|
| 1 | Sub Head - 1 Concrete Work (A) |
| 2 | Cement Concrete with 4 cm gauge approved stone ballast, coarse sand & cement in the proportion of 4:2:1 including supply of all materials, labour, Tools & plants etc. required for proper completion of the work. (SOR-20/5.06/279)Same as above item no. 279 but with 2 cm. gauge stone grit instead of 4 cm. gauge stone ballast. (SOR-20/5.07/279(a)) |
| 3 | Cement Concrete with 4 cm gauge approved stone ballast, coarse sand & cement in the proportion of 8:4:1including supply of all materials, labour, Tools & plants etc. required for proper completion of the work. (SOR-20/5.08/281) |
| 4 | Extra for concrete work in superstructure above floor V level for each four floors or part thereof.DSR-18/4.14/AR |
| 5 | Sub Head -2 Brick Work |
| 6 | M-150 Brick work in 1:6 cement & fine sand 1.25 F.M. mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work. (SOR-20/6.02/303)Same as item no. 303 but in 1:3 one cement & three fine sand mortar.(SOR-20/6.05/306)Same as item no. 306 but in 1:3 one cement & three courase sand mortar.(SOR-20/6.06/307)As in item 303 to 307 above but in superstructure including necessary cutting & moulding of brick as required thickness of walls not to be less then 1½ brick.Add extra labour to above items.(SOR-20/6.07/309) |
| 7 | Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.DSR-18/6.5/AR |
| 8 | Sub Head - 3 Wood Work |
| 9 | Wood chaukat sectionCP Teak wood (SOR-20/22(A)P-05 |
| 10 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.DSR-18/9.21.1/AR |
| 11 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) Over item no. 9.20 and 9.21.DSR-18/9.23/AR |
| 12 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.5 mm thick.DSR-18/9.127/AR |
| 13 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.(DSR-18/9.83/AR) |
| 14 | Sub Head - 4 Steel Work |
| 15 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:DSR-18/10.2/AR |
| 16 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes.DSR-18/10.16.2/AR |
| 17 | Sub Head - 5 Flooring Work |
| 18 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels.Granite of any colour and shade. Area of slab over 0.50 sqm.DSR-18/8.2.2.2/AR |
| 19 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work.DSR-18/8.3.2/AR |
| 20 | Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete.DSR-18/8.4/AR |
| 21 | Extra for providing opening of required size & shape for wash basins? kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.DSR-18/8.5/AR |
| 22 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1: 4 (1 cement : 4 coarse sand) : 25 mmDSR-18/11.26.1/AR |
| 23 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.DSR-18/11.27/AR |
| 24 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : |
| 25 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. DSR-18/11.55.1/AR |
| 26 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. a) Size of Tile 600 x 600 mm DSR-18/11.41.2/AR |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specified by the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cementmortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matchingshade complete.DSR-18/11.36/AR |
| 28 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.DSR-18/11.37/AR |
| 29 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in charge. (The panel shuttering work shall be paid for separately).(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).DSR-18/16.75/AR |
| 30 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600 x 600 mm.DSR-18/11.48.2/AR |
| 31 | 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with |
| 32 | Second class teak woodDSR-18/11.33.1/AR |
| 33 | Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.DSR-18/16.92/AR |
| 34 | Sub Head - 6 Finishing Work |
| 35 | 12 mm cement plaster of mix 1:6 (1 cement: 3coarse sand).DSR-18/13.4.2/AR |
| 36 | 15 mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement: 3coarse sand)DSR-18/13.5.2/AR |
| 37 | Providing and applying plaster of paris putty of 2 mm thickness of plastered surface to prepare the surface even and smooth complete.DSR-18/13.26/AR |
| 38 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer.DSR-18/13.43.1/AR |
| 39 | Distempering (first coat) with oil bound distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including a priming coat with cement primer of approved brand and manufacture such as Berger, J&N, Shalimar, Asian Paint after thoroughly brushing the surface free from mortar dropping and other foreign matters and also including the surface even with plaster of Paris or approved synthetic materials and sand papered smooth including supply of all materials, labour, Tools & plants etc. required for proper completion of the work.SOR-20/15.09/649 |
| 40 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work.DSR-18/13.52.1/AR |
