestressed cement concrete grade M-35 (Thirty five) grade design mix with cement contents not less than 422 kg per cum (Four Hundred Twenty Two kilogram per cubic metre) with 20 mm (Twenty millimetre) nominal size graded crushed stone aggregate in superstructure including form works but excluding reinforcement in any height using concrete mixer as per drawing and MoRTH Technical Specification Section 1500, 1600, 1700 & 2300 and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 50 | Supplying, fitting and placing HYSD bar reinforcement (Fe-415) in superstructure complete as per drawing and MoRTH Technical Specification section 1600 & 2300 including cutting, bending and binding in position and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 51 | Providing and laying plain cement concrete (PCC) M15 (Fifteen) 1:2.5:5 (One cement: Two point Five sand: Five graded crushed stone aggregate 40mm (Forty millimetre) nominal size) Grade levelling course below approach slab excluding formwork complete as per drawing and Technical specification as per MoRTH Section 1500, 1600, 1700 and clause 2704 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 52 | Providing and laying mechanically nixed and vibrated concrete for reinforced cement concrete grade M-30 (thirty) in approach slab including reinforcement and formwork complete as per drawing and Technical specifications as per MoRTH Section 1500, 1600, 1700 and clause 2704 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 53 | Providing and laying mechanically mixed and vibrated cement concrete wearing coat M-30 (thirty) grade designed mix with cement content not less than 407 kg per cum (Four Hundred Seven Kilogramme per cubic metre) with 20 mm (Twenty millimetre) nominal size including reinforcement and form work complete as per drawing and Technical Specifications as per MoRTH clause 2702 and as per the direction of the Engineer-in-Charge including the cost of form work and carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 54 | Construction of RCC railing of M30 (thirty) grade in-situ with 20 mm (twenty millimetre) nominal size aggregate, true to line and grade, tolerance of vertical RCC (Reinforced Cement Concrete) post not to exceed 1 in 500 (One in Five hundred), centre to centre spacing between vertical post not to exceed 2000 mm (Two thousand millimetre), leaving adequate space between vertical post for expansion, including reinforcement and form work complete as per approved drawings and technical specifications as per MoRTH clause 2703 and section 1500, 1600 and 1700 and as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 55 | Providing drainage Spouts with G.I. (Galvanized Iron) pipe 100 mm dia (one hundred millimetre diameter), G.I. (Galvanized Iron) bolt 10 mm dia (Ten millimetre diameter) & corrosion resistant structural steel grating complete as per drawing and Technical specifications as per MoRTH clause 2705 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 56 | Providing and laying of a strip seal expansion joint catering to maximum horizontal movement up to 70 mm, (Seventy millimetre) complete as per approved drawings and standard specifications to be installed by the manufacturer/supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation complete as per MoRTH clause 2607 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. the Engineer-in-Charge. |
| 57 | Providing and fixing in position 20 mm (Twenty millimetre) thick pre-moulded joint filler in expansion joint for fixed ends of simply supported spans not exceeding 10 m (Ten metre) to cater for a horizontal movement up to 20 mm (Twenty millimetre), covered with sealant complete as per drawing and technical specifications section 2600 & 2604 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. Please Enable Macros to View BoQ information |
