|
| 1 | SUB WORK NO. 1 :- EXCAVATION WORK, ANTITERMITE TREATMENT, BACK FILLING OF EARTH , CARTAGE OF EARTH WORK & SAND FILLING Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kind soils. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.. All kinds of soil |
| 3 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 4 | Filling available excavated earth (excluding rock) in trenches ,plinth,sides of foundation etc . in layers not exceeding 20cm in depth ,consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m . |
| 5 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 6 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 7 | SUB WORK NO. 2 :- PLAIN CEMENT CONCRETE, PLINTH PROTECTION 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 8 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone- III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 9 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 10 | SUB WORK NO. 3 : - REINFORCED CEMENT CONCRETE, CENTER & SHUTTERING & REINFORCEMENT OF STEEL 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) strength shall not be less than M-20 |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). Strength shall not be less than M-20 |
| 12 | Centering shuttering including strutting, propping etc. and removal of form work FOUNDATION UP TO PLINTH |
| 13 | COL SUPER STRUCTURE |
| 14 | Roof Beam |
| 15 | Lintel+sunshade |
| 16 | Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete Thermo-Mechanically Treated bars. |
| 17 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 18 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. |
| 19 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 20 | SUB WORK NO 4 : - BRICK WORK IN FOUNDATION AND SUPER STRUCTURE 230 th Brick work with brick of class designation 75 in foundation & plinth in cement mortar 1:6 |
| 21 | Brick work with F.P.S bricks of class 75 in super structure above structure above plinth level up to floor five level in all shapes and sizes in cement mortar 1:6 (1 cement : 6 coarse sand ) |
| 22 | Half brick masonry with F.P.S bricks of class designation 75 in superstructure above plinth level up to floor five level in cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 23 | Extra for providing and placing in position 2 Nos. 6mm dia. M.S.bars at every third course of half brick masonry (with F.P.S.bricks). |
| 24 | SUB WORK NO. 5 : - DOOR , WINDOW & VENTILATOR FRAMES & SHUTTER & DOOR & WINDOWS FITTING Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 25 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 26 | Providing & fixing of wire mesh (mosquito jalli) with labour & material comlete With 12 mm mild steel U beading. |
| 27 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 28 | Providing and fixing chromium plated brass handles with necessary screws etc. complete: 75 mm |
| 29 | Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868),transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 30 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete |
| 31 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper |
| 32 | Providing and fixing PTMT door catcher of length 72 mm and dia. of 42 mm with suitable washers weighing not less than 33 gms. |
| 33 | Providing and fixing M.S. Tubular frames for doors and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 34 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 5.5 mm thick glass panes |
| 35 | SUB WORK NO. 6 : - FLOORING P/F 1st quality ceramic glazed wall tiles conforming to IS : 15622 of approved make in colours , shades except burgandy , bottel green , black of any sizes as approved by Engineer -in -Charge in skirting , risers of steps and dados over 12 mm thick bed of cement mortar 1:3 and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 36 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 37 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conformingto IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete |
| 38 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 39 | SUB WORK NO : - 7 INTERNAL , EXTERNAL PLASTER WORK, CEILING PLASTER , & FINISHING WORK 12mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 coarse sand) mortar |
| 40 | 15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 coarse sand) mortar |
| 41 | 6mm thick cement plaster of ceiling of mix 1:3 ( 1 cement : 3 fine sand) mortar |
| 42 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including water thinnable priming coat with cement primer |
| 43 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm) |
| 44 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable sq.m shade with ordinary paint of approved brand and manufacture. |
| 45 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 46 | SUB WORK NO. 8 : -WATER PROOFING WORK WORK Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed |
| 47 | Computer Cubicles (6 feet ) |
| 48 | Linear Running Table |
| 49 | Computer Chairs |
| 50 | Sitting Chairs |
| 51 | Air Conditioning Blue Star Cooling Only 1.5 Ton Star Wall Mount Split AC. |
| 52 | All in one PC/laptops for e-library system |
| 53 | Server |
| 54 | Switch |
| 55 | Core Router |
| 56 | IT Rack |
| 57 | Online UPS |
| 58 | Printer |
| 59 | Internet Connectivity |
| 60 | Inverter with 4 batteries |
| 61 | FLEXI LED BOARD with fixing all complete work. |
| 62 | 7.5 KVA kirloskar CPCB II green generator with foundation and instalation complete work. |
| 63 | Supply and fixing of fire extinguisher, ABC Type (IS1 Marked IS: 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. |
