Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | SCHEDULE -A |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan),including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. a)All kinds of soil. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 5 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :a) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 6 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 7 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 8 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).Note: Mainly for gate and railing work |
| 9 | Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 4 mm thick ACP sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures. The rate includes the cost of rounding off the corners, fixing and erecting the same in position all complete as per drawings, specification and direction of the Engineer-in-charge.( Structural frame work including M.S/S.S plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). (a) Overhead informatory signage |
| 10 | Total after Correction Factor @0.973 |
| 11 | Total After Cost index @0.97 |
| 12 | Schedule – B |
| 13 | Providing and fixing \\"Air Walker\\" with the specifications below: 1. Dimensions (LxWxH): 1100 x 450 x 1300mm.2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. U-shaped main frame of NB 80mm (G.I.) \\"C\\" Class Pipe, Leg Support frame of NB 50mm (0.1) \\"C\\" Class Pipe.4. Handy frame pipes of NB 32mm (G.I.) \\"C\\" Class (NB stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80–120-micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness, UV resistant and coloured.9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.12. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.13. High tensile steel with galvanized nut bolts is used for assembly.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.15. Equipment made to G5 Mark, EN16630, DIN 79000 & 150 14001 International standard for outdoor fitness equipment.16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.17. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 14 | Providing and fixing a double\\" Sit-Up Station\\" with the below specifications: 1. Dimensions (LxWxH): 1500 x 1150 x 650mm.2. Fabricated with a main frame of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Main frame of NB 25mm (G.I.) \\"C\\" Class Pipe.4. Leg support of NB 65mm (G.I.) \\"C\\" Class Pipe ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres). 5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness.6. All pipes are powder-coated using Akzo Nobel or equivalent paint of 80-120 micron thick.7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.8. Zinc primer paint is applied at all welding points prior to finishing.9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.10. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts is used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years & maintenance cost for next 3 years @ 3% of the cost.15. This rate is inclusive of GST Charges, Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 15 | Providiind fixing \\"Air Swing\\" in pair with the below specifications.1. Dimensions (LxWxH): 1150 x 900 x 1250 mm.2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Leg Support frame of NB 50mm (G.I.) \\"C\\" Class Pipe.4. Handle support frame of NB 32mm (G.I.) \\"C\\" Class Pipe. ('NB' stands for Nominal Bore i.e., Internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high-end quality rubber grips.9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury.11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set. the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover.15. High tensile steel with galvanized nut bolts is used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 17 Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.18. This rate is inclusive of GST Charges. Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 16 | Providing and fixing \\"Horse Rider Station\\" with the specifications below:1. Dimensions (LxWxH): 1000 x 600 x 1100 mm.2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Main frame of NB 65mm (G.I.) \\"C\\" Class Pipe.4. Handle support frame of NB 50mm (G.I.) \\"C\\" Class Pipe and other pipes of 4 NB 32mm & NB 25mm (G.I.) \\"C\\" Class Pipe. ('NB' stands forNominal Bore i.e.. Internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness. UV resistant and coloured.9. Foothold made of NB 32mm (G.I.) \\"C\\" Class Pipe.10. Seat to be made up from virgin LLDPE manufactured by rotational moulding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0 60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover.15. High tensile steel with galvanized nut bolts is used for assembly.16 Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.18. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra. |
