|
| 1 | Excavation in hilly areas in all heights and depths, for crash barrier, parapets and in all kind of soil by manual/mechanical means including saturated soil comprising of pick work , jumper work , blasting work ( Both in soft and hard rock ) with chiselling/wedging out rock (where blasting is prohibited) and their intermediate classification of soil including dewatering where required, setting out true to the required lines, grades, width cutting and trimming of side slopes to level as shown in the drawing and as directed by Engineer-in-Charge at site according to the MoRD technical specification section 1600 and 300 and sorting out usefu/ unuseful materials and stacking the same in all leads, lifts in acquired width of road and transportation of un-useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus material to the approved dumping sites through all modes of transportation including head load or animal transport or mechanical means along with its levelling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and other incidentals necessary to complete the work by mechanical means and labour if required. Recovery of useful stones to the tune of 8326.64 ( Eight thousand three hundred twenty six point six four )cubic metre quantity at the rate of 300/- (Rupees Three hundred only) per cubic metre amounting to Rupees 24,97,992.00/-(twenty four Lacs ninety seven thousand nine hundred ninety two) only shall be effected from the contractor's running bills on pro-rata basis as per actual quantity executed. Any loss to the public, private property during the course of execution shall be the absolute responsibility of the contractor, which shall have to be duly compensated by him in all cases. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST. |
| 2 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification section 300 & Clause 301 as per direction of Engineer- in- charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government but excluding GST. |
| 3 | Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and parapets etcertra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiselling /wedging out rocks (Where blasting is prohibited) as per drawings and MoRD technical specification section 300 and 1600 and as per direction of the Engineer- in – Charge including setting out, Construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any leads and lifts including dressing of sides, bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150 mm (one hundred fifty milli metre) compacted thickness including shoring and strutting and pumping or bailing out water (surface and sub soil water ) upto any depth any quantum of water including cleaning of slush which may arise out during dewatering complete as per direction of Engineer-in-Charge. including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government but excluding GST. |
| 4 | Loosening of the ground upto a level of 300 (three hundred) millimetres below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 of MoRD with three wheel 80-100 (eighty to one hundred) KN (kilo newton) static roller for subgrade construction as per MoRD Technical Specifcation section 300 as per direction of Engineer- in- charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other taxes imposed by the Government but excluding GST. |
| 5 | Construction of Subgrade and Earthen Shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading by mechanical means to required slope and compacted with three wheel 80-100 (eighty to one hundred) kN (kilo newton) static roller to meet requirement of Table 300.2 complete as per MoRD Technical Specification section 300 & 1600 and as per direction of Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals. The rate is including Octroi, rRoyality, Malkana, Toll Tax, or any other Taxes imposed by the Government but excluding GST. |
| 6 | Construction of 1st (frist) layer Bio enzyme (100mm) (one hundred millimetre) thick based soil stablised layer (accredited by IRC) to a required thickness as per manufacturer design with local soil material/gravel/murram, having CBR greater than Equal to 5% (five percent) and treating it with Bio Enzyme in the ratio 1.00(One) Litre for 12.5 (Twelve point five) cum soil , spreading in uniform layer with motor grader on prepared surface. mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density complete as per technical specification including all labour, materials, like soil and metal, equipments etc. , complete, including Supervision (Supervisor shall be provided by Bio Enzyme Vendor) as per the directions of the Engineer incharge of the work . Bio Enzyme Supervisor accomodation, food and local transport will be scope of Contractor. The soil will have clay % percentage by hydrometry between 8% to 30% (Eight percent to 30% Thirty percent) . including carriage of material with in all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 7 | Construction of 2nd (second) layer Bio enzyme (75 mm) (seventy five millimetre) thick based soil stablised layer (accredited by IRC) to a required thickness as per manufacturer design with local soil material/gravel/murram, having CBR greater than Equal to 6% (six percent) and treating it with Bio enzyme in the ratio 1.00 ltr (One Litre) for 15.00 per cum (fifteen point zero per cubic metre) soil with 25% (twenty five percent) 40mm (forty millimetre) crusher broken metal (of compacted thickness) in desing mix, spreading in uniform layer with motor grader on prepared surface. mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density complete as per technical specification including all labour, materials, like soil and metal, equipments etc. , complete, including