|
| 1 | Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 cm thickness below and above ground level, complete all as specified and directed. |
| 2 | Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles. |
| 3 | M & L for brick work using old size fly ash brick, straight or curved on plan exc 6m mean radius, built in CM (1:6), complete all as specified and directed. |
| 4 | M&L for PCC type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) as in surface channel and drain beads including all necessary form work including demolition complete all as specified and directed. |
| 5 | Extra performing fair finished drain or channels cement concrete girth not less than 50cm using extra cement including forms, mould, mitied/ stopped ends etc. complete all as specified and directed. |
| 6 | Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed. |
| 7 | M&L for rendering 15 mm thick in cement mortar 1:6 on fair face of brick work of walls, finished even & smooth without using extra cement, complete all as specified and directed. |
| 8 | M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement, complete, all as specified. |
| 9 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over and including one coat of primer and one coat of min 1mm thick putty complete, all as specified and directed. |
| 10 | M&L for preparation of new plastered surfaces of ceilings and applying two coats of oil emulsion distemper (OBD) on ceiling of approved shade/tint over and including a coat of primer and a coat of min 1mm thick putty completeall as specified and directed. |
| 11 | Complete removal of existing treatment from wall and applying two coats of oil bond distemper (OBD) over a coat of primer over a coat of wall care putty (2 mm thick) to make surface even and smooth, and complete all as specified and directed. (Rate shall be inclusive of scafolding and other arrangement upto 25m height) |
| 12 | M&L for preparation of old decorated surfaces of ceiling by washing, rubbing down and stopping of distempered surfaces and applying two coat of oil emulsion distemper (OBD) of approved shade/tint complete, all as specified & directed.(Rate shall be inclusive of scafolding and other arrangement upto 25m height) |
| 13 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces all as per manufacturers instruction and directed by EIC.(Rate shall be inclusive of scafolding and other arrangement upto 25m height) |
| 14 | Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 15 | M&L for Non skid coloured full body Vitrified tiles tiles group BI(a), Premium quality 8 to 9 mm thick (square/ rectanglar) area of each tiles exc 0.18 Sqm but not exc 0.36 Sqm as in floor over and including screed bed 15mm thick in CM 1:6 or beding layer for laying floor finishes etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete, all as specified and directed. |
| 16 | M&L for coloured, glazed, ceramic tiles premium quality 600X300X7mm/600x450x7mm thick but as on vertical surfaces such as skirting/dado over and including 10mm thick rendering in CM 1:4, complete all as specified & directed. |
| 17 | M&L for 18-20 mm thick granite (of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like, over 15mm thick screed bed in cement mortar (1:6) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite and rounding the edges and making holes for gas pipe as required , after dismantling of old granite complete all as specified and directed. |
| 18 | M & L for 40 mm thick cement concrete type B0, 1:2:4 (12.5mm graded aggregate) as in flooring and similar complete all as specified and directed. |
| 19 | M&L for fine Sand cushioning under floors including watering and consolidation complete all as specified and directed. |
| 20 | M&L for Coloured machine pressed/vibro mechanically floated interlocking paver block any shape and size confirming to IS - 15658-2006 of 80 mm thickness, M-35 grade, with topping of cement mixed with imported pigment colour and shape shall be approved and including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed by Engr-in-Charge. |
| 21 | M&L Cement concrete rich colored chequered tiles machine pressed with imported pigment smooth finish of size (300 mm x 300 mm or any size as approved 20 to 25 mm) thick set and jointed with neat cement slurry including including screed bed 15mm thick in CM 1:6 or beding layer for laying floor finishes etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete, all as specified and directed. |
| 22 | Roughing surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @3kg/Sqm mixed with water proofing compound including 20mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound complete all as specified and directed. (WPC shall be measured and paid separatley) Note : No extra cost shall be paid to contractor in r/o any removal of existing roof treatment. |
| 23 | M & L a coat of cold applied bituminous primer over cleaned surface @ 0.50 Kg/Sqm and laid 3mm thick APP modified five layer ploymeric membrance, minimum wt 3.60 Kg/Sqm reinforced with polfyester non woven fabric (weighing not less than 150gms/Sqm) with torch application mathod as per the manufacturer instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces wih grooves & make good in cement mortar 1:3 , finally if required & finally finished with bituminous aluminium paint @ 0.20 Kg/Sqm etc complete all as spefified including taking down existing roof treatment from the RCC slab, cleaning off all foreign material by wire brushing cleaning off surface and removal of spoil to a distance n.exc 500 mtr complete all as directed. Make Approved by GE. NOTE :- (a) Work shell be executed by authorised applicator of manufacture as per manufacturers instructions and upto roof hight of tripple stories building.(b). 10 years of manufacture s guarantee shall be excuted in smart assurance system complete all as spfd and directed. (Incl removal of existing roof treatment / padding) |