| 41 | Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately) |
| 42 | Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.AR/GNIDA |
| 43 | Based on DSR18/ 8.22) Providing and fixing adjustable stainless steel cramps of approved quality and of required shape and size adjustable with stainless steel nuts bolts and washer (total weight not less than 260 gms) for dry stone cladding fixed on frame work- at suitable location including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge. |
| 44 | Providing wall putty on new surface with approved quality material of Berger/ J.K./Birla or similar make 2 coats. (sor new item ch.- 8) |
| 45 | Providing wall putty on old surface with approved quality material of Berger/ J.K./Birla or similar make 2 coats. (sor new item ch.- 8) |
| 46 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm DSR/18/13.45.1 |
| 47 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.DSR/2018/13.26 |
| 48 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.DSR/2018/13.80 |
| 49 | Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge.Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works. (DSR-18/24.2/AR) |
| 50 | Providing and fixing in wall lining flat pressed three layer (medium density) particle board or graded wood Pre-laminated one side decorative lamination and other side balancing lamination Grade I, Type II, IS : 12823 marked, including priming coat on unexposed arrangement and screws etc. complete : 12 mm thick.DSR-18/8.26/AR |
| 51 | Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. Sal Wood.DSR-18/9.3.1/AR |
| 52 | Sub Head - 7 Roofing/False Ceilling Work |
| 53 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 54 | GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.DSR-18/12.52.2/AR |
| 55 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : |
| 56 | 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 57 | 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)DSR-18/12.45.1/AR |
| 58 | Sub Head - 8 Aluminium Work |
| 59 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately. DSR 18 /21.18/AR |
| 60 | Providing and laying S&S C.I. standard specials such as tees, bends, collars, tapers, caps etc. (Heavy class): Over 300 mm diaDSR-18/18.25.2/AR |
| 61 | Sub Head - 9 Water Proofing Work |
| 62 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height includingcleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. |
| 63 | (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimumthickness at khurra as 65 mm.DSR-18/22.7/AR |
| 64 | Sub Head - 10 Other Miscellaneous Non Schedule Items |
| 65 | Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.DSR/2018/25.8/AR |
| 66 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge.DSR-18//21.2/AR |
| 67 | Pre-laminated particle board with decorative lamination on both sides.DSR-18/21.2.2/AR |
| 68 | PLUMBING WORK (B)Sub Head - 11 Sanitary Installations |
| 69 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 200mm. (DSR-18/17.10.1.3/AR) |
| 70 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipes. 40 mm dia.(DSR-18/17.28.1.2/AR) |
| 71 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.(DSR-18/17.78/AR) |
| 72 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.(DSR-18/17.80/AR) |
| 73 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore.DSR-18/18.51.1/AR |
| 74 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore.DSR-18/18.53.1/AR |
| 75 | Sub Head - 12 Sanitary Installations (Non Scheduled Item) |
| 76 | Providing and fixing white vitreous china oval wash basin for under counter installation with special fabricated brackets painted white, faucets as required, 32 mm C.P. brass waste.32 mm C.P. brass bottle trap & pipe to wall with rubber adopter for waste connection and C.P. brass wall flange complete in all respects including cutting and making good the walls where required. Oval wash basin size 528 x 412 mm Parry Cat No. C-841M or approved equivalent, with brackets, 32 mm CP brass waste Jaquar Cat. No. ALD 709, C.P. sensor operated faucet Jaquar Cat. No. SNR CHR 51011 or approved equivalent. 32 mm C.P. brass bottle trap with pipe to wall and C.P. wall flange Jaquar Cat. No. ALD 769 L 250 X190.AR/GNIDA |
| 77 | Wash basin size 565 x 410 mm American Standard Model No. TF- 0514 or approved equivalent, with brackets, 32 mm CP brass waste kohlar model K-45432 IN, C.P. basin mixer American standard model no. WF-0301.151.50 or approved equivalent. 32 mm C.P. brass bottle trap Kohlar Make model no-K-16407IN-CP with pipe to wall and C.P. wall flange. AR/GNIDA |