Supervision (Supervisor shall be provided by Bio enzyme Vendor) as per the directions of the Engineer incharge of the work. Bio enzyme Supervisor accomodation, food and local transport will be scope of Contractor. The soil will have clay % (percentage) by hydrometry between 8% to 30% (eight percent to thirty percent), including carriage of material with in all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 8 | Applying of curing material Terra Cure after the application of Bio enzyme layer (accredited by IRC) for by mixing Terra Cure with water in the ratio of 1:200 (one isto two hundred) and then appyling the mixed solution @ 3 ltr (at the rate three Litre) for 1.00 sqm (one square metre). including carriage of material with in all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 9 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam 100mm (one hundred millimetre) thick specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100 kN (Eighty to one Hundred kilo newton) weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per MORD Technical Specification section 400 including carriage of material within all leads, lifts and other incidentals . The rate is including Octroi, Royality, Malkana, Toll Tax or otherTaxes imposed by the Government but excluding GST. |
| 10 | Prime Coat Preparing and applying of water soluble organo silane Nano technology (for bitumen emulsion application, IRC accredited) with cationic bitumen emulsion CSSI and water <1000 (greater than one thousand)ppm TDS in the ratio of 1.00 (One) killogramme organo silane nanotechnology :100 (One killogramme) cationic bitumen emulsion CSS I.00 (one) :200(two hundred) litre water Mixing & Spraying : Take 1.00 (one ) Killogramme of organo silane nanotechnology and add in 200 (two hundred) litre water while filling water in tanker/drum and then add 100 (One hundred) cationic bitumen under circulation. Mix the solution completely .Spray the solution @1.00 (one Killogramme) per square metre on compacted surface . Rate including all materials labour hire charges of machinery etc. complete as per MoRD specifications clause 502 & direction of Engineer-in-Charge, including carriage of material with in all leads lifts and other incidental The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 11 | Tack Coat Preparing and applying of water soluble organo silane nanotechnology (for bitumen emulsion application IRC accredited with cationic bitumen CRSI and water<1000 (greater than one thousand)ppm TDS in ratio of 1.00 (one) killogramme organo silane:100 (one) killogramme cationic bitumen emulsion CRS I.00: 200 One is to two hundred) litre water .Mixing & Spraying : Take 1.40 (One point four zero) litre of organo silane nanotechnology and add in 200 (two hundred) litre water while filling water in tanker/ drum and then add 100.00 (One hundred) litre cationic bitumen emulsion under circulation. Mix the solution completely. Spray the solution @ 0.3-0.4 zero point three to zero point four) killogramme per square metre on compacted base . Rate including all materials labour hire charges of machinery etcetera complete as per MoRD specifications clause 503 & direction of Engineer –in- Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 12 | Providing, laying and rolling of close-graded Mix Seal Surfacing material of 20mm (twenty millimetres) thickness composed of 11.2 mm to 0.9 mm (eleven point two millimetre to zero point nine millimetre) (Type-A) @ 0.27 cum per 10 sqm (at the rate of zero point twenty seven cubic metre per ten square meter) aggregates using penetration grade bitumen @ (at the rate of) i.e. binders content VG-10 (viscosity Grade-ten) @ 22 kg per 10 sqm (at the rate of twenty two kilogram per ten square metre) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN (Eight to ten) Kilo Newton static roller and finishing to required level and grades as per MoRD technical specification section 500 including all leads, lifts and carriage of materials complete as per entire stisfaction of the Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 13 | Construction of Granular Sub-Base (Grade-1) by providing well graded materials, spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with wheel 80-100 kN (Eighty to one hundred kilonewton) static roller to achieve the desired density complete as per MoRD Technical Specification section 400 for grading-I Material as per the entire satisfaction and directions of Engineer – in- Charge including carriage of material within all leads, lifts and other incidentals . The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 14 | Providing, laying, spreading and compacting by mechanical means of crushed stone aggregate size 53mm to 22.4 mm (Fifty three millimetre to Twenty two point four millimetre) Grading-III [75mm (Seventy five millimetre) consolidated thickness] to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 kN (Eighty to one hundred kilonewton) static roller in stages to proper grade and camber, including applying and brooming, stone screening type-B of size 11.2mm (eleven point two millimetre) nominal size at the rate of 0.18 cum (zero point one eight cubic metre) per ten square metres and to fill up the inter stices of course aggregate, watering and compacting to the required density as per M.O.R.D. technical specification section 400 and as per the entire satisfaction and direction of Engineer -in- Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 15 | Construction of plastic cell filled cement concrete pavement, thickness as per design, over a prepared sub base, with 53(fifty three) grade Ordinary Portland Cement (OPC) or any other type as per Clause 1501.2.4 M-30 (M-thirty) Grade. Coarse