| 17 | Providing and fixing \\"Leg Press\\" in a pair with the below specifications1 Dimensions (LxWxH): 2000 x 550 x 1600 mm.2. Fabricated with main post of NB 100mm (GI) \\"C\\" Class Pipe of approved make3. Seat Main frame of NB 50mm (G1) \\"C\\" Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G1) \\"C\\" Class Pipe.('NB' stands for Nominal Bore e.. Internal Diameter of pipe in millimetres).4. All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs6. Zinc primer paint is applied at all the welding points prior to finishing.7. Baseplate cover made of virgin LLDPE plastic by rotational molding of 4.00mm thickness. UV resistant and coloured8. Foothold is made of NB 50mm (G.I) \\"C\\" Class Pipe.9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, are coloured, UV resistant and environmentally friendly.10 Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured11 The equipment must be fitted with inbuilt limiters to prevent unwanted movements.12 The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.13 Once the concrete is set, the equipment is fixed on to it and the nuts and bolts are covered with a baseplate cover.14. High tensile steel with galvanized nut bolts is used for assembly.15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.17. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra. |
| 18 | Providing and fixing \\"Pull Chair' in a pair with the below specifications:1. Dimensions (LxWxH): 2400 x 800 x 2000 mm.2. Fabricated with main post of NB 100mm (GL) \\"C\\" Class Pipe of approved make3. Seat main frame of NB 50mm (GL) \\"C\\" Class Pipe, Pipe connecting main post with handle frame of NB 65mm (GL) \\"C\\" Class Pipe.4. Handle frame of NB 32mm (G.L.) \\"C\\" Class Pipe. (\\"NB\\" stands for Nominal Bore i e.. Internal Diameter of pipe in millimetres).5 All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs7. Zinc primer paint is applied at all the welding points prior to finishing.8. Handle bars are provided with high-end quality rubber grips.9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and coloured.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly.11. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0 60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.15. High tensile steel with galvanized nut bolts is used for assembly.16 Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17 Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.18 This rate is inclusive of GST Charges. Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra |
| 19 | Providing and fixing \\"Seated Chest Press\\" in a pair with the below specifications1 Dimensions (LxWxH) 1800 x 700 x 2000 mm2 Fabricated with main post of NB 100mm (G1) \\"C\\" Class Pipe of approved make3. Seat Main frame of NB 50mm (G1) \\"C\\" Class Pipe.4. Handle frame of NB 32mm and NB 25mm (G.1.) \\"C\\" Class Pipe ('NB' stands for Nominal Bore Size i e Internal Diameter of pipe in millimetres)5. All pipes are powder-coated with 80-120 micron thick AkzoNobel or equivalent paints6 All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs7. Zinc primer paint is applied at all the welding points prior to finishing8 Handle bars are provided with high-end quality rubber grips.9. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness. UV resistant and coloured.10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly11 Maintenance-free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.12. The equipment must be fitted with inbuilt limiters to prevent unwanted movements13. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of10.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover15. High tensile steel with galvanized nut bolts is used for assembly16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years18. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra. |
| 20 | Providing and fixing an \\"Arm Wheel\\" in a pair with the below specifications:1. Dimensions (LxWxH) 850 x 800 x 1800 mm.2. Fabricated with main post of NB 100mm (G.1.) \\"C\\" Class Pipe of approved make.3. Wheel frame of NB 32mm with connecting spokes of NB 25mm. Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.1.) \\"C\\" Class Pipes ('NB' stands for Nominal Bore Size, i.e., Internal Diameter of pipe in millimetres).4. All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints.5. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.6. Zinc primer paint is applied at all the welding points prior to finishing.7. Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness. UV resistant and coloured8 Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.19 The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J shaped welded bolts of 18mm thickness.10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover11. High tensile steel with galvanized nut bolts is used for assembly12. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.13. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years14. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra. |
