Tender For Remoddeling Of Lis Dobber Patta In Teh.Nadaun Distt.Hamirpur (Hp)(Sh:-L/J Of Hdpe Distribution Networks & Construction Of Outlets Under Lis Dobber Patta), Nadaun-Himachal Pradesh
TDR : 54983489
Tender Notice
BOQ
5 Days Left
Nadaun
Himachal Pradesh
Tender For Remoddeling Of Lis Dobber Patta In Teh.Nadaun Distt.Hamirpur (Hp)(Sh:-L/J Of Hdpe Distribution Networks & Construction of Outlets Under Lis Dobber Patta)
Name of Work:- Remoddeling of LIS Dobber Patta in Teh.Nadaun Distt.Hamirpur (HP)(sh:-L/J of HDPE Distribution Networks & c/o outlets under LIS Dobber Patta)
Sl. No.
Item Description
1
Excavation in foundations and trenches (for pipes and pits) upto all depths etc. in all kinds of soil such as pick work, jumper work , saturated soil chiseling or wedging out of rock where blasting is prohibited in all leads and lifts including trimming and dressing of sides, leveling of beds to correct grade including shoring strutting, planking timbering and dewatering wherever required, stacking usable and unusable material/soil separately and after laying jointing and testing of pipes, returning the stacked soil in 15 cm layer by ramming and watering and then disposing of all surplus excavated soil/unusable material as directed within all leads and lifts including restoration of unmetaled/ mattelled /paved surfaces to its original condition and including cost of diversion of traffic, night signal boards, fixing, caution, boards, crossing over trenches for access to houses, fencing etc. compete in all respects within all leads and lifts as per the direction of Engineer-in-charge.
2
Laying in trenches HDPE pipes of following diameters & classes as per IS 4984 , PE-80 and jointing the pipes through push type compression joints by hydraulically operated machines upto 110 mm diameter and butt fussion ( heat fusion process) above 110 mm diameter i/c necessary fittings,bends,tees & reducers fabricated in accoradance with IS 8360 & IS 8008 with latest ammendments & shall be provided as per site conditions.Flanging of the pipes shall be made as& where required confirming to code IS 8008 & IS 7634, stub ends will be welded on pipes & MS flange shall be provided with slip on covered by epoxy coating/plastic powder. The flange should be confirm to ANSI B 16.5 with necessary nuts & Bolts. Jointing shall be complete in all respects i/c testing at site upto entire satisfaction of engineer-in charge.
3
PN 4.0 , Class , PE-80
4
180MM
5
140MM
6
90mm PE 80
7
Providing and laying cement concrete 1:4:8(1 cement:4 sand:8 graded stone aggregate 40 mm N/size)and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.
8
Providing and laying cement concrete work 1:1:5:3 (1 cement :1.5 sand 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of from work and reinforcement for reinforced FOR RCC
9
Fixing 90 mm dia HDPE inlet pipe.
10
Providing and Fixing RCC Pipe NP-2 350 mm.dia
11
Providing and Fixing RCC Pipe NP-2 900 mm.dia
12
Providing and Fixing 80 mm dia control/sluice valve Bir/Kartar make
13
Providing and laying Precast slab in designed cement concrete MIX of M25 and curing complete excluding cost of form work
14
Steel work welded in built up section ,trusses & frames work including cutting,histing,fixing in position & applying a priming coat of red lead paint :- in Grating,framedGaurd,bars,ladders,railing,bars,bracket & Similar work.
15
Pervision for locking arrangements & other accessories Please Enable Macros to View BoQ information
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