| 64 | Supply and fixing of C02 type fire extinguisher (ISI Marked IS: 2878 & TAC approved) along with supply of all materials and labour complete with initial charge and wall bracket, for proper completion of work. |
| 65 | Providing & fixing carbon steel Fire Man Axe with rubber insulated handle tested to 20000 volts. |
| 66 | Supplying and installing at approved location approved make fire buckets of 24 gauge galvanized steel sheet, standard of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letter \\"FIRE\\" in black and gold. Cost shall be inclusive of providing MS stand duly painted over a coat of primer (one stand shall be suitable for hanging 5 buckets). |
| 67 | 1200x900 mm (Indoor Cabinet) Only Frame |
| 68 | Providing and Fixing of Self illuminated/Auto Glow Exit Sigus printed on photo-luminescent sheet containing self illuminated base chemical, of appropriate size not less than 400x150mm, suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site. |
| 69 | Providing & fixing cast iron air release valve of 25 mm dia including 25 mm dia Ball valve with fittings etc. as per the requirement. |
| 70 | S/F of Street GI octagonal pole 7mtr long designed 410SP 36 including cement concrete in 1:3:6 including evevation backfilling etc. Along with 2mtr long single arm as per talk section and reducer sutaible size in arm respect as per. SI No 21.2 |
| 71 | Suppy and fixing street light fitting BRTFG 110-130 Watt IP 66 (AAA Approved in pwd sechdule) S.I. No. 23.16 |
| 72 | Supplying & Laying Aluminum conductor PVC insulated armored cable 1100 volts grade size 50sqmm 3-1/2 core at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks. On surfaace the cable shall be fixed on MS clamp etc. Complete in all respect the armouring of the cable shall be properly connected with the earth conductor by clamp etc. With ZigZag arrangment S.I. No. 501(j) |
| 73 | Supply and fixing of 2 core 1.5sqmm coper flexible cable of wiring of fixture of the pole (under pole) S.I. No.289(B) |
| 74 | S/B safe Earthing Electrode T-39 (Hot Dip Galvanized) for making suitable with crystalline conductive mixture complete S.I. No. 5.5 |
| 75 | S/I of water ATM/Watercooler with in built UV & RO Plant 150 LPH Purification capacity with raw water storage 500 ltr. HDPE water tank SS 250 Ltr. Chiller tank SS 500 Ltr. Both painel side stainless steel thick 5 mm number of FAUCET 2 power supply 230v 50hz 01 year warranty |
| 76 | Wiring point for light with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable in Surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI Box with Earthing the point with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable etc.as required. |
| 77 | Wiring point for Two way,light with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable in Surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI Box with Earthing the point with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable etc.as required. |
| 78 | Wiring point for fan with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable in Surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI Box with Earthing the point with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable etc.as required. |
| 79 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 80 | Wiring point for call bell with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable in Surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI Box with Earthing the point with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable etc.as required. |
| 81 | Wiring point for exhaust fan with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable in Surface/recessed medium class PVC conduit with modular switch, modular plate suitable GI Box with Earthing the point with 1.5 sq.mm FRLSH PVC insulated single core copper conductor cable etc.as required. |
| 82 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. Size 25 mm dia 16SWG (1.5mm)thick |
| 83 | Wiring point for plug with 1.5 sq.mm FRLSH PVC insulated multistrand single core copper conductor cable,with 5 amp flush type switch and 3 pin socket on existing board ,complete with 1.5 sq mm FRLSH PVC insulated multistrand copper conductor cable as earth wire.etc.complete in all respect,as directed, including matching colour wash. |
| 84 | Supplying and drawing of following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required |
| 85 | Wiring for circuit submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required |
| 86 | Wiring for circuit submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required |
| 87 | Wiring for circuit submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required |
| 88 | Wiring for circuit submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required |
| 89 | Wiring for circuit submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required |
| 90 | Supply and fixing of water tight oblong 10 Watt LED bulk head luminaire having die cast housing with driver set confirming to IP 65 and above Protection.Complete in all respect. CAT. - AAA |
| 91 | Supply and fixing of LED Tube Light with Metal heavy duty Box type batten Light fitting 1X22 watt suitable for upto 1X22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect.CAT. - AAA |
| 92 | Supply Installation, Testing and Commissioning of 1200mm sweep, BEE 5 star rated, ceilling fan with Brush Less Direct Curent (BLDC) motor, class of insulation : B, 3 nos. blades, 30 cm long down rod, 2 ns. Canopies shackle fit safety rope, copper winding, Power Factor not less than 0.9 Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS: 374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts washers, temperature rise= 75 degree C (max) insulation resistance more than 2 mage ohm, suitable for 230 V. 50 Hz,single phase AC Supply earthing etc. complete as required. |
