|
| 1 | Schedule 'A' |
| 2 | Material and labour for periodical cleaning of underground sump/Over Head tank by bailing out the remaining water after pumping by arranging re-watering pumps or by manual and wash the walls & bottom surface by high pressure spray of approximating 195 PSI with rotary water jet pumps and removing the sludge and foreign matters complete by and socking out the fixing with high pressure wet vacuum pumps scrubbing the wall and cleaning the entire sump including disinfectioning the tanks with spray of chemical approach by concerned authorities and painting two coat of white lime wash complete all as directed by the Engineer-in-Charge of following capacity :- |
| 3 | 4.0 Lakh ltr capacity |
| 4 | Upto 2.0 Lakh ltr capacity |
| 5 | M & L for periodical servicing of electric driven pumpsets disconnecting the electric connection from motor terminal box including insulating the ends of the cable, taking out the pump set from base after opening nuts/bolts, transporting from site to workshop, dismantling pump, removing worn out impeller, ball bearing, gaskets, assembling the pump with replacement of minor parts as required such as pulley key, gland packing rope, greasing etc., transporting back to site and fixing on the existing foundation, connecting the electric connection of motor and testing complete to entire satisfaction of Engr-in-charge for the following capacity. (Note :- Major spare parts shall be measured and paid separately, minor spares deemed to be in rate quoted, spares like pump shaft, impeller and bearing only will be measured and paid separately under relevant items ) |
| 6 | Centrifugal pump set of capacity 30 HP (any make) |
| 7 | Centrifugal pump set of capacity 12.5/10 HP (any make) |
| 8 | Centrifugal/Submersible pump set of capacity 7.5/5 HP (any make) |
| 9 | Centrifugal/Submersible pump set of capacity 2/3 HP (any make) |
| 10 | Supply only Bearing for Motor or Pump of capacity 30 hp complete all as specified and directed by Engr-in-charge. Make : SKF/NBC/TATA Note : - Labour charnges are included in item No. 2 above. |
| 11 | Supply only Bearing for Motor or pump of capacity 12.5/10 hp complete all as specified and directed by Engr-in-charge. Make : SKF/NBC/TATA Note : - Labour charnges are included in item No. 2 above. |
| 12 | Supply only Gun metal bush suitable for motor capacity 12/15 hp complete all as specified and directed by Engr-in-charge . Note : - Labour charnges are included in item No. 2 above. |
| 13 | Supply only Gun metal bush suitable for motor or pump of capacity 30 hp complete all as specified and directed by Engr-in-charge .Note : - Labour charnges are included in item No. 2 above. |
| 14 | Supply only power transmitting shaft and coupler for Motor and pumpsets of capacity 30 hp complete all as specified and directed by Engr-in-charge |
| 15 | Supply only power transmitting shaft and coupler for Motor and pumpsets of capacity 12.5/10 hp complete all as specified and directed by Engr-in-charge |
| 16 | Material and labour for rewinding the electric motor of capacity 5 HP to 7.5 HP capacity, disconnecting the electric connection of motors, earth connections, decoupling motor and pump, removing foundation nuts/bolts and removing the motors from its existing position to workshop (Note : following work are to be deemed in rate quoted). |
| 17 | Removing the split case/body cover of motor, separate stator/rotor and cutting the complete burnt/defective copper winding. |
| 18 | Cleaning the stator body complete by rubbing sand paper remove all carbons. |
| 19 | Insert insulating materials such as insulating paper sleeves. |
| 20 | Rewinding the stator with existing size of super enameled copper winding, varnishing and heating up at desired temp. For achieve the particular Ohm resistance. |
| 21 | Clean the rotor and assembling in motor. |
| 22 | Connection/coupling the motor with pump, connect all electric/earth connection foundation nuts/bolts at its original position and testing on load complete all as specified and directed. |
| 23 | All as per item No. 9 above but 12.5/10 HP motor. |
| 24 | All as per item No. 9 above but 30.0 HP motor. |
| 25 | Supply and laying in replacement or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed 4 sq. mm nominal cross section, 3 core in service connections all as specified and directed by Enge-in charge. |
