Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Removal of plants / ficus grown by pulling out root system embedded in masnory, cutting stem and application of high/gur/lime formulation as specified by the Architect or other patented chemical biocide treatment such as biocide 'Glycel' (iso proplamine salt of glyphosate) or other chemical as specified by the Engineer in charge etc. complete. |
| 2 | Clearing grass and removal of rubbish upto a distance of 50 metres outside the periphery of the area. |
| 3 | Dismantling the existing lights, tublelight, bulbs, fans, independent plug points, wiring including circuit mains of all types along with accessories etc. complete as per specification No.WG-DM / PW. |
| 4 | Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/ structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40 mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:-(1) The elevational area of the scaffolding shall be measured for payment purpose.(2) The payment will be made once only for execution of all items for such works. |
| 5 | Providing and fixing Jute Kantan (Tarat) screen to the scaffold-ing for external guniting as directed including removing the same after the work is over etc. complete. |
| 6 | Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 metres or spreading in the compound and cleaning the site etc. complete. |
| 7 | Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering including disposal of rubbish to the dumping ground within 50 metres lead. |
| 8 | Removing brick bat coba including stacking the spoils as directed with all leads, lifts etc, complete.. |
| 9 | Removing planking from roof or ceiling and stacking them as directed with all leads and lifts etc. complete. |
| 10 | Removing wooden or A.C. partition including frame work and stack-ing the materials as with all leads, lifts etc. complete. |
| 11 | Removing cement tiles or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all lead, lifts, etc. complete. |
| 12 | Removing lime or lean cement concrete including stacking the spoils as directed with all leads, lifts etc, complete |
| 13 | Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete. |
| 14 | Removing G.I. or A.C. sheet roofing including purlins, principal rafters etc. including sorting service able and unserviceable materials, stacking the same as and where directed in the compound including scaffolding etc. complete. |
| 15 | Removing iron pipe railing having wooden or R.C.C or C.C or iron posts and stacking the materials as directed etc. complete. |
| 16 | Removing purlins from roof including stacking as directed with all leads , lifts etc. complete. |
| 17 | Removing rafters from roof including the materials as directed with all leads, lifts etc. complete. |
| 18 | Removing battens from roof and stacking them as directed with all leads and lifts etc. complete. |
| 19 | Removing King Post truss from roof and stacking the materials as directed with all leads and lifts etc. complets |
| 20 | Removing R.S. girders of any size and span lowering the same and stacking neatly wherever directed in the compound scaffolding etc. complete. |
| 21 | Removing chockes and leakages from down take G.I/CI/PVC pipe line on walls floor level by using zoola / scaffolding and rectify the same for functioning with all lifts etc. complete. |
| 22 | Removing corrosion of steel reinforcement by mechanical means like wire brushing, chipping to remove loose rust and then applying rust removal solution by using brush application, leaving the surface for at least 15 to 30 minutes, then removing loose materials by scrubbing or with brush. After detachment of loose scales reddish rusted surface is still left exposed, this has to be retreated or as per approved manufacturers specifications. (Note:- Consider surface area of concrete for payment) |
| 23 | Dismantling brick masonary in lime or cement mortar and stacking the materials as directed with all lead, lifts, etc |
| 24 | Dismantling stone masonary in lime or cement mortar including stacking the materials as directed with all lead, lifts, etc.. |
| 25 | Shifting ( heavy stone) architectural fragments from 50 to 100 m distance by male mazdoors (heavy) with all necessary equipment, tools etc, and stacking it in appropriate location as directed by the Conservation architect within the premises complete. |