| 21 | Providing and fixing an \\"Elliptical exerciser\\" with the below specifications1 Dimensions (LxWxH) 1200 x 550 x 1600 mm2 Fabricated with main post of NB 100mm (G1) \\"C\\" Class Pipe of approved make3. Main frame of NB 80mm (G.I.) \\"C\\" Class Pipe.4. Handle frame of N8 32mm and NB 25mm (GI) \\"C\\" Class Pipe ('NB' stands for Nominal Bore Size ie. Internal Diameter of pipe in millimetres).5. All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints6 All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8 Handle bars are provided with high-end quality rubber grips9 Baseplate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness. UV resistant and coloured.10 Maintenance-free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured.11. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness12. Once the concrete is set the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover13. High tensile steel with galvanized nut bolts is used for assembly.14. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment15. Self-Explanatory stainless-steel label fixed on equipment for ease of use16. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury, including maintenance cost for 2 years.17. This rate is inclusive of GST Charges, Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra. |
| 22 | Providing and fixing \\"Double Cross Walker \\"with the specifications below:1. Dimensions (LxWxH) 1600 x 600 x 1600 mm.2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) \\"C\\" Class Pipe. ('NB' stands for Nominal Bore Size, ie, Internal Diameter of pipe in millimetres).4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe.5. All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints 66. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8. Baseplate cover made of virgin LLDPE plastic by rotational molding with a minimum of 4.00mm thickness. UV resistant and coloured9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.10. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and, self-lubricated are used in the equipment manufactured.11. The equipment must be fitted with inbuilt limiters to prevent unwanted movements12. The equipment is to be fixed on the ground by providing and laying Cement Concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J shaped welded bolts of 18mm thickness13. Once the concrete is set. the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover14. High tensile steel with galvanized nut bolts is used for assembly15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years17. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH Nothing shall be paid extra. |
| 23 | Providing and fixing \\"Triple Twister\\" with the specifications below1 Dimensions (LxWxH) 1300 x 1300 x 1650 mm2 Fabricated with main post of NB 100mm (GI) \\"C\\" Class Pipe of approved make3. Handle Main frame of NB 32mm (G1) \\"C\\" Class Pipe4 Handle frame spokes of NB 25mm (GI) \\"C\\" Class Pipe ('NB' stands for Nominal Bore Size re. Internal Diameter of pipe in millimetres).5 Foothold plate made of MS Sheet Metal of 3mm thickness6 All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs8 Zinc primer paint is applied at all the welding points prior to finishing9. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured10 The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0 60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness11. Once the concrete is set, the equipment is fixed on to it12 High tensile steel with galvanized nut bolts is used for assembly13 Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14 Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years.15. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra |
| 24 | Providing and fixing a \\"Rowing Machine\\" with the below specifications1 Dimensions (LxWxH) 1250 x 800 x 1150 mm2 Fabricated with main post of NB 100mm (GI) \\"C\\" Class Pipe of approved make.3 Main frame of NB 65mm (G.I.) \\"C\\" Class Pipe4. Handle support frame of NB 25mm (G.I.) \\"C\\" Class Pipe. ('NB' stands for Nominal Bore Size ie, Internal Diameter of pipe in millimetres).5 All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints6 All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8 Baseplate cover made of virgin LLDPE plastic by rotational molding of 4.00mm thickness. UV resistant and coloured.19 Foothold made of NB 50mm (GI) \\"C\\" Class Pipe10 Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, coloured, UV resistant and environmentally friendly11 Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured12 The equipment must be fitted with inbuilt limiters to prevent unwanted movements.13 The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 10 60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.14 Once the concrete is set. the equipment is fixed on to it and nuts and bolts are covered with a baseplate cover.15 High tensile steel with galvanized nut bolts is used for assembly.16. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment17. Self-Explanatory stainless-steel label fixed on equipment for ease of use, including maintenance cost for 2 years18. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH Nothing shall be paid extra. |