| 26 | M & L for providing water tapping connections from existing line of size 80 mm to 200 mm DI/GI pipe line including taking up old connections, including required tapping ring and clamps of 80 mm to 200 mm size & suitable length pipeline all as specified and directed by Enge-in charge. |
| 27 | M&L for Repair to Chlorination dosing plant consist of dosing pumpsets induction motor of 220 volts ,single phase, 120 Watt and 960 RMP - 02 Nos , stirrer assembly including replacement of striring rod,blade, Storage drum of capacity 100 Ltr - 01 Nos & Mixing Drum of capacity 500 Ltr - 01 Nos, injection nozzle of suitble size, |
| 28 | S & F in repair rubber coupler between Motor and Pumpset shaft all inclusive of dismentalling shaft ,checking level motor and pump shaft by level meter before fitting coupler for 7.5 HP to 30 HP capacity centrifugal motor Pumpsets. |
| 29 | M& L for repair work of main DI/GI/UPVC pipe line of 25 mm dia to 200 mm dia size by cutting of pipe, Threading of GI pipe, jointing kit, sockets, unions GI/UPVC of suitable size, clamps etc. The job included cutting of pipe line and provision of required lengh pipe line (upto 1.00 mtr) as required and jointing accessories etc. |
| 30 | Supply and fixing in repair DOL starter suitable for 1 hp to 2 HP motor complete with sheet-steel enclosure complete all as directed by the Engineer-in-Charge Make : L & T or equivalent. |
| 31 | Supply and fixing in repair DOL starter suitable for 3 hp to 5 HP motor complete with sheet-steel enclosure complete all as directed by the Engineer-in-Charge Make : L & T or equivalent. |
| 32 | Supply and fixing in repairs star-delta starter suitable for 30 HP motor type MK-1 complete with sheet-steel enclosure, complete all as directed by the Engineer-in-Charge Make : L & T or equivalent. |
| 33 | Supply and fixing in repairs star-delta starter suitable for 10 HP to 12.5 HP motor type MK-1 complete with sheet-steel enclosure, complete all as directed by the Engineer-in-Charge Make : L & T or equivalent. |
| 34 | Taking down old GI tubing 80/50/40/25 mm bore medium grade from trenches/wall/floor etc including making good the disturbed surfaces complete all as specified and directed by Engineer-in-Charge. |
| 35 | Supply and fix GI tubes medium grade complete with all fittings (misc fitting required on site like; union, tee, bend, elbow, reducer, socket deemed to be included in rate) tobe fixed on wall and ceilings or laid in floors/trenches complete of following bore of pipes:- GI tubes medium grade 80 mm dia |
| 36 | All as per item No 22.00 above but GI tubes medium grade 50 mm dia. |
| 37 | All as per item No 22.00 above but GI tubes medium grade 40 mm dia. |
| 38 | All as per item No 22.00 above but GI tubes medium grade 25 mm dia. |
| 39 | Taking down unserviceable gun metal globe or gate valveof any size from existing location. |
| 40 | S & F gate valve, with iron/UPVC wheel head screwed both ends for iron/ UPVC pipe of 50 mm bore incl provn of union nipples sockets etc. |
| 41 | All as per item No.27 above but of 40 mm bore |
| 42 | All as per item No.27 above but of 25 mm bore |
| 43 | All as per item No.27 above but of 20 mm bore |
| 44 | Supply & Fixed in replacement CI foot valve heavy duty 80 mm dia brass with all accessories complete all as specified and directed by Engineer-in-Charge note: Clamps of required size and nut bolts deemed to be included in rate. |
| 45 | All as per item No.31 above but 150/100 mm dia. |
| 46 | Material and labour for servicing of the pressure pump including replacement of pressure switch, of given capacity of tarrace single phase 230 volts capacity, disconnecting the electric connection of motors, and removing the motors from its existing position and sending to workshop for repairs/rewinding complete and refixing the same after repairs complete all as specified and directed by Engr-in-charge. |
| 47 | M&L for Servicing of Submersible pump set 3 phase 2/3 HP alongwith dismantaling of HDPE/GI pipe from UG Sump and refixing the same by replacing the wornout winding and rewinding with same size gauge, super enameled copper wire, warnishing, greasing, bearing, nuts, bolts and gland packing, greasing and testing the pump set complete all as directed by Eng-in-charge. |