| 26 | Lowering down the debris obtained from breaking and removing the cement lime plaster/ burnt brick masonary of the first floor by any means without causing dust nuisance and damage to structure, stacking the same as and where directed including cleaning the site complete. |
| 27 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means |
| 28 | Excavation for foundation in hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete (lift upto 1.50 m) By Manual Means. |
| 29 | Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. |
| 30 | Providing and laying cast in situ 1:2:4 Lime Concrete of trap/ granite/ quartzite/ gneiss metal for foundation and bedding as per detailed specifications and drawings or as directed including bailing out water, centring, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required with fine aggregate, preparing the lime mortar in lime miller and then mixing with coursed aggregate in drum mixer as per specifications including bailing out water, watering etc. complete. |
| 31 | Filling in plinth and floors with approved excavated material in 15 cm . To 20 cm. layers including watering and compacting etc. complete. |
| 32 | Conveying the excavated materials, debris of brick or stone masonary, R.C.C. slab, water proofing, stone members/ materials, cement/ lime concrete, tiles/ marbles/ stone slab/ brick bat coba, etc. upto 5 km, away from the site and cleaning the site properly. |
| 33 | Gently cleaning the surface of stone masonary and piers with specialized water misting techniques employing air water jet using a fine nozzle sprinkling system caliberated to spray fine mist along the stone surface without over wetting followed up by gentle brushing with soft nylon brushes and removing dirt, dust, bird dropping, grease, oil, algae, fungus, monkey beats, vegetation growth etc. as specified. Gentle surface cleaning may include using water misting and mild pH balanced surfactants as specified for indicated areas to remove the surface dirt, grit, accretions by means of water misting and cleaning etc. complete as directed by the Engineer in charge. |
| 34 | Application of water, oil and stain repellent, breathable, Chlorophyllin based Protectguard MG of Killickguard or equivalent with brush on Stone Façade in two coats. Applications to be done |
| 35 | Repair with Polymer Modified Mortar (PMM): Repairs to the deteriorated / damaged areas of RCC elements in the structure shall be carried out by using powder Polymer Modified repair mortar. The polymer modified mortar is applied when the epoxy bonding coat is still tacky. In one application25 mm thickness shall be built. Subsequentlayer shall be built with one bond coat of Polymer modified cement slurry. The polymer modified repair mortar shall be mixed, applied and cured as per technical |
| 36 | Providing general pest control services to the building to control the nuisance of cockroaches, lizards, pin bores and other insects etc. with 4 operations in a year and monthly check up. |
| 37 | Providing anti termite treatment to the sides of flooring of the existing building as per I.S. 6313 (Part-III) by punching holes 6 mm dia. drilled at a distance of 30 cm. centre to centre and injecting one percent of chlorodane emulsion concentrate at the rate of 50 ml per hole and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. |
| 38 | Providing antitermite treatment to the wooden frames of doors /windows of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at four corners on one side and four corners on other side at a downward angle of about 45 degree at the junction of wood work and masonary and injecting150ml. of chlorodane 5% W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. |
| 39 | Providing antitermite treatment to the joints of wooden beams / joist used for the roof work of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at a downward angle of about 45 degree at the junction of wood work and masonary and injecting 80ml. of chlorodane 5%W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper. |
| 40 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. |
| 41 | Providing & mixing Bipolar Concrete Penetrating Corrosion Inhibiting Admixture to provide corrosion protection to both anodic and cathodic sites on the steels surface in fresh concrete |
| 42 | Pollysheet for pollyhouse - 200 Micron |
| 43 | Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted / bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. |