| 25 | Providing and fixing a \\"Stair Stepper with Twister\\" with the below specifications.1 Dimensions (LxWxH): 1000 x 800 x 1400 mm2. Fabricated with main post of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make ('NB' stands for Nominal Bore i e.. Internal Diameter of pipe in millimetres).3. Twister main frame of NB 32mm (G.I.) \\"C\\" Class Pipe and Handle frame of NB 32mm (G.1.) \\"C\\" Class Pipe. Twister Foothold plate made of MS Sheet Metal of 3mm thickness.4. Stepper main frame of MS pipe 96 x 46mm and Handle frame of NB 32mm & 25mm (G.I.) \\"C\\" Class Pipe.5 All pipes are powder-coated with 80-120-micron thick AkzoNobel or equivalent paints.6. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.7. Zinc primer paint is applied at all the welding points prior to finishing.8 Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury.9. Maintenance-free bearings of SKF or equivalent make duly oil-sealed and self-lubricated are used in the equipment manufactured.10. The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts is used for assembly.13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless-steel label fixed on equipment for ease of use.15. The equipment must be fitted with inbuilt limiters to prevent unwanted movements.16. Baseplate cover made of virgin LLDPE plastic by rotational molding of 4.00mm thickness, UV resistant and coloured including maintenance cost for 2 years.17. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra.\ |
| 26 | Providing and fixing an \\"Exercising Bar\\" with the below specifications:1. Dimensions (LxWxH): 1800 x 550 x 1500mm.2. Fabricated with a main frame of NB 100mm (G.I.) \\"C\\" Class Pipe of approved make.3. Main frame of NB 32mm (G.I.) \\"C\\" Class Pipe.4. Leg support of NB 65mm (G.I.) \\"C\\" Class Pipe ('NB' stands for Nominal Bore i.e.. Internal Diameter of pipe in millimetres).5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness.6. All pipes are powder coated using Akzo Nobel or equivalent paint of 80-120 microns thick.7. All joints of pipe are MIG welded with joints scalloped as necessary and dressed off, removing sharp edges and burrs.8. Zinc primer paint is applied at all welding points prior to finishing9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness. UV resistant and coloured.10 The equipment is to be fixed on the ground by providing and laying cement concrete with a minimum size of block to be constructed of 0.60 mtr x 0.60 mtr x 0.60 mtr (Payment for CC to be used in fixing of equipment shall be done separately) and J-shaped welded bolts of 18mm thickness.11. Once the concrete is set. the equipment is fixed on to it.12 High tensile steel with galvanized nut bolts is used for assembly13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless-steel label fixed on equipment for ease of use. including maintenance cost for 2 years.15. Pipe and sheet components should be cut by at least 2KW laser machine having CNC made components welded using robot with at least 2 metre welding range16. This rate is inclusive of GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra. |
| 27 | Providing and fixing a \\"Weight Assisted Shoulder Press\\" with the below specificationsWeight Assisted Shoulder Press of minimum size 1350x1600x1150mm fabricated with main post of G.I 'C' Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. C Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing Handle support frame made of GI 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4 00 mm, colourful and UV resistant and environmental friendly Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF /equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement All open ends of pipe to be closed by Gl/LLDPE caps or sealed in for user safety The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete Equipment made to GS Mark. EN 16630. DIN 79000. ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment Self-Explanatory stainless steel label shall be fixed on equipment for ease of use Pipe and sheet components should be cut by at least 2 KW laser machine having CNC made components welded using robot with at least 2 metre welding range. Cost of earth work and concrete in foundation to be paid for separately. This rate is inclusive of maintenance cost for 2 years as well as GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra |
| 28 | Providing and fixing a \\"Weight Assisted Chest Press\\" with the below specifications:Weight Assisted Chest Press of minimum size 1100x1500x1300mm fabricated with main post of G.I.C Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. C Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of Gl 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by Gl/LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN 16630. DIN 79000. ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by at least 2 KW laser machine having CNC made components welded using robot with at least 2 metre welding range. Cost of earth work and concrete in foundation to be paid for separately. This rate is inclusive of maintenance cost for 2 years as well as GST Charges. Transportation Charges, Fixing Charges and CPOH. Nothing shall be paid extra. |
