|
| 1 | Taking down chowkats with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n.exc 4 Sqm each and offered as credit. |
| 2 | All as per item No 1 here in before but n exc 1.5 Sqm each. |
| 3 | Taking down shutters of any description area exc 1.00 Sqm and n exc 2 Sqm each. |
| 4 | Taking down shutters of any description area n.exc 1.00 Sqm each |
| 5 | Taking down shutters of any description area exc 2 Sqm each and refixing in same opening after necessary repairs |
| 6 | Taking down shutters of any description or type area exc 1.00 Sqm and n.exc 2 sqm and refixing in same opening after necessary repairs |
| 7 | Taking down shutters of any description or type area n.exc 1.00 Sqm and refixing in same opening after necessary repairs |
| 8 | M&L for cutting holes in brick wall built in cement mortor or cement lime mortor and stone walls built in lime mortor exc half brick but not exc one brick ( Depth of embedded portion of holdfasts or lugs measured from face of jamb in to the wall) all as specified |
| 9 | Supply and fixing, factory made pressed steel frames for doors with two rebates, of size 125mm x 60mm, made out of 1.25mm thick sheet, including necessary fixing lugs, hinges, lock strike plate, etc,including back filling of PCC1:3:6 type C-2, and one shop coat of primer, complete all as specified and directed. Note: Filling holiow of frame with plain cement concrete shall be measured and paid separately. |
| 10 | Supply and fixing factory made solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing |
| 11 | S&F Mild steel work as in doors shutters,drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or wire mesh) and hanging, conforming to Fe 410-W(gde-E-250) quality A, complete all as specified and direted.Note:- MS rectangular hollow section of size 63.5 x 38 x 2.90mm shall be used for febrication of door shetter, 10mm MS sq bar for grill and MS flat 10 x 3mm shall be used for securing wire mesh with screw. Wire mesh shall be measured and paid separately. |
| 12 | S&F second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints |
| 13 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile mensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 14 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile mensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 15 | S&F for Providing and fixing factory made single extruded WPC (Wood Polymer composite) solid decorative type flush door shutter of size 30mm thick comprising of irgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal trength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 16 | S&F second class hard wood 35 mm flush shutters, solid core construction, with block board core & plywood face panels, commercial type on both sides |
| 17 | S&F second class hard wood 35 mm thick, glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain chamfered or rounded and rebated sash bars any numbers. |
| 18 | S&F second class hard wood 30mm thick, glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain chamfered or rounded and rebated sash bars any numbers. In windows and ventilators are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b) |
| 19 | S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with wooden beading or with nuts and bolts to existing steel windows/wooden windows |
| 20 | S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with wooden beading or with nuts and bolts to existing steel windows/wooden windows |
| 21 | S&F FI 25x3mm for hold fasts stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay),conforming to Fe 290 GDE E-165 |
| 22 | Preparing surface of wood & wood based materials, steel & iron work, new or old, of any description & grith, not otherwise described & treated with tar or coal tar black paint treating treating ends of posts, backs of Chowkats, etc., area tarred exc 0.1 sq.m but n exc 0.5 sq.m. each |
| 23 | Preparing surface of wood & wood based materials, steel & iron work, new or old, of any description & grith, not otherwise described & treated with tar or coal tar black paint treating small articles such as stop, covers, gully gratings, holdfasts, ends of post, backs of Chowkats, etc., area n exc 0.1 sq.m each |
| 24 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube,design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face supplying & fixing in opening including making good to the jambs as per specification all as directed.Note: The quote rate shall be inclusive of following:-(i) Existing/new wall edges shall be finished properly in cement plaster in CM 1:4 including supply and fixing of 6 Nos wooden plugs for catch door frame size not exc 17 sqcm average sectional area and 100mm long. (ii) Frame shall be fixed to the wooden plugs inserted in wall using 6 Nos of 100mm long MS Screw, 3 each on either side |