| 78 | Providing and fixing white vitreous china flat back wash basin with C.I. or M.S. brackets painted with 15mm C.P. sensor faucet, 32mm C.P. brass waste, 32 mm C.P. brass bottle trap with C.P. pipe to wall , C.P. wall flange and rubber adapter for waste complete including cutting and making good the walls where required. Flat back wash basin size 550x440mm Parry Cat. No. C0404 or approved equivalent, C.P. Sensor faucet Jaquar Cat No. SNR CHR 51011 or approved equivalent 32 mm C.P. brass waste with C.P. chain & rubber plug Jaquar Cat No. ALD 705 or approved equivalent, 32 mm C.P. brass bottle trap with pipe to wall and C.P. wall flange Jaquar Cat. No. ALD 769 L 250 X 190 or approved equivalent (For handicapped toilets).AR/GNIDA |
| 79 | Providing and fixing 15mm C.P. copper connecting pipe 450mm long with C.P. brass nuts, washers complete in all respects.(Jaquar Cat No. ALD 803AB or approved equivalent).AR/GNIDA |
| 80 | Providing and fixing C.P. cast brass twin coat hooks fixed to PVC rawl plug with SS screws Jaquar (Cat. No. ACN-1161N) or approved equivalent. AR/GNIDA |
| 81 | Providing and fixing C.P. cast brass twin coat hooks fixed to PVC rawl plug with SS screws Jaquar (American Standard Art.MN-4403) or approved equivalent.AR/GNIDA |
| 82 | Providing and fixing health faucet with 1 m long flexible tube and wall hook including all fittings (Jaquar Cat No.ALD 573) or approved equivalent. AR/GNIDA |
| 83 | Providing and fixing health faucet with 1 m PVC tube and swivel hook including all fittings (American Standard Model No-TP-405) or approved equivalent.AR/GNIDA |
| 84 | Providing and fixing white vitreous china urinal partition with expandable anchor fasteners with C.P. brass bolts and washers complete, including cutting and making good the walls where required. Division plate Parryware Cat No. C0507 or approved equivalent.AR/GNIDA |
| 85 | Providing and fixing 6mm thick bevelled edge plate glass mirror of approved quality with 6mm thick hard board backing fixed to wooden cleats with CP brass screws and washers. AR |
| 86 | Providing and fixing 15mm C.P brass mixing fitting for kitchen sink with swinging spout complete. Including cutting and making good the walls wherever required . C.P. brass mixing fitting Jaquar cat. No. CON-319KN or approved equivalent.AR/GNIDA |
| 87 | Providing and fixing stainless steel recessed type toilet paper holder with flap and aluminium roller complete, including cutting and making good the walls where required. (Jaquar Cat. No. AHS-1553) Recessed toilet paper holder with aluminium roller.Jaquar code AHS-1553.AR/GNIDA |
| 88 | Recessed toilet paper holder with roller.American Standard Model no- WF-6586.908.50Seva Tissue Holder.(For VIP Tower-1 & Tower-4) AR/GNIDA |
| 89 | Providing and fixing Grab bar including all fittings complete.(Jaquar Cat. No.-AHS-1507)AR/GNIDA |
| 90 | Providing and fixing fully automatic hand dryer including all fittings complete.(Utec model-UT-525)AR/GNIDA |
| 91 | Providing and fixing fully automatic soap dispenser(ABS body) with capacity 800 ml. including all fittings complete.(Utec Model-UT - 3AM)AR/GNIDA |
| 92 | Providing and fixing fully automatic soap dispenser(ABS body) with capacity 800 ml. including all fittings complete.Kohlar Model-5487K- CP (For VIP Rooms Tower -04).AR/GNIDA |
| 93 | Providing and fixing vertical storage type hot water heater fixed to wall with anchor bolts & nuts, 15mm CP brass angle stop cock and 15mm CP brass non-return valve complete including making connections with 15mm dia CP connecting pipes on inlet and outlet, suitable length of power cable and 15 amps plug (Venus or approved equivalent). |
| 94 | Capacity 25 Litres Model 25 GV (for VIP toilets & Pantry) AR/GNIDA |
| 95 | Capacity 50 Litres Model 50 GV (for kitchen).AR/GNIDA |
| 96 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 455 x 370 mm having pre & post flushing with water, having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.Make-American Standard model no-WP-6506.402.04) AR |
| 97 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893.15mm nominal bore.Make American Standard Model No-A-4400.AR/GNIDA |
| 98 | Providing and fixing shower set comparising of following including cutting and making good the walls where required. One No. CP Brass single lever mixer diverter cum bath spout Jaquar Model KUB-35137F or approved equivalent). One No. CP Brass over head shower with arm Jaquar Model OHS- 1719 + SHA-487 or approved equivalent).Shower set as described above AR/GNIDA Please Enable Macros to View BoQ information |
| 99 | Providing and fixing shower set comparising of following including cutting and making good the walls where required. One No. CP Brass single lever mixer diverter cum bath spout Jaquar Model KUB-35137F or approved equivalent). One No. CP Brass over head shower with arm Jaquar Model OHS- 1719 + SHA-487 or approved equivalent).Shower set as described above AR/GNIDA Please Enable Macros to View BoQ information |
