|
| 1 | Taking down chowkats or frames with shutters ( without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 sqm each and removing to store. complete all as specified and directed. |
| 2 | All as per item No 1 but n'exc 1.5 Sqm each. complete all as specified and directed. |
| 3 | Taking down shutter of any description exc. 1 sqm but not exc 2 Sqm each complete all as specified and directed. |
| 4 | Supply & Fixing PVC door frame (50x47) mm made out of plain colour 5 mm thich PVC Sheet reinforced with MS Square Tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed. |
| 5 | S&F 30 mm thick factory made solid panel PVC door shutter ( Style ) consisting of frame made out of MS Tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC ' C 'Channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC Sheets for top rail , lock rail & bottomrail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC Sheet to be fitted in the MS Frame welded / sealed to stiles & rails with suitable PVC Sheet beading, jointed together with solvent cement,supplying & fixing in the frame at site as per specification & drawing. complete all as specified and directed. |
| 6 | S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 105 X 60mm. Complete all as specified and as directed. |
| 7 | S & F for 30 mm thick 2nd class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and as directed. |
| 8 | S & F 35 mm thick factory made glazed & skeleton shutter of 2nd class hard wood open rebated and prepared to receive gauge (divided into squares with sash bars) edges of framing plain chamfered or rounded, fitted without & fitted beads for securing glass etc, sizes of members of shutters as specified in SSR Pt-I Sec-8 clause 8.23 (a) and fitted to chowkhats complete all as specified and as directed. |
| 9 | S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.complete all as specified and as directed. |
| 10 | S&F, in repair 18/19 mm thick pre laminated particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work as in cup board shutters, partitions, shelves, kitchen cabinet and similar work. Complete all as specified and directed. |
| 11 | S&F stainless steel wirecloth 0.36 mm nominal dia of wire and average aperture 1.40 mm and fixed with stanless steel wire staples complete all as specified and directed. |
| 12 | S&F 3.0 mm th sheet glass ordinary quality plain and glazing with oil putty in square n'exc .5 sqm in each pane.Complete all as specified and as directed. |
| 13 | S & F of 100 mm long aluminium anodised barrel tower bolt complete all as specified and as directed. |
| 14 | S & F of 150 mm long aluminium anodised barrel tower bolt complete all as specified and as directed. |
| 15 | S & F of 100 mm long extruded anodised aluminium alloy handle, complete all as specified and as directed. |
| 16 | S & F of 150 mm long extruded anodised aluminium alloy handle, complete all as specified and as directed. |
| 17 | S&F 100 mm MS, Butt hinges,medium weight cold rolled fixed with screw or welding complete all as specified and as directed. |
| 18 | S&F 125 mm MS, Butt hinges,medium weight cold rolled fixed with screw or welding complete all as specified and as directed. |
| 19 | S & F of 300 mm long (Length of bolt) aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, cast or extruded sections and fixing bolts and sliding bolt or cast aluminium alloy complete all as specified and directed. |
| 20 | Taking down cement plaster of any description of brick or stone wall etc incl racking out joints and hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 21 | Demolition brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified and directed. |
| 22 | M&L for brick work with sub class 'B' brick in cement mortar 1:6, straight or curved on plan exc 6 m mean radius, complete all as specified |
| 23 | M&L for rendering 15 mm thick in CM 1:4 on old fair faces of brick work or concrete surface even and smooth using water proofing compound (WPC) & without using extra cement all as specified and as directed by Engr-in-charge. |
| 24 | M&L for rendering 15 mm thick in CM 1:6 on new fair faces of brick work or concrete surface even and smooth using water proofing compound (WPC) & without using extra cement all as specified and as directed by Engr-in-charge. |
| 25 | M&L for preparing new plastered surfaces & applying two coats of cement base paint on walls. all as specified and as directed by Engr-in-charge |
| 26 | M&L for preparation of new surfaces plastered or unplastered new surfaces & applying two coats of oil emulsion distemper on walls. all as specified and as directed by Engr-in-charge |
| 27 | Demolition of concrete ( unreinforced ) in ground floors and paving nexc 15 cm thk (below or above ground level) complete all as specified and directed. |
| 28 | M & L 75 mm thk Cement concrete (1:3:6) type C-2, (40 mm gr agg) as in plinth protection finished even and fair complete all as specified and as directed. |