| 25 | S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 26 | S&F SS Butt hinges,100mm medium weight and fixed |
| 27 | S&F SS Butt hinges, 75mm medium weight and fixed |
| 28 | S&F extruded aluminum alloy handles,150mm fabricated type anodized |
| 29 | S&F extruded aluminium alloy handles,100mm fabricated type anodized |
| 30 | S&F Alluminium, 150mm anodized, barrel tower bolts extruded section & fixed |
| 31 | S&F Alluminium, 100mm anodized, barrel tower bolts extruded section & fixed |
| 32 | S&F Aluminium alloy, anodized, 250mm sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminium alloy & fixed |
| 33 | S&F mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 34 | S&F 150mm Floor door stopper of aluminum alloy body & single legged with hard drawn steel spring, fixed in door shutters. |
| 35 | M&L preparation of new or previously untreated wooden surfaces of any description, not otherwise described, over 10cm width or girth applying two coats synthetic enamel paint over one coat of prink primer, cmplete all as specified and directed |
| 36 | Hacking out broken glass any thickness, size, quality, from wooden frame/steel frames fixed with putty or with wooden beads. |
| 37 | S&F 4mm thick sheet glass, ordinary quality & glazing with oil putty in square n exc 0.5 sq.m in each pane |
| 38 | S&F in repairs Aluminium anodised tubular curtain rod 20mm dia with brackets. |
| 39 | S&F in repairs 18/19 MM thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with screws to timber frame work. |
| 40 | M&L 6mm thick teak wood lipping for external of 18/19 thickness of board |
| 41 | S & F 30mm Continuous (piano) hinges, mild steel, bright finish or electrogalvanised |
| 42 | S&F 100mm Hasp & staple, safety type, alluminium with mild steel hinges pin including bolt to hinges plate & fixed with screw |
| 43 | M&L Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth |
| 44 | Supplying and laying of CPVC pipes SDR 11& plain CPVC SDR 11 fittings on walls/ceiling or laying in floors of outer dia 20mmm complete complete including taking down all as specified as as specified |
| 45 | Supplying and laying of CPVC pipes SDR 11& plain CPVC SDR 11 fittings on walls/ceiling or laying in floors of outer dia 25mm complete complete including taking down all as specified as as specified |
| 46 | Supplying and layig of brass elbow of 20mm for CPVC pipe outer diamter of 16mm |
| 47 | Supplying and layig of brass elbow (3/4 X ½) of 20mm for CPVC pipe outer diamter of 16mm |
| 48 | Supplying and layig of brass Tee of 25mm for CPVC pipe outer diamter of 16mm |
| 49 | Taking up or down steel tubing and connections, including cleaning for refixing of GI water tubing of 15mm boreall as specified and directed |
| 50 | Taking up or down steel tubing and connections, including cleaning for refixing of GI water tubing of 20mm boreall as specified and directed |
| 51 | S&F PVC connections 15 mm size with PTMT nuts of length 450mm all as directed |
| 52 | S&F for grating doom 100mm dia of PTMT minimum weight 25 gms |
| 53 | S&F in repairs for 32mm dia PVC waste pipe 1000mm long for wash hand basin |
| 54 | S&F in repairs vitreous China squatting pan ‘Orissa’ pattern, size 580 x 440 mm white, integral foot rests including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor . |
| 55 | S&F in repair Vitreous China wash down water closet (pedestal pattern), white (excluding flushing cistern and flush pipe) incl Pedestal pan and trap, connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, seat cover etc, complete all as directed |
| 56 | S&F in repairs vitreous China wash basin, white, flat back, size 550x400mm incl 32mm waste fittings, brass, chromium plated for glazed ware basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed including PVC waste pipes. |
| 57 | S&F in repairs 10 liters capacity PVC low level flushing cistern complete with ISI marked body and ISI marked syphon (Make shall be Parryware Slimline or equivalent) |
| 58 | S&F in repairs 15mm fancy type chromium plated brass angle cock with flange, screwed down, high pressure, with crutch handle, screwed both ends for iron pipe or for unions and fixed |
| 59 | S&F in repairs bib cock long body with flange, fancy type brass chromium plated, screwed down, screwed for iron pipe, 15 mm bore or for brass ferrule and fixed all as specified |
| 60 | S&F in repairs pillar cock, fancy type chromium plated brass , screwed down, high pressure, with or without lettered ‘HOT’ or ‘COLD’ with long screwed shanks and fly nuts, screwed for 15 mm bore |
| 61 | S&F in repairs CP brass wall mixer 15 mm bore for mixing hot & cold water screwed down for iron pipe & fixed with provn for connection to over head shower with bend pipe |