| 24 | M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls. |
| 25 | S&F in repairs galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors. |
| 26 | S&F in repair single piece Vitreous china any shade cascade floor mounted single piece water closet P/S trap with dual flush cistern for UF soft close slim seat cover, hinges fitting, conversion bend, fixing accessories set complete all as specified and directed. Make : Jaquar Cat part No OPS-WHT15753NS250UFSMZ/ Cera cat part No S1013105/Kajaria cat part No KB-3007 |
| 27 | S&F Vitreous china full set pedestal type wash basin, white, flat back, size 585x450x220mm including bracket, CP brass waste coupling and waste pipe fixed in repair complete all as directed. Make : Jaquar Cat part No Jaguar FLS-WHT-5801 & 5301/Cera cat part No S2040112 & S2090107 or equivalent in Kajaria/Somany |
| 28 | S&F in repair Vitreous China urinals, half stall type (flat back), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including spreader, 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed |
| 29 | S&F Viterous China full set automatic urinal sensor both pre and post flush water required white including waster pipe etc. \\"as in repair\\" complete all as specified and directed. |
| 30 | S&F 32 mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified. |
| 31 | S&F PVC connection 450 mm long suitable for 15 mm bore GI pipe including CP brass nuts on both sides, complete all as specified & directed. |
| 32 | S&F 15mm bore long body bib tap cast copper alloy chromium plated fancy type with wall flange and aerator fixed in repair complete all as specified and directed. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series |
| 33 | S&F CP fancy type Angle valve 15mm dia (angle cock) cast copper alloy with wall flange. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series |
| 34 | S&F in repair 15mm bore concealed type, stop valve cast copper alloy screwed down high pressure with capstan head and cup, screwed both ends for iron pipe or for union complete, all as specified & directed.Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series |
| 35 | S&F in repair 15mm bore fancy type two way CP Brass Bib taps with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed .Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series |
| 36 | S&F CP brass hot & cold single lever basin mixer with 450mm long braided hoses cast copper alloy with centre hole for WHB complete all as directed by Engineer-in-charge. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series |
| 37 | S&F CP brass hot & cold single lever basin mixer with 450mm long braided hoses cast copper alloy with centre hole for WHB complete all as directed by Engineer-in-charge. Make : Jaquar Opal Prime Series/ Cera Ruby series/Somany Bellis Series |
| 38 | S&F in repairs CP brass tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flanges, fixed to PVC rawl plugs with chromium plated brass screws, complete all as specified. |
| 39 | S&F in repairs bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial Ply wood backing fixed to wooden plugs with chromium plated brass screws and cup washer, complete all as specified and directed. |
| 40 | S&F in repair CP brass health faucet not exc 1.25 m long flexible tube including wall hook complete all as specified and directed. |
| 41 | S&F in repair soap dish, of stainless steel complete, all as specified & directed. |
| 42 | S&F in repair toilet paper holder, brass chromium plated fixed to walls with chromium plated (CP) brass screws complete, all as specified & directed. |
| 43 | S&F in repair CP brass overhead shower square fancy type 100x100 mm with extension CP Arm pipes. |
| 44 | S&F in repairs 22-25 mm dia stainless steel curtain rod including brackets and fancy type finials, complete, all as specified and directed. |
| 45 | Taking down eaves gutters and rain water pipes ( any size or pattern) incl all fittings , shoes, bends, swan neck etc. and removal to store |
| 46 | S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed. |
| 47 | S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 48 | S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed. |
| 49 | S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 50 | S&F 75 mm PVC (SWR) floor trap, plain with CP grating, with or without hole including jointing with solvent cement of ISI marked and approved make. |
| 51 | S&F 110mm bore PVC (SWR) bend of ISI marked and approved make any radius, complete all as specified and directed. |
| 52 | S&F 75mm bore PVC (SWR) bend, of ISI marked and approved make any radius, complete all as specified and directed. |
| 53 | S&F 100mm bore PVC (SWR) junction single (Single T) equal or unequal of ISI marked and approved make. |
| 54 | S&F 75 mm bore PVC (SWR) junction single (Single T) equal or unequal of ISI marked and approved make. |
| 55 | S&F 110mm bore PVC (SWR) vent cowl, of ISI marked and approved make complete all as specified and directed. |
| 56 | Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but n.exc 4 sqm each, complete, all as specified & directed. |
| 57 | Taking down shutters of any description exc 1.00 sqm but not exc 2.00 Sqm each and refixing in same opening after necessary easing, adjusting and repairs complete all as specified and directed. |