| 29 | M & L 75 mm thick PCC type D2 1:4:8 (40 mm Gr. Agg ) as in sub base complete all as specified.and as directed. |
| 30 | M&L for laying machine pressed precast concrete interlocking reflective coloured (Glossy finish)pavers block any shape and size confirming to IS 15658-2006 of 55mm to 60mm thick, M-35 Grade over 30 mm thick sand layer watering and ramming and including dismantling of tiles of any description or thickness laid dry or laid dry and pointed etc. complete all as specified. |
| 31 | M& L Chequared Cement Concrete (Glossy) Tiles 30 CM x 30 CM X 25 mm th set and jointed in cement slurry and pointed in neat grey cement & pigment in floors over screed bed 15 mm thk in cm 1:6 including dismantling of tiles of any description or thickness laid bedded and pointed in any mortar etc.complete all as specified. |
| 32 | M&L for machine cut kota stone slab flooring 20-22 mm th over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl cutting, rubbing and polishing to receive mirror finish over 15 mm th screed bed in CM 1:6 complete all as specified and as directed. |
| 33 | M & L for 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) in sub base for hard standing complete all as specified and as directed. |
| 34 | M&L for 40 mm thick plain cement concrete 1:2:4 type B-1 using (20 mm graded stone aggregate) as in floor,finished rough to receive tiles etc,complete all as specified. |
| 35 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and directed. |
| 36 | Material and labour for 20 mm thick granite stone machine cut (table rubbed and polished) bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigments to match the shade of granite stone including grinding and polishing, rounding to edges of granite stone etc.complete all as specified and directed. |
| 37 | M&L for Machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed no pigment to match the shade of the slab including rubbing and polishing complete all as specified. |
| 38 | M&L for Marble work green marble 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with green marble shade complete all as specified. |
| 39 | Dismantling floor hearth or wall tiling incl cement mortar bedding/plaster (but not backing) and removing rubbish off the premises etc complete all as specified and directed. |
| 40 | M&L for 25 mm thick plain cement concrete (1:2:4) type B-1 using (20 mm graded stone aggregate) as in Sub base for leveling ,complete all as specified and directed. |
| 41 | M&L for Non-skid coloured Ceramic tiles of size 300 x 300 x 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles over and including 15mm thick Screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified. |
| 42 | M&L for vitrified coloured tiles 10mm th (square/rectangular) polished area of each tile 0.30 sqm but n exc 0.42 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm th screed bed in CM 1:6 complete all as specified and directed. |
| 43 | All as per item No 43 but on skirting over 10 mm th rendering in CM 1:4 complete all as specified and directed. |
| 44 | M&L for glazed coloured ceramic tiles 350 mm x 250mm/450mmx350x7 to 8 mm thick as in vertical surfces set & jointed in neat cement slurry & pointed in coloured cement with & including backing coat 10mm thick in CM 1:4 complete all as specified and directed. |
| 45 | Dismantling Plain or corrugated steel (corrugated/ semi corrugated etc) sheet in roof covering complete all as specified and as directed. |
| 46 | Dismantling wrought iron or mild steel work of any description not otherwise provided for .complete all as specified and directed. |
| 47 | S&F Tubular Sections as in main cross beams , hip and jack rafters; purlins, where connected to common rafter , posts etc. conf to Fe-410-w(gdeE-250 quality-A) complete all as specified and as directed. |
| 48 | M &L for MS work as in wind tie or any other work incl cutting, drilling holes etc. complete all as specified and directed. |
| 49 | S & F 0.5mm thick corrugated pre painted / coloured galvalume sheet in roofing fixing all as per manufactures instructions with all fittings and accessories etc complete all as specified and directed. |
| 50 | All as per item No 49 above above but plain sheet fix in valley gutter / ridge / view cutter complete all as specified and directed. |
| 51 | M & L for Providing and carrying out water Proofing treatment to toilet, sunkan slabs, wet areas etc, after applying 15mm thick cement plaster in cm (1:4) complete and proper surface prepration, carry out cementitious ingection grouting at leakage point using cebex 100 plasticised expanding grounding admixture, application of polymer modified at slab wall junction using Nitoband SBR latex screen modifier cum bonding agent and application of two coat of brushbond RFX two part acrylic polymer modified cementitious elastomeric waterproof and protective coating etc, complete all tools and plant as per manufacturers specification paint complete all as specified and directed by engr-in-charge. |