and fine aggregates conforming to IS : 2386, maximum in a concrete mixer of not less then 0.2(zero point two)cubic metre capacity and appropeiate weigh batcher using approved mix design(As per IRC 44-2088, laid in approved fixed side formwork (steel channel, wedges, steel plates including levelling the fomwork as per drawing), spreading the concrete with sholvels, rakes, conpacted using needle, screed an plate vibrators and finished in continuous operation, Concrete should have a slump of 30-50mm(Thirty to fifty millimetre) with use of approved plasticizer if required. Formwork of plastic cells should be made of High Density Polyethylene (HDPE), sheets having thickness ranging from 0.20-0.22mm (Zero point two zero to zero point two two millimetre) with sides 150MMx150MM (one hundred fifty millimetre into one hundred fifty millimetre) and height as fixed by engineer in charge. Cells should be stitched using thread, thus ensuring optimum joint strength. Joint strength should be a minimum of 2.00 (two) Kilo Newton per metre. Heat welded cells should not be procured as they are not able to with stand the tension and often break when they are laid in the full width of the carriageway. Iron spikes of about 200mm (Two hundred millimetre) long are to be used to keep the cell walls taut Nylon thread or rope may be used to prevent collase of cells during placement of concrete. Iron spikes to be taken out for use in other place as soon as the concrete is in place. The subbase should be provided with concrete/stone block or brick on edge on either side of the carriageway protecting the subbase with full thickness of the concrete pavement for its confinement and protection. Curing of concrete slabs for 14 (Fourteen) days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification of cell filled Concrete Pavement Published by NRRDA ans as per the entire satisfaction and direction of Engineer –in- Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 16 | Providing and laying concrete mechanically mixed and vibrated PCC M-10 (ten) grade 1:3:6 nominal mix (one cement:three sand:six graded crushed stone aggregate 20 (twenty millimetre) nominal size ) for plain/reinforced concrete in open foundation and plinths or similar works complete as per drawings and MoRD technical specification section 800, 900, 1200 and 1600 and curing complete including the cost of form work and hauling of material within all leads, lifts as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 17 | Providing and laying concrete mechanically mixed and vibrated mix 1:4:8 ( one : cement: Four : sand: Eight : graded crushed stone aggregate 40mm (forty millimeter) nominal size) for plain/reinforced concrete in foundation and plinths or similar works complete as per drawings and MoRD technical specification section 800,900,1200 & 1600 and curing complete including the cost of form work and hauling of material within all leads and lifts as per the entire satisfaction and direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 18 | Providing and laying mechanically mixed and vibrated plain cement concrete in foundation using grade M-20 (M-Twenty) design mix with cement content not less than 350 kg (three hundred fifty kilogram) per cubic metre with 20mm (Twenty millimetres) nominal size graded crushed stone aggregate as per drawings and MoRD technical section 800,900,1200 and 1600 and curing complete including carriage of materials within all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 19 | Providing and laying mechanically mixed and vibrated reinforced cement concrete in superstructure as per drawing and MoRD technical specification section 800, 900, 1000, 1400 and 1600 using Reinforced Cement Concrete grade M-25 (M-twenty five) design mix with minimum cement contents not less than 400 kg (Four hundred kilogram) per cubic metre with 20 mm (Twenty millimetre) nominal size graded crushed stone aggregate and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab, etcetera including carriage of material within all leads, lifts and other incidental, as per the directions of the Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 20 | Coursed rubble Stone masonry (2nd sort) work in cement mortar 1:5 ( one cement : Five sand) for substructure complete as per drawings and MORD technical specification section 700,1200 &1600 complete as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 21 | Coursed rubble Stone masonry (2nd sort) work in cement mortar 1:4 ( one cement : four sand) for substructure complete as per drawings and MORD technical specification section 700, 1200 & 1600 complete as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 22 | Supplying, fitting, and placing HYSD bar reinforcement (Fe 415) in superstructure complete as per drawingand MORD technical specifications section 1000 and 1400 including hauling of materials within all leads and lifts as per entire satisfaction and direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 23 | Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 (six hundred)millimetres with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MORD technical specification sectione 1200 and as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 24 | Drainage spouts with G.I. (Galvanized Iron) pipe 100 mm (one hundred millimetre diametre) & correction resistant structural steel grating complete as per drawing and MORD technical specifications clause 1404.5 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 25 | Back filling with granular material behind abutments, wing walls, return walls and retaining walls complete as per drawing and MoRD technical specifications section 1200, 1600 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 