|
| 1 | Rates are exclusive of GST |
| 2 | Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. |
| 3 | Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC. |
| 4 | Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW |
| 5 | Supplying and erecting mains with 1x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW |
| 6 | Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV |
| 7 | Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 8 | Supplying & erecting three phase, 415V, street light control panel up to the max load of 6kW, TPN MCB 40A, powder coated CRCA 14 SWG sheet, outdoor type, having IP54,IK10 protection, suitable rating contactor, 24 hrs. astronomical time switch with minimum 5 years battery back up, auto/manual selector switch, ON/OFF push buttons, indicator lamps, control wiring, metering device, etc. for automatic operation, with overcurrent, short circuit, earth fault protection on provided iron frame / CC foundation. |
| 9 | Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. |
| 10 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL |
| 11 | Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. |
| 12 | Supply of DMX Controller System with Standalone interfaces. Controller should deliver 2*512DMX channels, the controller should have future upgradation provision up to 4 DMX universe Port. the controller should have new Nicolaudie Stand Alone engine (NSA) offering some great possibilities (multi-zone, extended triggers, 16-bit channels management...). the controller should offer multiple possibilities to trigger your lighting scenes: time/date, input ports, TCP/UDP commands. Should have Intuitive backlit keyboard with 10 presets. PC DMX IN triggers:Yes, Standalone DMX IN triggers: External triggers: 10 buttons for direct access,2 buttons to change scene,+ 1 button to change zone. 16 dry contact trigger ports via 20-Pin IDC Socket. Internal calendar: Yes, Backup of the internal clock: Yes, 3weeks without power, Memory card: Yes microSD card, 32GB max, Input power voltage: 5-5.5V DC 0.6A with power adaopter working on AC power supply,. via USB(USB power supply included), Trigger lighting scenes using calendar triggers and conditional rules with New Stand Alone engine, using contact ports, RS232 or over Ethernet. Stand Alone mode with 99 scenes across 5 zones. Buttons: iPhone/iPad/Android remote and programming apps. Temperature: 0 to +50 C°, DMX Compatibility: 8 and 16 bit DMX fixtures, System Compatibility: Windows XP, Vista, 7, 8, 8.1, 10, MAC OS X. Make: Nicolaudie/Pharos/Osram ECUE/Philips iColor (10.6 and +), Linux.: Make: Nicolaudie: SLESA-U11 |
| 13 | Supply, installation, testing and commissioning of DMX Splitter cum Booster ,Input Power- 100 to 240 VAC, auto-ranging, 50/60 Hz.,Housing rugged alluminium, Operation Temperature -17ºC ~ +55ºC (0ºF ~ 131ºF) , 5/6 output ports with 3/5-pin terminal sockets , each port should be optically isolated , Protection Rating IP20 including connection complete as required. Make: Pioneer/Briteq/Swisson |
| 14 | Installation Testing and commision of above items, including all accessories required for successfull operation of system, like Lighting Panel, Power & DMX/CAT-6 Cables Junction Boxes/connectors etc. Progarmming and testing of controllers. 1. Addressing, Patching and Programming DMX Light Fixtures 2. Creating many number of sequences as per client's requirement. 3. Training of the site technicians. |
| 15 | Supplying, Installing, Testing & Commissioning Underwater Projector Light, NHL-N-14, 9-14W, LED, 3000k, IP 68. The housing made of completely made of Stain Steel. Protection screen in white tempered glass with high impact resistance . Precise structure and multi-protection silicon rubber seal guarantees the fixture IP68 rated. Height – 167mm, Dia.-127mm Power LED Module with high efficacy LED's, on Printed Circuit Board with metal core plate. Estimated LED Lifetime is L70-50,000 hours minimum. LM80 report from LED Manufacturer should be submitted. Minimum Light fixture Lumen output is 500 Lumens. Sample Should be submitted for concerned engineer incharge for approval of light fixture. |