| 52 | M &L for two coat of synthetic enamel paint over a coat of red oxide primer, including preparation of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described complete all as specified and directed. |
| 53 | Dismantling wall/ ceiling boards(fibre pulp insulation etc.) or insulations boards /slabs/blankets any thickness incl. cover fillets and alum snip grid. complete all as specified and directed. |
| 54 | S & F Anodised Alu. Snap grid 605x605 mm frame wk for false ceiling and providing 9mm th Acoustical board/tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed in celing with screws to frame work or with staples on snap grid including hangers 3 mm dia G.I. ( up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 X 3 mm size 60 mm long complete all as specified and directed. |
| 55 | M&L for false ceiling with 10mm thick of panel size 600mm x 900mm plaster of paris sheets fixed with machine screws on GI channel 18 gauge thick, grid work main joists placed at 750mm centres, secondary joists placed at 450mm centres, GI angle suspenders from roof and treating the plaster of paris sheets with thin layer of pop with Gypsum binder, sanding the surfaces till smooth surface is obtained including preparation of surface and applying two coats of oil bound distemper over a coat of primer all as specified and as directed.Make: Gyproc or Equivalent |
| 56 | M & L for preparation of new wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 57 | S&F External teak wood lipping 6 mm thick for 18/19 mm thick particles board, block board or veneered particle board fixed with nails. complete all as specified and directed. |
| 58 | S&F, 100mm size Hasp and staple, safety type aluminium anodized stove enameled black with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed |
| 59 | S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised 30mm width of flaps complete all as specified and directed. |
| 60 | S&F 40 mm dia, mild steel bright finished cup board knobs fixed with nut, screw and washer complete all as spd and as directed. |
| 61 | S&F, Ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in complete all as specified and as directed. |
| 62 | Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including frame and necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws, mortice lock, door stooper, hydraulic door closer, other fitting arrangements as required etc.and 4.8 mm thick sheet glass ordinary quality plain and glazing Complete all as specified and directed. |
| 63 | S&F Anodised aluminium window and ventilator shutters, (three Track) fixed type without sash bar, aluminium section weight not less 0.55 kg/m including frame and necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, srews with powder coating of any colour (Thickness or powder coating not less than 50 micron) including stainless steel wirecloth 0.36 mm nominal dia of wire and average aperture 1.40 mm and fixed with stanless steel wire staples. and 3.0 mm th sheet glass ordinary quality plain and glazing Complete all as specified and as directed. |
| 64 | S & F for 10/12 mm thick toughened glass with etching fixed with necessary Ozone patch touch fittings including openable door chamfered edge polishing as in bathing cubical / partitions including all fitting and fixture as per manufasture instructions etc. complete all as specified |
| 65 | S & F in repair for aluminium powder coated partition using 'Jindal' aluminium SP/DP section or equivelent make as specified with 5mm thick tinted glass, PVC rubber beading, 12mm thick prelaminated partical board fixed with glazing clips etc complete all as specified and as directed, section SP (single partition) -20033, DP (double Partition)- 20034, glazing clips -4407 |
| 66 | S&F for pressed steel door frames with one or more rebates incl necessary fixing lugs, hinges, lock strike plates of size 125 X 60mm. Complete all as specified and as directed. |
| 67 | M&L for rendering 10mm thick in CM 1:4 on concrete surfaces over roof slabs with admixture of integral water proofing compound @ 3% by weight of cement (WPC shall be measured & paid seperately) |
| 68 | M&L for taking out old water proofing treatment using polymerised membrane to roof slab. Water proofing treatment shall be as under:-(a) The roof surface shall be thoroughly wire brushed, washed, dried up & cleaned to remove all foreign materials & dust to receive primer. (b) On the dried roof surface, apply one coat of bituminous primer @ 100 Gm/ Sqm as per manufacturers instruction.(c) On this primed surface, the approved APP modified bituminous membrane with non woven polyester mat asreinforcement weighing not less than 3.5 Kg/ Sqm laid by torch application metho and top surface shall be applied with bituminous aluminium paint.(d) The overlap while torching shall be 75mm on longitudinal direction & 100mm on transverse direction. Please Enable Macros to View BoQ information |