26 | Providing and laying 100mm (One Hundred millimetre) dia (dia metre) PVC pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I (V):20(H) (One vertical : Twenty Horizontal) towards draining face complete as per drawing and MoRD technical specification section 700, 1200 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 27 | Providing and laying boulder apron laid in wire crate with 4 (four) millimetres dia GI wire confirming to IS 280 and 4826 in 100mm x 100mm (one hundred millimetre into one hundred millimetre) mesh (Woven diagonally) including 10%(ten percent) extra for laps and joints laid with stone boulders weighing not less than 40 kg (Forty Killogram) each as per drawing and MORD technical specification section 1300 including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 28 | Construction of hill side V-Shapedrain of size 0.45 x 0.25 (zero point four five into zero point two five) metre with thickness of concrete 10cm (Ten centimeter) thick M-10 ( M-Ten) grade drain in accordance with the requirement of specification true to line and grade, level and dimension and other particular as per drawing and technical specification clause 1606.1 as per direction of Engineer-in-Charge including cost of earth work in all kinds of soil and cost of form work with steel plates and carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 29 | Construction of unlined surface drains by manual/mechanical means of average cross-sectional area 0.40 (zero point four zero square metre) in soil & ordinary rock to specified lines, grades, levels and dimensions. Excavated material to be used in embankment as per MORD Technical Specification clause 307 and as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 30 | Providing and Laying of parapets with mechanically mixed and vibrated cement concrete 1:4:8 (One cement :Four Sand :Eight graded stone aggregate 40 mm (Forty millimetre) nominal size) curing complete including the cost of earth work in all kinds of soil and cost of form work with steel plates complete as per MOIRD technical specifications section 300, 800, 900, 1200 and 1600 as per direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 31 | Providing and errecting W metal beam crash barrier composing of 3 mm (three millimetre) thick corrugated sheet metal beam rail, 70 cm (seventy centimetre) above road/ ground level fixed on ISMC series channel vertical post 150 x 75 x 5 mm (one hundred fifty into seventy five into five millimetre) spacer 2.00 m (two point zero zero metre) centre to centre, 1.80 m (one point eight zero metre) high, 1.10 m (one point one zero metre) below ground road level all steel parts and filaments to be galvanized by hot dip process, a fitting to confirm to IS 1367 and IS-1364 metal beam rail to be fixed on the vertical post with spacer of channel section 150x75x5mm (one hundred fifty into seventy five into five millimetre) 330 mm (three hundred thirty millimetre) long complete as per MORTH Specification section 800 including hauling of materials within all leads and lifts as per entire satisfaction and direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 32 | Providing and fixing Ordinary Kilometer Stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 33 | Providing and fixing 200m (two hundred metre) Stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC :26 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 34 | Providing and fixing of typical PMGSY informatory sign board with logo as per MORD specification and drawing . Three MS plates of 1.6 mm (one point six millimetre) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimetres into five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimetre into twenty five milimetres into five millimetres). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimetre into seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1:2½ : 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm(Forty milimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600mm ( six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimetre into forty seven millimetres) of 12 SWG (Twelve standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and MORD technical specifications section 1700 and Annexure 1700.1 as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 35 | Providing and fixing \\"Citizen Information Boards\\" as per specifications and drawings Two MS Plates of 1.60mm thick duly welded with MS angle iron frame 25mmx25mmx5mm (twenty five millimetre into twenty five millimetre into five millimetre) on edges supported with 2Nos (two numbers) horizontal posts and vertical posts made of 75mmx75mm (seventy five millimetre into seventy five millimetre) of 125SWG (one hundred twenty five standared wire gauge) Steel tube duly embanded in and including cement concrete M-15 (M-fifteen) grade blocks of 600mm x600x750mm (six hundred millimete into six hundred millimete into seven hundred fifty millimetre), 600 mm (six hundred millimetre) below ground level. All MS will be stove enameled both side lettering and printing arrows border etc will be painted with ready synthetic enamel paint of superior quality in required shade and colur. all sections of posts and steel tube will be primer and two coats of epoxy point as per MORD technical specifications section 1700 as per direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 36 | Providing and fixing of typical PMGSY 2.00 Km (two kilometer) board as per MORD technical specification section 1700 as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 37 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5mm (one point five millimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm(seventy five millimetre into seventy five millimetre into six millimetre) firmly fixed to the ground by means of properly designed foundation with M-15 (M-fifteen) grade cement concrete 450 mm x 450 mm x 600 mm, ( four hundred fifty millimetre into four hundred fifty millimetre into six hundred millimetre), 600 mm (six hundred millimetre) below ground level as per drawings and Technical Specification section1700 and as per the directions of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. i) 900mm (Nine hundred millimetre) equilateral triangle |