| 48 | M & L servicing and repairing of cast iron sluice valve 200 mm dia complete with flanged end, gaskets, packing, replacement of threaded shaft with nut assemble and metal diapharm , rotatating wheel , nut and bolts, painting two coat of black colour as per IS 780 including all joints with rubber gasket, bolts, and nuts washer complete all as specified of sizes. |
| 49 | All as per item No.35 above but 150 mm dia. |
| 50 | All as per item No.35 above but 100 mm dia. |
| 51 | All as per item No.35 above but 80 mm dia. |
| 52 | Supply and fixing in repair MCCB, AC 415 V, 50 HZ, fixed type, capacity 200 Amps, 4 Pole, 36 KA, suitable to be fixed in LT panel complete all as specified and directed Make: L&T or eqivalent |
| 53 | All as per item No. 39 above but of capaqcity 160 amps 36 KA . Make: L&T or eqivalent |
| 54 | All as per item No. 39 above but of capaqcity 125 amps 16 KA . Make: L&T or eqivalent |
| 55 | All as per item No. 39 above but of capaqcity 25 Amps to 100 Amp16 KA . Make: L&T or eqivalent |
| 56 | Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth getting out for the laying of pipe all as directed in Hard/dense soil complete all as specified and directed. |
| 57 | Returning filling in including spreading, levelling, watering and well ramming in layers not exc. 25 cm in thick all as specified and directed. |
| 58 | Removing excavated material to a distance not exc 50 mtr and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified by the Engineer-in-charge. |
| 59 | Supply and laying in repair CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete with all fittings (like; union, tee, bend, elbow, reducer, socket) tobe fixed on wall and ceilings or laid in floors/trenches complete of 50 mm dia all as specified and directed by EIC. |
| 60 | All as per item No. 46 above but of size 40 mm dia |
| 61 | M & L repairing of non return valve 150 mm dia complete with flanged end, gaskets, packing, replacement of threaded shaft with nut assemble and metal diapharm , rotatating wheel , nut and bolts, painting two coat of black colour as per IS 780 including all joints with rubber gasket, bolts, and nuts washer complete all as specified of sizes |
| 62 | M & L repairing of non return valve 100 mm dia complete with flanged end, gaskets, packing, replacement of threaded shaft with nut assemble and metal diapharm , rotatating wheel , nut and bolts, painting two coat of black colour as per IS 780 including all joints with rubber gasket, bolts, and nuts washer complete all as specified of sizes |
| 63 | M & L porbandar stone masonary valve chamber of size 0.90 m x 0.90 m X 0.75 m (internal size) and cover including earth work complete all as specified and comprising of the following. |
| 64 | 150 mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate for foundation |
| 65 | Brick work 230 mm thick built in CM 1:4 |
| 66 | 15 mm thick rendering in CM(1:4) internally and externally to exposed surface of thick work including 150 mm below ground level |
| 67 | 100 mm thick coping in PCC 1:2:4 type B1 using 20 mm graded stone aggregate |
| 68 | MS covers made out of 50 mm thick MS plate with double hinges, fixed MS angle iron frame made out of MS angle iron 40 x 40 x5 mm thick including 150 mm long hold fast made out of MS flat iron of size 25 x 4 mm embedded in PCC coping MS covers shall be provided with suitable hand grip and suitable locking arrangement, |
| 69 | All MS surface shall ,be painted with two coats of synthetic enamel paints over a coat of red oxide primer complete all as specified. |
| 70 | M&L for Replacement of MS cover made out of 5mm thick MS sheet with double hinges and suitable handle locking arrengement etc complete fixed to MS angle iron frame made out of 40 x 40 x 5 mm size including 15cm long hold fast of 25 x 25 x 4 mm MS feate iron embeded in PCC coping for valve pit cover of various size necessary painting black synthetic enamelled paint with 2 coats over red primer. |
| 71 | M & L for painting to water supply tubing any dia after preparation of old painted surface by proper cleaning and then applying two coat of synthetic enamelled paint as per existing colour code or as directed by Engineer-in-Charge. |
| 72 | M&L for replacement of Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvansied iron strip 25 x 4 mm as earth lead by means of bolts, nuts, check nuts and washer os galvanised iron or steel all as shown in electrical platge No. 5 connected to earthing test point all as specified or indicated including testing on completion. |