| 44 | Providing structural steel work in hollow section of various thickness and sizes in square, rectanular and round shape from 25mm to 450mm section as per IS 4923 YST 310 Grade produced from iron ore and blast furnace route etc. as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/bolted/ welded connections and painting complete. |
| 45 | Providing and laying Rough Shahabad Stone Flooring 50mm to 60mm thick and of required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning etc. etc. complete. |
| 46 | Teakwood in Structural members : Providing and fixing Ist quality (Superior Quality- Berma) Teakwood in structural members like beams, columns, joist, rafters, purlins, purlin cleats, hip rafters, jack rafters, ridges, wall plates, post plates and posts, pedestals or any other wooden members etc. including removing damage/decayed wood members,fixing stainless steel screws, cutting, sawing,making proper wood jonery, scaffolding if necessary all iron work and applying one coat of primer or as directed by Enginner Incharge etc. complete For wood size T.W beams and Stringer beams of size beam - 0.20 x 0.10 - upto 5 m (7.87 x 4 inch x 17ft) “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 47 | Teakwood in Structural members : Providing and fixing Ist quality (Superior Quality- Berma) Teakwood in structural members like beams, columns, joist, rafters, purlins, purlin cleats, hip rafters, jack rafters, ridges, wall plates, post plates and posts, pedestals or any other wooden members etc. including removing damage/decayed wood members,fixing stainless steel screws, cutting, sawing,making proper wood jonery, scaffolding if necessary all iron work and applying one coat of primer or as directed by Enginner Incharge etc. complete For wood size = T.W Battens of size (0.025 x 0.025 (1 x 1 inch) thick length 3 m )“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 48 | Providing and fixing Mangalore tiled roofing with class 'AA' tiles including securing the last course of tiles near the eaves with steel flat 40 mm x 3 mm and 1.22 mm wire fixing country teak wood sloping battens of 25 x 12 mm teak wood horizontal battens of 50mm x 25mm over the slopping battens, all iron work and coal tarring the battens etc. complete (Excluding ridge and hip tiles). |
| 49 | Providing and fixing Mangalore tile ridge and hip tiles of class 'AA' including scaffolding if necessary, pointing with coloured cement mortar and curing etc. complete. |
| 50 | Teakwood planks in kadipat ceiling, wall cladding,flooring : Providing and fixing Ist quality (Superior Quality) Teakwood planks in kadipat ceiling, wall cladding,flooring or any other wooden members etc. TOUNGH AND GROOVE STYLE including removing damage/decayed wood members,fixing stainless steel screws, cutting, sawing,making groove, making rounding on edges if required, making proper wood jonery, scaffolding if necessary all iron work and applying one coat of primer or as directed by Enginner Incharge etc. complete For wood size = 5\\" x 1.5\\" to 7\\" x 1.5\\", 50 mm.(1½″) thick Teak Wood Flooring or Planking“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 51 | Providing and fixing Teak wood Eaves Board 15 cm.(6″) wide and 12.5 mm. (½″) thick, as per detailed specifications and drawings or as directed including the planks to be best Moulmein teak to be 12.5 mm. (½″) thick and 15 cm.(6″) in width, of a uniform colour and planed, the planks to be laid truly parallel to the floor so as to cover the end rows of the tiling and to be fixed with screws of the proper length driven countersunk, all joints to be neat and close, scaffolding etc. complete. “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 52 | Providing and fixing country teak wood barge board 22 cm wide and 20mm thick plain type including scaffolding and painting in two coats etc. complete“ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 53 | Providing and fixing colour coated Zincalume (R) AZ150 (min 150 gms/ sq.mt. total on each side) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45mm Base Metal Thickness (BMT) (0.5mmTCT), Hi-strength steel with min.550 MPa yield strength, metallic hot dipcoated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND (R) steel quality super durable polyester paintcoat (within organic pigment). The paint shall have a total coating thickness of nominal 35um, comprising of nominal 25um exterior coat on top surface and nominal 10um reverse coat on back surface. Profile sheet shall have nom. 950-1050mm effective cover width and nominal 25-30mm deep ribs with subtle square fluting in the five pan at nominal 180-250mm center-to-center. The end rib shall be designed for anti-capillary groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25um Zinc-Tin alloy coated, Hexhead, self-drilling screw etc. complete. (weight of profile 4.52 Kilogram/ One Square Metre) |