| 93 | Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top .On surface the cable run shall be fixed on MS clamps etc.of suitable size or as directed by the Engineer-Incharge ,complete in all respect.The armouring of the cable shall be properly connected with the earth conductor by clamps etc.Following size |
| 94 | Supply and fixing of brass nickle plated compression gland for pvc insulated & armoured served sheaththed ,underground cable including rubber ring etc. complete in all respect. Thearmouring of the cable shall be properly connected with the earth as per direction of engineer -incharge.for cable |
| 95 | size 35 sq mm x 3-1/2core |
| 96 | Earthing with G.I. earth pipe 4.5 meter long 40mm die including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcol/ coke and salt as required. |
| 97 | Supply and laying of 25mm x 5 mm G.I. strip at 0.50 meter below graound as strip earth electrode including connection/ terminating with G.i nut bolt spring washer etc as required (joining shall be done by overlapping and with 2 sets of G.i nut bolt & spring washer spaced at 50mm) |
| 98 | Supply and fixing of one number 6 SWG G.I. wire in 15mm dia. G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site. |
| 99 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required. |
| 100 | Supply& Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entrise Electrical control panel with TPN ACB (65 KA,4Pole Elect draw out , Micor processer Release IPR2) and TPN MCCB's (Four Pole 36 KA with thermal magnatic release) Switches and instrument chamber etc.complete in all respects. |
| 101 | Supply and fixing of 240 volts C Curve 6-32 amp SP miniature circuit breaker (10 K A ) in existing MCB, DB complete with connections as required. |
| 102 | Supply and fixing of 440 volts C Curve 63 amp 4P miniature circuit breaker (10 K A ) in existing MCB, DB complete with connections as required. CAT A |
| 103 | Supply and fixing of 80-100 amp 4 pole MCCB (16 KA ) thermal magnetic relese. CAT A |
| 104 | Supply and fixing of flush/surface mounting 6 ways TPN distribution boards (Legrand Lexic) without MCB with additional metal door complete in all respects. As directed by engineer incharge. CAT A |
| 105 | Supply and fixing of flush/surface mounting 4 ways V TPN distribution board without MCB with additional metal door complete in all respects. As directed by engineer incharge. CAT A |
| 106 | Supply & Fixing single pole of MCB blanking plate. |
| 107 | Supply and Fixing of Danger Board fabricated from 10 gauge M.S. Sheet as per I.E. Rules |
| 108 | Supply & Erection and testing of Ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick G.I. down rod 19mm dia duly painted, complete in all respects. |
| 109 | Erection and testing of exhaust fan on the existing hole with suitable size rag bolt nut & washer etc. complete in all respects. |
| 110 | Supply and fixing of 16 gauge MS drum duly painted including making hole in the wall for exhaust fan and finshing propely complete in all respect. |
| 111 | Supply and fixing of power plug with 20A/250V flush type Moduler switch and 5 Pin 20A/250V flush type universal Moduler socket in suitable Conceled MS Box including supply of all material, labour,T&P etc.required for proper completion of work. |
| 112 | S/F of hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16SWGM.S. sheet incorporating 10mm dia, M.S. round barduly bent for supporting fan hanger dully painted withred oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting along with supply of all materials, labour T & P etc., for proper completion of work. |
| 113 | Supplying and fixing Telephone socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 114 | Supplying and drawing Co axial T V cable, RG-6 grade, 0.7 mm solid copper conductor, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/recessed steel/PVC conduit as required. |
| 115 | Supplying and drawing FR PVC insulated annealed copper conductor, unarmoured cable in the existing surface/recessed steel/PVC conduit as required. |
| 116 | Supply and fixing of Three phase multifunctional electronic energy meter 10 to 60 Amp. Capacity fitted in intergral box on wall complete in all respect. |
| 117 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : |
| 118 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern. |
| 119 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 120 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 121 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm |
| 122 | Single pushfit Coupler 110 mm |
| 123 | Single tee with door 110 mm |
| 124 | 110 mm |
| 125 | 110 mm |
| 126 | 110 mm bend |
| 127 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete |
| 128 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work - Exposed on wall 15 mm dia. nominal bore |
| 129 | 25 mm dia. nominal bore |
| 130 | 50 mm dia. nominal bore |
| 131 | Providing and fixing ball valve (brass) of approved quality complete High or low pressure with plastic floats 25 mm dia. nominal bore |
| 132 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : |
| 133 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 134 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 135 | Add 2.0% Contengency Please Enable Macros to View BoQ information |