| 16 | Supply of LED ground Burial Light made up from High Pressure Die Cast Aluminium with Stainless Steel Frame & Screws Engineered plastic housing , Glass/Diffusor -Clear Toughened Glass;colour Graphite Grey, Ingress Protection: Optical Compartment IP67, Impact Resistance IK10; Extra-clear tempered glass, 4/5mm thick Power Supply Power Efficiency ≥80%; Power Factor ≥0.90;Surge protection 4KV; Operating Input voltage Range 140 to 270V; ATHD ≤15%; High performance LED technology- High Bright LED-Osram/Cree/Lumiled; electrical Class I wattage 18W ± 10%; Ambient Temperature Range--10 to +50°C Average Ambient Temperature +25°C with wind effect;LED CCT 3000K/ 4000K/ 5700K, LED CRI Initial - ≥70/≥80 (White LED) BEAM ANGLE- 10°/15°/25°/45°/60° LED Lifetime@Ta 25°C#50000hrs-L70; Electrical Safety Class- lll, Rated Voltage/Frequency- 24 V DC; System Power Consumption Initial- 18W; Should have provision of tilting, Control ON-OFF/DMX512. The luminaire should be having a warranty for a period of 2 years against any manufacturing defects. The Manufacturer should have valid ISO 9001:2015 from TUV Rhineland & CE certification. The manufacturer should have internal testing equipment’s especially 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. The manufacturer shall submit the LM 80 report for LED used in the fixtures. |
| 17 | Supply of Spot Light made of Aluminium body with High Pressure Die-Cast Thermal Management with aesthetically designed Fins for longer life of the LEDs and the IP65 optical compartment. The back cover should also be High Pressure Die Cast Aluminium. The system AC wattage of the luminaire shall be 12~15W (±10%) WITH COB (MAKEBRIDGELUX/ LUMILED/TYF) For better light output with Aluminium reflector, Color temperature (CCT) of 3000K, colour rendering index CRI >/= 80 and residual flux of 70% (L70) @ 50,000 hours at Ta of 25°C. The luminaire should be deigned to operate at any voltage from 140V to 280V, with Power Factor ≥ 0.95 and shall be provided with optional built in Over Voltage and Under Voltage protection and internal surge protection of 4kV, electrical Class I. Overall outer dimensions of luminaire shall be 215mmL (±3%) x 100mmW (±3%) and 240mmH (±3%) Height and the shape shall be as per the shown image. The luminaire should be having a warranty for a period of 2 years against any manufacturing defects. The Manufacturer should have valid ISO 9001:2015. The manufacturer should have internal testing equipment’s especial 2m Integrating Sphere, IPX6, IK10, Humidity Chamber. |
| 18 | Supply of high quality RGBW Floodlight projector having precies beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of pressure die-cast Aluminium with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 35°C. The lens shall be made of anti-aging & anti UV-PMMA material and able to minimize hot spots & fringing in color mixing to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. Luminaire should have DMX-512 control protocol and should have inbuilt DMX decoder chip. The luminaire shall have system wattage 70~ 75W and system lumen output of not less than 2890 lumens, Beam angle should be narrow : 15/25 Degree/As per site condition, The fixture shall have an integral driver with input voltage for 220-240 VAC, 50/60Hz, power factor > 0.90 complying to BIS standard \\"IS 10322 ,Color Temperature : RGBW, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. Luminaire should have pre wired integral male/female waterproof connectors as per IS standard for DMX Loop In/out facility. |
| 19 | Supply of high quality RGBW Linear wall washer having precise beam angle as per design or site requirement suitable for façade lighting applications. Housing to be made of extruded Aluminium alloy with excellent heat management system to ensure proper heat dissipation and thermal stability of the luminaire. The luminaire shall have electrostatically applied polyester powder coating finish. Luminaire shall be suitable to operate in a temperature range of -10°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 35°C. The lens shall be made of anti-aging & anti UV-PMMA material and able to minimize hot spots & fringing in color mixing to insure proper light distribution. Suitable for outdoor weather proof conditions having IP66 ingress protection. Transparent toughened glass having impact resistance protection of IK08. Luminaire should have DMX-512 control protocol and should have inbuilt DMX decoder chip. The luminaire shall have system wattage 24W and system lumen output of not less than 1010 lumens, Beam angle should be narrow : 10x60 /15x45 Degree/As per site condition, The fixture shall have input voltage for 24V DC, external high efficiency driver having power factor >0.90, Surge protection 4KV and other protections including OCP, OVP, SCP, OTP shall be provided. Luminaire complying to BIS standard \\"IS 10322\\" ,Color Temperature : RGBW, Operating Temperature : -10°C to +50°C, Operating Humidity : 10%-90%, LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia, Bridgelux to insure higher lumen output and brightness with SMD LED chips. Luminaire should have pre wired integral male/female waterproof connectors as per IS standard for DMX Loop In/out facility. |