| 54 | Providing and fixing plain zinc sheeting of 0.80 mm thick (22 B.W.G.) over the ridge hip or valley to galvanized iron sheet roofing including all fastening and bolt galvanised iron screws and bolts, lead and bitumen washers etc. complete.(Weight of 6.8 Kilogram/sq.m.). |
| 55 | Flashing: Flashing will be provided in desired girths (0-600mm Girth) as per the requirement. Flashing will be factory formed out of the 0.5mm TCT Colour coated Galvalume Sheet and supplied in 2500mm length MEASUREMENT AII the roofing shall be recorded jointly from top of the ridge to the eaves and from side to side including covered by flashing. Make of Sheets: Lloyd Standing Seam/Lysaght Flex-Lok/Kingzip SF R.A. Unit : 1 / square Metre |
| 56 | Providing and laying Hyperplas standard or equivalent polymeric multiple monolithic five layer water proofing flexible, pliable and high tensile strength membrane (3 Kilogram/ One Square Metre) & consist of centre core of 90 micron thick High Molecular High density Polyethylene film (HMHDPE) which is protected on both the side with polymeric mix. Applying the membrane by thermofusing to roof & parapet after applying thin film of hot blown bitumen 85/25 or 90/15 grade @ 1.2 Kilogram/ One Square Metre maximum as per surface condition or Hyperplas primer @ 250 gms/ One Square Metre as per site condition on the surface to be treated with 10 cm overlapping including finishing etc. complete and covering guarantee of 7 years on stamp paper of Rs. 100/- and as directed by Engineer-in-charge. (Prior permission of S.E.in writing is necessary before inclusion of this item in estimate). |
| 57 | Providing and fixing 10 MM Multiwall Polycarbonate sheet at any height including scaffolding. |
| 58 | Galvanised iron sheet 1 mm (20 B.W.G.) eaves precoated gutter 200 mm to 230 mm wide and 100 mm to 125 mm deep moulded or half round girth upto 600mm including iron rods, on the edges (throughout the length) and galvanised iron sheet ferrules with fixtures, for outlets wherever required clamped using W.I. clamp 38 mm x 3 mm fixed 1.0 m C/C including making necessary connections with rain water pipes etc complete and as directed. |
| 59 | Supplying and Fixing 100 mm internal dia. 4.0 mm thk. (weight approx. 10.0 Kg./Rm.) centrifugally cast C. I. pipes Confirming to IS 3989, sockets spigots type pipe for rain water/soil waste and ventilation with all fittings including scffolding, 1 : 1 CM jointing proper embedding and fixing on wall & column etc complete as directed. |
| 60 | Building (Bd-R : Rofing and ceiling)Turbo ventilator 24'' |
| 61 | Providing Ashlar Fine Masonry of Sandstone in lime mortar 1:1 for Walls, Parapet as per the site requirement of size of stone [0.45 x 0.35 x 0.30 Meter] (18\\" x 14\\" x 12\\") as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 62 | Providing Semi-octagonal Coping Cut-stone Second Sort, 20 cm. (8″) height and 45 cm. (1ꞌ6″) wide of sandstone in lime mortar 1:1½ with size of stone [0.60 x 0.60 x 0.20 Meter] as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, the stone shall be dressed full or to template, exposed face of the stones shall be fine rough tooled, semi-circular and all joints shall be in line and close and not more than 3 mm. (⅛″) thick, preparing the lime mortar in lime miller, scaffolding, watering and all coping work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 63 | Providing Ashlar Fine Masonry of sandstone in lime mortar 1:1 for Brackets as per the site requirement of size of stone [0.60 x 0.45 x 0.35 Meter] as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 64 | Providing Ashlar Fine Masonry of sandstone in lime mortar 1:1 for Talkhada as per the site requirement of size of stone [0.45 x 0.45 x 0.20 Meter] as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 65 | Providing Ashlar Fine Masonry of Sandstone in lime mortar 1:1 for Stirng courses as per the site requirement of size of stone [0.60 x 0.45 x 0.35 Meter] as per detailed specifications and drawings or as directed including the stones be of approved quality, colour, hard and free from defect of any kind, dressing every stones