| 38 | 600mm (six hundred millimetre) equilateral triangle |
| 39 | 600mm (six hundred millimetre)circular |
| 40 | 900mm (Nine hundred millimetre) octagon |
| 41 | Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2mm (Two millimetre) with area not exceeding 0.9 sqm (zero point nine square metre) supported on a mild steel single angle iron post 75x75x6mm (seventy five millimetre into seventy five millimetre into six millimetre) firmly fixed to the ground by means of property designed foundation with M-15 (M-fifteen) grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm (four hundred fifty into four hundred fifty into six hundred millimetre), 600mm ( six hundred millimetre) below ground level as per approved drawing and Technical Specification Clause 1701 and as per directions of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 42 | Providing and Fixing pavement marker (Cat eyes) made out of ABC 3 M (three) plastic of size 128x110x29.5 mm ( one hundred twenty eight into one hundred ten into twenty nine point five millimetre) without nail having 50mm ( fifty millimetres) stem of ABS The pavement marker shall be installed with epoxy ABS including carriage of materials and equipment with all mode of transportation and as per MORD specification section 1700 and as per direction of Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 43 | Supplying and installation of delineators road way indicators, hazard markers, object markers with tape, 80-100 cm (eighty to one hundred centimetre) high above ground level, painted black and white in 15 (Fifteen) centimetres wide strips, fitted with 80 x 100 mm (eighty to one hundred millimetre) rectangular or 75 mm (seventy five millmietre) diameter circular reflectorized panels at the top, buried or pressed into the ground and conforming to IRC:79 as per MORTH Specifications clause 806 & direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. dia circular reflectorised panels at the top, buried or pressed x the ground and conforming to IRC:79 as per MORTH Specifications clause 806 & direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 44 | Providing and Laying of hot applied thermoplastic compound road marking paint 2.5mm (two point five millimetre) thick with refletorizing glass beads at the rate 250 gram (two hundred fifty gram) per square metre area, thickness of 2.5mm (two point five millimetre) is exclusive of surface applied glass beads as per specificaiton and with strips of 0.10 (Zero point one zero) metre width in centre lines or edge lines of the road as per MORTH specification clause 803.4 and the directions of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 45 | Planting rooted slips of large stature grasses on slopes, including supplying clumps of appropriate grasses, splitting into slips, trimming roots, preparing lines, digging planting hole to a max of 5(five)centimetres depth with metal rod or wooden peg depending on nature of soil, planting slips at the rate of three perdrill at the specing specified, and subsequent watering (if necessary) as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 46 | Providing and laying dry rubble flooring as per drawing and MORD technical specification clause 1300 as per directions of Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 47 | Providing and laying (to level or slope) 900mm dia (nine hundred millimetres) diameter reinforced cement concrete heavy duty non pressure pipes IS (ndian Standard) Class NP-3 (Non pressue -three) for culverts on first class bedding of Granular material in single row including providing and fixing collar with cement mortar 1 : 2 ( One cement : two sand) but excluding the cost of excavation, protection works, back filling, concrete bedding and masonry work in head walls and parapets as per drawing and MORD technical specifications section 1100 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 48 | Providing and laying flooring with rubble stone in cement mortar 1:3 (one cement : three sand)laid over cement concrete bedding complete as per drawing and technical specification section 1300 as per directions of Engineer-in-Charge including curing and carriage of material within all leads, lifts and other incidentals. TThe rate is including Octroi, Royality, Malkana, Toll Tax, or any other Taxes imposed by the Government excluding GST. |
| 49 | Construction Part |
| 50 | Note: The bidder should quote his % rate (+) or (-) only on the constrcution part amount and maintenece Part -II freezed |
| 51 | Routine Maintenance after completion of construction work as per items and condition of bid document that is 4 (i) of contract data to general condition of contract and technical specification of Ministry of Rural Development roads January, 2014 (Two thousand fourteen) for rural roads including hauling/carriage of all labour equipment and materials to various location through all modes of transportation all leads, lifts to the entire satisfaction of the Engineer-in-Charge. |
| 52 | For 1st year |
| 53 | For 2nd year |
| 54 | For 3rd Year |
| 55 | For 4th Year |
| 56 | For 5th Year Please Enable Macros to View BoQ information |
