|
| 1 | Dismantling of Mild steel rusted valley gutter, eave gutter, etc of any discription & removing to store or as directed by EIC. |
| 2 | Dismantling plain or corrugated CGI sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all & removing to store or as directed by EIC. |
| 3 | S&F mild steel valley gutter 3.00mm/3.15mm thick including bending, turning up to required shape & size, welded attachment with all necessary items which is required at the site. (Fe410-Wgde E-250 Quality A ).(Make: TATA, SAIL, JSW) |
| 4 | M&L preperation of new surfaces of any description, over 10cm in width or girth, not otherwise described & applying one coat of red oxide primer and two coat of synthetic enamel paint on iron surface.(Make: Asian-Apcolite, Berger, Nerolac) |
| 5 | S&F of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws and silica sealing compound, profile, shape & size as per site requieremnt. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating. (Make: TATA, SAIL, JSW) |
| 6 | S & F of pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick having tensile strength of 550 Mpa as in Ridge covering, Frill, Facia, etc fixed with self tapping screws, shape & size as per site requieremnt. It shall be coated with hot dip alloy of 55% Aluminium 43.5% Zinc 1.5% Silicon and finished with resin coat on both surfaces @ 150 gm/sqm of coating. (Make: TATA, SAIL, JSW) |
| 7 | S&F of 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, bent to a curve (of any radius) fixed with grade of zinc coating 275. (fixed with L-type or J-type or cranked hook bolts in lieu of screws) Make: TATA, JINDAL, Kamdhenu |
| 8 | S&F of 2.0mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc. |
| 9 | M&L of rough cast wired glass, 6.4mm thick and glazing with oil putty in square exc 0.5 sq. m but n exc 0.75 sq.mtr in each pane. |
| 10 | S&F of Flue pipe /down take pipe / Rain water pipe etc. with mild steel sheet black of 150 mm dia with 2.0mm thick sheet.all as directed by EIC. |
| 11 | S&F of Flue pipe /down take pipe / Rain water pipe etc. with mild steel sheet black of 250 mm dia with 2.0mm thick sheet.all as directed by EIC. |
| 12 | S&F of PVC(SWR) Pipes of dia 150 mm with all acceroies like 'T', Band, Socket, etc, complete as per site requirement. Make: Kishan, Supreme, Astral, Finolax. |
| 13 | S&F of PVC(SWR) Pipes of dia 200 mm with all acceroies like 'T', Band, Socket, etc, complete as per site requirement. Make: Kishan, Supreme, Astral, Finolax. |
| 14 | S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing boltsposts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work . |
| 15 | S&F MS rolled steel section for roof trusses purlins, rafter etc framing (Beam, tee, angle, channel or flat sections). (Fe-410-Wgde-250) Quality-A) |
| 16 | Supply and installation of windy ventilator double bearing (Turbo Ventilator) with FRP/Polycarbonate base and Rain Water proof with spinning speed of ventilator wing should work in less than one kilometer per hour and may stand in storm exceeding 125 km per hour, wearing protected against fume and smoke, material of ventilator shall be stainless steel blade of thickness 5mm, throat diameter of ventilator shall be 60cm and outer dia of ventilator 75 cm and area covered by ventilator is approx 50 sqm, complete as decided and approved by EIC. Please Enable Macros to View BoQ information |