fine tooled on all beds, joints and faces, full true if the surface are plane or to uniform curves or twists if required, the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course not less than 30 cm. (12″) in height averaging 4½ c. ft., the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 66 | Providing Ashlar Arching of Sandstone stones in lime mortar 1:1, with size of stone 0.60 x 0.45 x 0.45 (24 x 18 x 18\\") as per detailed specifications and drawings or as directed including the arch stones be of approved quality, colour, hard and free from defect of any kind, the arch stones in all cases of the entire thickness, the arch stones shall be dressed full and true to their proper shapes with the necessary summering, twist or winding and be set in fine mortar, the intrados, joints and beds to fairtooled and left full, the cast or keying course to be accurately fitted, at all horizontal joints the intrados to have a 2 cm. (¾″) chamfer, the face stone may be tooled or rock-faced with or without chamfer as directed, in arches up to 60 cm. (2ꞌ) in depth all stones shall be of the full thickness of the ring, arches to be built on proper centring, the bed joints shall be radial and the side joints shall be at right angles to the bed joints and the thickness of the joints shall not exceed 5 mm. (3/16″) preparing the lime mortar in lime miller, cantering/scaffolding, watering and all arch work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 67 | Providing/Re-setting Ashlar Fine Masonry of reuse-stones in lime mortar 1:1 in superstructure as per detailed specifications and drawings or as directed including the stones shall be set in fine mortar, the beds or joints being in no case more than 3 mm. (⅛″), the stone shall be laid in regular course, the face stone shall be laid header and stretcher alternately, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 68 | Making of moulding/ grooving/ chamfering on the surface of the formed stone member, as per given design or drawing, by an expert, artisan craftsman, including light sand papering of the finished member if required. |
| 69 | Making of relief architectural carving on the surface of the formed stone member, as per given design or drawing, by an expert, artisan craftsman, including light sand papering of the finished member if required. |
| 70 | Dutchman repairs of stone sections that severely distressed, reinstallation of new Black basalt stone piece to match existing stone as a fascia of minimum 75mm depth of similar colour and texture and size. The size of the stone piece would be approx. of 150 x 300mm. The fixing of the new stone would employ mortar grout and anchoring technique after neatly cutting out damaged stone profile using one of the following tehnniques : a) Stainless steel pins of 6mm dia threaded at end. b) Helifix treatment |
| 71 | Providing and fixing Ductile iron Man Hole Covers/ Strom Water Grating and Grating with frame of Various sizes, weight and types and load bearing capacity as per EN-124, equivalent NECO with prior approval of concerned Superitending Engineer. |
| 72 | Providing, fabricating M.S. ornamental railing of simple geometrical design weighing as specified below with country teak wood moulded hand rail 10 cm x 5 cm with winders and newel posts complete if required with 3 coats of french polish or synthetic enamal paint, fixing the M.S. railing securely in floor, wall etc. as directed by Engineer In Charge. (Weight 10kg to 15kg per sqmt) |
| 73 | Providing and fixing teak wood railing of 1.05 m height in the interior of the museum for specific areas as per detailed drawings with top and bottom rails of size 0.075 x 0.15m and balusters of 0.05 x 0.05m, each supported by the vertical newel posts of 0.075 x 0.15 x 1.05 m with newel cap of size 0.1 x 0.1m as directed by the Engineer, removing the existing railing members and fixtures, including french polishing, and hardwares and joinery etc. complete. (Note: The work to be executed on preapproval of conservation architect). |
| 74 | Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 75 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork, cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 76 | Providing and laying Cast in situ/ Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, coverblocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 77 | Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 78 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. |