| 62 | S&F in repairs Bath room PVC cabinet mirror of size 350mm x 450mm (Make : prayag Cat part No 551 or equivalent in Hindware/ Cera) |
| 63 | S&F in repairs bevelled edge mirror of size 600X450mm of selected quality glass mounted on 6mm thick AC building boards or on commercial plywood with aluminium beading alround and fixed to wooden plugs with CP brass screws, fixed in repairs. |
| 64 | S& F in repairs towel rail 600 mm long of CP brass fixed with and including chromiumplated brass screws and plastic cleats.(Minimm weight 190 gms) |
| 65 | S&F in repairs brass chromium plated 125mm shower roses with or without swivel joints, any size, including fixing to steel pipe or union |
| 66 | S&F sinks with drianage board made of stainless steel 0.8mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160 mm |
| 67 | Supply and fix Bib cock two way double Handle with flange, fancy type brass chromium plated,screwed down,screwed for iron pipe, 15mm bore for brass ferrule and fixed all as specified Make (Prayag- Cat Part No 8312 Or Equivalent) |
| 68 | S&F kitchen plate rack made out of stainless steel 0.8mm thick complete of size not less than 900x750x200mm, duly assembled and fixed to wall with wall screws / fasterners all as specified and directed. |
| 69 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 70 | S&F in repairs Plastic water closet seat, white, closed pattern with flat bottom, and cover and MS CP or aluminium hinging device. |
| 71 | S&F 75mm UPVC (SWR) floor trap, plain with grating incl jointing with solvent cement etc. complete. |
| 72 | S&F UPVC (SWR) pipes single socketed 75mm bore, in any length with rubber ring joints laid in trenches/floors all as specified. |
| 73 | S&F UPVC (SWR) bends 75mm bore |
| 74 | S&F UPVC (SWR) bends with access door 75mm bore |
| 75 | S&F 75 mm UPVC (SWR) branch piece, single (single Y) equal or unequal with acces door |
| 76 | S&F UPVC SWR vent cowl 75mm bore |
| 77 | S&F UPVC (SWR) pipes single socketed 110mm bore, in any length with rubber ring joints laid in trenches/floors, complete all as specified and directed.. |
| 78 | S&F UPVC (SWR) bends 110mm bore |
| 79 | S&F UPVC (SWR) bends with access door 110mm bore |
| 80 | S&F 110mm UPVC (SWR) junction single (single T) equal or unequal with acces door. |
| 81 | S&F UPVC SWR vent cowl 110mm bore |
| 82 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 83 | M&L non skid coloured ceramic tiles each tile area (sqr/rectangle) exc0.11Sqm but not exceeding 0.18 Sqm tile thickness 7 to 8 mm, in floors etc set and joined in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM 1:6 for floor finishing complete all as specified and as directed. |
| 84 | M&L coloured vitrified ceramic tiles 10mm thick light shade (square/rectangular) polished, area of each tiles n exc 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM 1:6 for floor finishing complete all as specified and as directed. |
| 85 | Material and labour for ceramic coloured tiles, Non skid, area of each tile exc 0.18sqm and not exc 0.38sqm (square / rectangle) 7 to 8mm thick mm thick, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed or bedding layer in CM 1:6 for floor finishing complete all as specified and as directed. |
| 86 | M&L 10mm thick light shade (square/rectangular) polished, area of each tiles n exc 0.36 Sqm ,as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10mm thick rendering in CM 1:3 to receive the tiles, complete all as specified and as directed. |
| 87 | Material and labour for ceramic coloured tiles, Non skid, area of each tile exc 0.18sqm and not exc 0.38sqm (square / rectangle) 7 to 8mm thick mm thick, as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match,including 10mm thick rendering in CM 1:3 to receive the tiles, complete all as specified and as directed all as specified and as directed. |
| 88 | M&L for glazed coloured ceramic tiles in vertical surfaces 300 x 450 mm 7 to 8 mm thick set & jointed in neat cement slurry & pointed in white or coloured cement to match incl 10mm thick backing coat CM 1:3 dado/skirting |
| 89 | Dismantling of existing roof treatment of any description completely and brushing the cleaned surfaces of concrete with neat cement slurry @ 3Kgs of cement per sq.m.complete all as specified and as directed. remove all the debris from site and rubbish off the premises complete |
| 90 | M&L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate over the roof slab 25mm thick, finished even and fair without using extra cement all as specied and directed. |