| 29 | Providing and fixing a \\"Weight Assisted Lat Pull Down\\" with the below specifications:Providing, designing and fixing of Weight Assisted Lat Pull Down of minimum size 1200x1300x1650mm fabricated with main post of G I. C Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. C Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates Plates have to be fully locked in the machine but movable for the adjustment Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4 00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN 16630. DIN 79000. ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by at least 2 KW laser machine having CNC made components welded using robot with at least 2 metre welding range Cost of earth work and concrete in foundation to be paid for separately This rate is inclusive of maintenance cost for 2 years as well as GST Charges. Transportation Charges. Fixing Charges and CPOH Nothing shall be paid extra. |
| 30 | Providing and fixing a \\"Weight Assisted Rowing Machine\\" with the below specificationsWeight Assisted Rowing Machine of minimum size 1500x1450x1650mm fabricated with main post of G.I. C' Class of NB 65 mm and other support and handle frames of NB 50 mm G.I. C' Class pipes only Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI 'C' Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs Chest support to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-20 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to GS Mark, EN 16630. DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by at least 2 KW laser machine having CNC made components welded using robot with at least 2 metres welding range Cost of earth work and concrete in foundation to be paid for separately This rate is inclusive of maintenance cost for 2 years as well as GST Charges. Transportation Charges. Fixing Charges and CPOH. Nothing shall be paid extra. |
| 31 | Regular maintenance for three years(after free maintenance for 2 years) of all the Gym equipment 18 Nos, installed at each location in DDA parks as per schedule B consists of the following:-a) Replacement/repair of parts of equipment in case of theft/vandalism.b) Check and set right/replacement for worn bearings, misaligned moving points, adjust/tighten loose parts, covers, seats, foundation and flooring.c) Tightening nuts/bolts/screws i/e welding of various parts/joints of equipment wherever required.d) Calibration of Instrument every three months.e) Priming coat & painting coat, if required.f) Lubrication/oiling every 15 days.g) Inspect and adjustment of drive, timing and running belts.h) Replacement of damaged parts & rectification of any other defects observed as per the direction of the Engineer-in-charge. except:i. Due to Force majeure orii. Abnormally bad weather, serious loss or damage by fire oriii. Damage due to the act of god oriv. Any other cause which is in the absolute discretion of the Engineer-in-charge is beyond the contractor's control. |
| 32 | Schedule – C |
| 33 | Maintenance cost for 5 years of newly installed open gym equipments |
| 34 | Free maintenance for first two years after installation of open gym equipments |
| 35 | For 3rd year item No.9 to 26 of schedule 'B' |
| 36 | For 4th year item No.9 to 26 of schedule 'B' |
| 37 | For 5th year item No.9 to 26 of schedule 'B' Terms and Conditions: 1. The agency shall regularly inspect and upkeep the equipment in proper working condition as required.2. Any complaint, as and when reported, shall be attended within 03 days during the 05 years maintenance period. Failing which, a penalty of ₹2,000/- per day shall be imposed and recovered from the agency.3. In case the equipment or its parts are stolen during the execution to negligence in maintenance by the agency, the agency shall replace the stolen equipment/parts at its own cost. No payment shall be made for such replacement.4. The Performance Guarantee submitted by the agency shall be released only after recording of the Final Completion Certificate, i.e.. after successful completion of the full 05 years maintenance period.5. Provisional Completion shall be recorded separately by the competent authority for: Replacement & refurbishment of equipment, and Maintenance of refurbished equipment. However, the Final Completion Certificate shall be recorded only after the successful completion of the full 05 years maintenance period.6. The Security Deposit @ 2.5% of the gross amount of each running bill and final bill. deducted until it amounts to 2.5% of the tendered amount, shall be released only after recording of the Final Completion Certificate (i.e., after successful completion of the 05 years maintenance period).7. An amount equal to 50% cost of replaced equipment shall be withheld from each R/A bill, in addition to the Security Deposit, towards warranty. This withheld amount shall be released proportionately. year- wise, after successful completion of each year of the 05 years maintenance period (including both free and paid maintenance periods) as mentioned in the table provided below :- First Year 10%Second Year 10%Third Year 10%Fourth Year 10%Fifth Year 10% Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