| 20 | Supply, of IP67 Power Supply 24V output. Power consumption- 200W. The Driver should be of same make as the fixtures and should be BIS approved. All necessary certificates should be provided at time of Tender submission, which is mandatory.The product should have a minimum 5-year warranty. |
| 21 | Supply, of DMX Special Cable (single pair) having one 22AWG pair stranded (7x30) tinned copper conductors, Datalene (FHDPE) insulation, twisted pairs, overall Beldfoil shield (100% coverage) plus tinned copper braid, PVC jacketCable. Prefered make Beldon or equivalent as approved by Consultant & Engineer in Charge. |
| 22 | Supply of IP68 T Connector 3 PIN suitable 2.5sqmm flexible cable as per IS/IEC 60529: 2001 (IP68). The product must be Tested in NABL LAB with instruments used are maintained in accordance of IS/ISO /IEC 17025. NABL certificates should be provided at time of Tender submission. |
| 23 | Supply of IP68 T Connector 4 PIN suitable 2.5sqmm flexible cable as per IS/IEC 60529: 2001 (IP68). The product must be Tested in NABL LAB with instruments used are maintained in accordance of IS/ISO/IEC 17025. NABL certificates should be provided at time of Tender submission. |
| 24 | Supply of IP68 T Connector 5 PIN suitable 2.5sqmm flexible cable as per IS/IEC 60529: 2001 (IP68). The product must be Tested in NABL LAB with instruments used are maintained in accordance of IS/ISO/IEC 17025. NABL certificates should be provided at time of Tender submission. |
| 25 | SITC of LED IK10 30W Luminaire & decorative ornamental 3 meter height Pole (Above ground level till Luminaire Bottom), made up of two sections ,bottom section shall be made up of 114 mm diameter & 3mm thickness, GI pipe of 1000 mm height, top section of 76 OD diameter & 3mm thickness GI Plain / Ribbed pipe, 2000 mm height and base plate shall be made up of MS plate .The pole is designed to mount post top or post top side mounting fixture with 76 ID pipe ,the pipe shall be made by ERW pipes confirming to IS 1161 /IS 1239 All plates confirming to A36/A572-50 IS: 2062 or equivalent, the pole shall be PU paint of graphite grey color, shall have 3 layer coating of Minimum DFT level is 60 Microns. 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint, a suitable service window shall be provided in the base of pole to allow access to electrical Connections and terminations, Pole unit can be grouted using 4 nos. anchor J-bolts of size M16 x 250 mm long confirming to EN 8 Gr. Pole should be from same company of decorative luminaire for proper installation at site. Decorative pole to be Supplied with LED Decorative IK10 Luminaire, Supply of BIS Certified (as per IS10322 Part 5/ Sec 3) 30W LED Post top Luminaire. The Heat Sink of Post top should be made of Pressure Die Cast Aluminum (Grade – ADC 12) in single pc (Not in extruded fins aluminum housing or module form or spun Housing). Heat sink should fin design for better thermal management. The Optical cover should be made of Clear polycarbonate (Virgin PC), product should be IK10 rating & IP66 with complete optical part of product. To ensure any chance of Ingress breach, the fully sealed LED compartment remains intact at the time of maintenance or service of LED driver or SPD. Product should be painted with UV protected pure polyester powder coated Grey colour after phosphochromate treatment. The lower base of the Light Fixture is also made up of Pressure Die Cast Aluminum (Grade – ADC 12) in single pc. Product should be equipped with LED with make Osram, Cree, Nichia, Color Rendering Index (CRI) >70 and L70 rated lifetime of 50,000 hours. System Lumen Efficacy of 110 Lumens/watt in 4000K with symmetrical light distribution. Mounting on pole with outer Dia 60 mm. Electrical Class I, System Power 30W, rated voltage 240VAC, Power Factor ≥ 0.95, offered with BIS certified potted driver having Internal surge protection of 4/4kV (in both Common & Differential Modes), Led Driver efficiency should be > 85% and an additional/external Surge Protection Device (SPD) of 10/10kV (in both Common & Differential Modes). Product and Led driver should be connected with detachable male -female connector. The product should have a minimum 5-year warranty. Product must be comply with IEC 62262: 2002, IS/IEC 60529, IS 10322 (Part 5/ Sec 5):2013+A1:2018 in conjunction with IS 10322(Part-1):2014 & LM 79/80. Please Enable Macros to View BoQ information |