| 91 | M&L for 10mm thick cement plaster in CM 1:3, mixed with water proofing compound over the levelling course while the concrete is green, finished even and smooth without using extra cement all as directed.”Note : WPC shall be measured and paid separately. |
| 92 | Supply only water proofing compound |
| 93 | M&L for APP Modified prefabricated five layer water proofing membrane, not less than 3 mm thick and weighing not less than 3.00 kg/sqm reinforced with non woven polyester matt black finished over compatible, laid over a tack coat of blown bitumen 85/25 grade @ 1.20Kg/Sqm with torching the membrane on whole surface uniformly while unrolling the membrane by LPG and sealed with trowel after necessary preparation of surface, complete all as per manufactures instructions and finally finished. The Overlap joint shall be provided of 75mm in longitudinal direction and 100mm in transverse direction respectively. All the angles, abutments and the drainage outlets shall be sealed with extra care to ensure full bondage including preparatory work.Note: The work shall be carried out by authorized applicators of manufacturers |
| 94 | S&F Powder coated aluminums frame for doors,sliding windows, ventilators and with one or more rebates including joining cleat and handles and other necessary fittings for fixing etc. complete all as specified and directed. |
| 95 | S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall bepaid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screwsall complete as per architectural drawings and the directions of Engineer-in-charge all as specified complete all as specified and directed. |
| 96 | S&F in repairs 15mm fancy type chromium plated with long shank and cup concealed type angle cock with flange, screwed down, high pressure, with crutch handle, screwed both ends for iron pipe or for unions and fixed |
| 97 | S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs |
| 98 | S&F in repairs Door closer hydraulically regulated (Aluminium extruded section body), designation No. 2 universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed |
| 99 | Cleaning and removing all scale and dirt, etc, from tanks (exc 250 but n.exc 500.00 capacity in ltrs) and from mouths of circulating pipes, etc, complete all as specified and directed |
| 100 | Cleaning and removing all scale and dirt, etc, from tanks (exc 500 but n.exc 1000.00 capacity in ltrs) and from mouths of circulating pipes, etc, complete all as specified and directed. |
| 101 | S&F in repair rotational moulded polyethylene water storage tanks 500 liters capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I. Incl 25mm Nipple suitable for HDPE water tank. (minimum weight 20mm-45gms, complete all as specified including dismantiling old tank. |
| 102 | S&F in repair rotational moulded polyethylene water storage tanks 1000 liters capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I. Incl 25mm Nipple suitable for HDPE water tank. (minimum weight 20mm-45gms complete all as specified including dismantiling old tank. |
| 103 | S&F in repairs 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe & fixed.(Minimum weight 20mm-210gms. |
| 104 | S&F in repairs 25 mm bore of Gun metal globe or gate, valves with iron screwed both ends for iron pipe and fixed |
| 105 | S&F in repair Vitreous China Urinal, Half stall type size (345x320x560) coloured/white complete fixing with suitable fixing arrangements to wall with and including domed waste coupling and waste pipe complete, all as directed. |
| 106 | Dismantling of wall and ceiling board (fibre, pulp, insulation etc) or insulation board including cover fillets |
| 107 | S&F Anodised aluminium snap grid frame ( size of grid 605 x 605 mm)work for false ceiling all as specified.and in SSR part I |
| 108 | S&F 10 mm thick PVC insulation panels 600mm x600mm with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of aluminium/GI/MS as per specification, complete all as specified and directed. |
| 109 | M/L preparation of old surface of ceiling of any description and applying one coat of distemper oil emulsion ,white or tinted, complete all as specified and directed. |
| 110 | S&F 5mm thick PVC sheet fillet of width 35mm for fixed paneling inclusive of fixing fillets with screwed in side the wall to wall to make PVC Frame as per pecification and drawing. |
| 111 | S&F for solid PVC Wall Lining consisting of 5mm thick wood grain printed coloured PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing |
| 112 | S&F UPVC (SWR) pipes single socketed 110mm bore, in any length with rubber ring joints fixed to walls with stack clamp all as specified. |
| 113 | S&F UPVC (SWR) pipes single socketed 75mm bore, in any length with rubber ring jointsfixed to walls with stack clamp all as specified. Please Enable Macros to View BoQ information |
