|
| 1 | Providing ,Supply, Installation,Testing ,Commissioning & Errection of 7.50 HP Submersible Pump of (KSB / Kalama / Kirloskar / Johnston / Cromption / BS) make conforming to BIS; 8034-1976 latest suitable for lifting clear,cold & fresh water (latest with uptodate ammendments) fitted with bronze impellers / suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- |
| 2 | Site Conditions Total Head =110.50 mtr |
| 3 | Discharge =2.5 LPS |
| 4 | Pumping Machinery = one set |
| 5 | Providing and Installation of new starters automatic pannel including auto start, auto stop and restart facility single phase preventer, timer, relay, selector switch auto and manually start stop facility, prevention of phase reversal, imbalance and overload and fixed with compatible starter complete in all respect with in all lead and lift as per satisfaction of Engineer- in-charge. |
| 6 | Providing and fixing of cast Iron double flange sluice valve of following diameter heavy duty PN-1.6 of Kirloskar / Leader Make including cost of nuts bolts rubber sheet 4mm thick entire carriage and welding of flange T-5 of both end in double end in double layerof GI Pipe testing of joints at site confirming to IS:14846 latest with upto date ammendaments complete fixing at site complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge . |
| 7 | 65 mm dia |
| 8 | Providing and fixing of C.I. double flanged swing check type reflux valve of Kirloskar / Leader make class PN 1.0 confirming to BS 5312-1984 having bye pass arrangement (to be provided on R/main side) and shall be suitable for withstanding nominal seat pressure of 16.00_ Kg/cm².complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge . 65 mm dia |
| 9 | Providing & laying suitable size copper PVC insulated armoured power 6mm square cable conforming to BIS: 1554(P-1)1988 or latest with upto date ammendments of Siemens Gloster /ICC make from meter of HPSEB to OCB & from OCB to busbar switch & starter ( one cable carrying all three phases ) including all other electrical equipment accessories such as thimbles, flexible, pipes, solder,nuts & bolts, cable glands etc. laid in pipes or tranches under floor.The type size & Make will be subject to approval of HPSEB authorities. In case of non acceptancy by HPSEB authorities it shall have to be replaced by the tenderer free of cost supply side 6mm . sq.complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge . |
| 10 | Providing & laying PVC insulated jointless, flat water proof 3 core copper cable 4.00 mm2 of Siemens/Finolex/Grandlay/Gloster make conforming to BIS:1554 (Part I)-1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge . |
| 11 | Providing and fixing MS angle & MS sheet febricated control pannel board having size 1.10 Mtrs height overall i/c two compartment of sixe 0.50 x 0.50 x 0.30 mm vertical angle frame 35 x 35 x 4mm, horizental angle 25 x 25 x 4mm, MS sheet 1.25mm thick (BG18 gauge) i/c electrical accessories Ammemeter, Voltameter ICTP switches with HRC fuse, Bus-bar chamber, MCB / OCB , 3 phase indicating lamps with toggle switches, DOL starter oil-immerressed, capacitor, overload relay etc. i/c locking arrrangments duly painted complete in all respect as per relvant code & complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge . |
| 12 | Providing & laying safty wire 6mm2 to protect the motor / Pump complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge . |
| 13 | Providing , fixing and fitting 3 - layer PP-R (Polypropylene random copolymer) pipes UV stabilized and antimicrobial fusion welded, having themal stability for hot and cold water suply including all PP-R plain and brass threaded polyproylene random fittings complete to ISI 15801-2010 and testing of joint including high steel carbon rope size 5 milimetre square for holding of submersible pump set complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge . |
| 14 | 50 milimetre dia ( PN-16) |
| 15 | Providing , fixing and fitting 3 - layer PP-R (Polypropylene random copolymer) socket complete in all respect in all leads and lifts as per the direction and Entire to the Satisfaction of Engineer in Charge |
| 16 | 50 milimetre dia . Please Enable Macros to View BoQ information |