| 73 | M&L in repair for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 25 x 4 mm galvanised iron strip. |
| 74 | M & L for painting to water supply motar & pump of 30/12.5/10 hp after preparation of old painted surface by proper cleaning and then applying two coat of synthetic enamelled paint as per existing colour code or as directed by Engineer-in-Charge |
| 75 | Supply and fix in repair water level indicator wireless liquid level indicator with overflow and empty alarm, 4 levels, long range up to 50 floors/ 5 KM , brass sensors all including electrical connection , installations and commissionings all as per standard specification and direction of EIC Make : Swarn Jal or equivalent |
| 76 | M&L in repair for Glowing sign boards at Pump house of size 6 feet x 3 feet x 1.5 feet aluminium strip box covered with accrelic sheet of suitable size duly stickered name of pump house of suitable size and colour code inclussive of LED light fitting inside box as specified and directed, |
| 77 | Suply, laying & jointing in repair/replacement in tranches DI pipes class K-7 of standard length spigot and socketed end push type self restrained joint with rubber gasket as jointing material, internal cement morter coating & external surface with butiminous paint 200 mm dia ISI complete all as specified and all as directed Engr-in-charge. all fixing ccessories deemed to included in rate. |
| 78 | All as per item No 58.00 above but size 150 mm dia DI pipe |
| 79 | All as per item No 58.00 above but size 100 mm dia DI pipe |
| 80 | All as per item No 58.00 above but size 80 mm dia DI pipe |
| 81 | Supply and fixing in repairs suction line made of GI tubes medium grade of 100/80 mm dia 3.3 meter long including flange joint with necessary welding work complete with all fittings (like; union, tee, bend, elbow, reducer, socket) to be fixed for suction line complete all as specified and directed by EIC. |
| 82 | M & L for Calcium hypochrorite powder/ Granules , available chorine 65% used for disinfection of water all as per standard specification and directed by EIC. |
| 83 | Supply and fixing in repair flat PVC multistranded copper conductor cable of size 6 sqmm x 3 core 36/0.5 including PVC pipe complete electrical connection to motor and starter all as specified and directed by Engr-in-charge. |
| 84 | Supply and fixing in replacement of high density polyethylene pipes (HDPE) of presure rating PN 6, DN 75 mm/ 63 mm 10 kgf/cm2 ISI marked,laid in borewell/ open well for water outlet including all connecting accessories complete all as specified and directed by Engr-in-charge. |
| 85 | Supply and fixing in replacement of stainless steel 63 mm dia,22.5 cm long Nipple medium grade complete all as specified and directed by Engr-in-charge. |
| 86 | Supply and fixing in replacement of mild steel, clamp 50mm x 5mm for support of HDPE pipe over borewell pipe of 150 mm dia including all connecting accessories complete all as specified and directed by Engr-in-charge. |
| 87 | S&F in replacement Informatory board of size 1.20 x 0.90n m made of aluminium sheet 2 mm thick with frame of stainless rectenger pipe 25x 15 mm and outer boarder of stainless steel pipe 35mm dia with packing of top cover canopy type shape and each sidw with marking of colour and pasted with heating process. The letters shall be 75 mm to 100mm high of white colour cut to shape with speical plotter, MES LOGO and in proper manner. The board shall be fixed 02 Nos stainless steel pipes of dia 75mm of 304 grade glossy finish, with NS plate 3 mm thick welded at bottom of pipes and board shall be fixed at height of 3.00m (Tope level of board) above GL and embedded and grouted in cement concret 1:2:4 type B-1 necessary excavation and earth complete all as specified and directed Note: Letter of writting word shalll be given by Engr-in-charge |
| 88 | Material and labour for rewinding the circulation centrigugal pump motor of capacity 1 HP, single phase 230 volts, 50 Hz capacity, disconnecting the electric connection of motors, and removing the motors from its existing position and sending to workshop for repairs/rewinding complete and refixing the same after repairs complete all as specified and directed by Engr-in-charge. Please Enable Macros to View BoQ information |