| 58 | S&F Factory made single extruded WPC (Wood Polymer Composite ) soild door/ window Ceostory windows & other frame / chowkhat single/double patam of size 65 x 100 mm comprising of virgin PVC polymer of 'K' value 58-60 (Supension Grade) , calcium carbonate and natural fibers (wood powder / rice husk / wheaat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabbricated with miter joints after applying PVC solvent cement and screws with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withrawal strength of 2200 N cum , (Face) & 1100 N (Edge) , minimum compressive srength of 58 N/mm², modules of elasticty 900 N/ mm² and resitance to spread of flame of class A category with property of being termite / borer proof , water / moisture proof and fire retardant. and fixied in position with MS hold fast/ lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-In-Charge.(M.S. hold fast/ lugs or SS dash fasteners shall be paid fo separately ) .Note : For WPC solid door/ window frames , minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable . Variation in profile dimension on plus side shall be accepetable but no extra payment on this account shall be made. |
| 59 | S&F Providing and fixing factory made single extruded WPC (wood polymer Composite ) soild decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of 'K' value 58-60 (suspension Grade ), calcium carbonate and natural fiber (wood powder/ rice husk / wheat husk) and non toxic additives ( maximaum toxicity index of 12 for 100 gms ) having minimum density of 650 kg/cum and screw whithrawal strenght of 1800 N (Face ) & 900 N (Edge ) , minimum compressive strength 50 N/mm² , modulus of elasticity 850 N/mm² and resistance to spread of falme of Class A category with property of being termite /borer proof , water/moisture proof and fire retardant . WPC to be laminated with PVC foil of minimum 14 microns thic of approved desing pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel but hinges of required size with necessary full body threaded star headed counter sunk S.S screws., all as per direction of Engneer-In -Charge . ( Note : Stainless steel but hinges and necessary S.S srews shall be paid seprately ) |
| 60 | Providing and fixing factory made uPVC white colour Sliding window Three track area not exceeding 2 sqm each, made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) |
| 61 | S&F aluminium powder coated door fixed on aluminium frame of section 47.62mm x 44.45x1.6 mm thick, shutter glazed with tinted glass (Modi Guard) 5mm thick fixed with rubber gasket and aluminium strips as per standard method also rubber gasket at frame so as to make air tight with cast type handle aluminium anodised of 150mm size 2 Nos (One on each side of shutter) with shutter bottom rail 150mm x 44.45mm x1.6mm thick section, middle and top rail 83.5mm x 44.45mm x 1.6 mm thick section, side style 83.5mm x 44.45mm x 1.6 mm thick section all as sper IS 737- 1986 fixed with aluminium (extruded section) hydraulic door closer egulated designation No-3 universal type and make with aluminium tower bolt arrangement of standard make with locking arrangement with 6 levers mortise lock(brass body) of size 100mm etc complete all as specified and as directed. |
| 62 | S&F 150mm size stainless steel fancy type handle, complete all as specified and directed. |
| 63 | S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified. |
| 64 | S&F 200 mm long stainless steel tower bolts of extruded section (ISI marked) complete all as specified |
| 65 | S&F 100mm double legged door stopper of stainless steel with rubber base all as specified and directed by Engr-in-charge. |
| 66 | S&F 300 mm long stainless steel sliding door bolts, fancy type, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete, all as specified. |
| 67 | S & F M.S. Framed work such as grills grating etc. with ends of bars sholdered and / or riveted into spikes, framed guard bars / railings all as directed. |
| 68 | M & L Preparation of new steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified |
| 69 | S&F peg set of 6 stainless steel fancy type,min length 600 mm all as specified & directed. |
| 70 | S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks, triple layered (cylindrical, vertical with closed top) hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe incl 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete after dismantling old RCC/PVC tank, all as specified and directed. |
| 71 | Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed |
| 72 | M&L for RCC 1:2:4 type B1 (using 20 mm graded aggrigate)as in slab,chajjas,beam etc and similar suspended works complete, all as specified and directed. |
| 73 | Form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exc 200mm thick, flat rough finished surface of concrete complete, all as specified and directed. |
| 74 | M&L for TMT bars 10mm dia and over cut to length, bent to shape required including cranking and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. |
| 75 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc. |
| 76 | Taking down existing old Exhaust fan and deposit to MES yard of any size and capacity all as directed. |
| 77 | Taking down old U/S main switches, Sheet metal enclosures DB including MCCBs, MCBs etc including making good to the disturbed surface of wall all as directed. |
| 78 | Taking down old unsv T/L of any size and capacity all as directed. |
| 79 | Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed. Please Enable Macros to View BoQ information |
| 80 | Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size all as directed. Please Enable Macros to View BoQ information |