| 79 | Providing Brick Masonry First Class in superstructure with size of brick 0.223 x 0.150 x 0.075 (9\\" x 41/2\\" x 2 1/2\\") in lime mortar 1:1½, as per detailed specifications and drawings or as directed including the bricks to be of uniform size, moulded ground, thoroughly well burnt and sound, ringing clearly when stuck with trowel, the bricks to be soaked in water for 12 hours before used, the bricks are to be laid flush in mortar in such bond as directed, as far as possible, bricks of uniform colour are to be selected for the face work when it is not to be plastered, the joints are not to exceed 12.5 mm. (½″), no bats or half brick to be used in the work, racking out joints where pointing or plastering to be done, striking joints where no pointing or plastering is to be done, preparing the lime mortar in lime miller, scaffolding, watering and all masonry work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 80 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete |
| 81 | Providing Soil Bag Support to the monument with contractor´s soil in proper layers carefully as directed by Engineer in-charge including filling, tying and conveying the bags, removing the soil bags after work up to a distance of 50 meter beyond the monument area and cleaning the site etc. complete. |
| 82 | Providing and fixing frame work of galvanised iron for suspended false ceiling which includes galvanised iron perimeter channels of size 27 mm and 0.5 mm thick having one flange of 20 mm and another of 30 mm along with perimeter of the ceiling, fixing in brick wall / partition with the help of rawal plugs and screws, suspending galvenised iron intermediate channels of size 45 mm and 0.9 mm thick with two flanges of 15 mm each from the soffit at 1200 mm centers with steel galvanised iron hanger of width 25 mm x 0.5 mm fasteners, ceiling section of 0.5 mm thickness having curved wedge of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 450 mm centers, 12.5 mm dry walls screws at 230 mm centers; fixing screws mechanically either with screw driver or drilling machine with suitable attachment etc. complete. |
| 83 | Providing and fixing false ceiling of 10 to 12 mm thick decorative boards of fibrous plaster of paris including scaffolding if necessary all architectural work like mouldings, cornices, coves, domes, cups as per detailed drawings and three coats of spray painting to boards etc. complete. (excluding frame work, runners and mild steel suspenders) |
| 84 | Crack Stitching 8mm Helibar Providing and fixing of Helifix Hi-fin reinforcement Helibars of 8mm dia, single bar in one slot, MOC Austenitic stainless steel, ASTM 304, having cross section area of 10.5sqmm, pitch 38/40, with ultimate tensile strength not less than 1370 N/sqmm, shear strength 7.2kN, along with Helibond Grout, a special cementitious grout with low expansion, non gassing and injectable with exceptional non shrink thixotropic properties having compressive strength at 28 days of not less than 45 N/sqmm. Including chasing of slot in mortar bed upto a depth of 40mm for HeliBars, cleaning the dust and debris from the slot, making damp with water to achieve good bonding of HeliBar with HeliBond grout in the groove of brick/stone masonry ensuring that it remains tight at the joint after curing, including all tools, tackles and equipments using specified machines, excluding Staging & Scaffolding, at various places where there is crack in brick/ stone/ block masonry as directed by structural engineer in charge/ Helifix. |
| 85 | Creating HeliBeam using two 6mm Helibars Providing and fixing of Helifix Hi-fin reinforcement Helibars of 6mm dia, two bars in one slot, MOC Austenitic stainless steel, ASTM 304, having cross section area of 8sqmm, pitch 29/30, with ultimate tensile strength not less than 980 N/sqmm, shear strength 5.5 kN of single bar, along with Helibond grout, a special cementitious grout with low expansion, non gassing and injectable with exceptional non shrink thixotropic properties having compressive strength at 28 days of not less than 45 N/sqmm. Including chasing of slot in mortar bed upto a depth of 50mm for HeliBars, cleaning the dust and debris from the slot, making damp with water to achieve good bonding of HeliBar with HeliBond grout in the groove of brick/stone masonry ensuring that it remains tight at the joint after curing, including all tools, tackles and equipments using specified machines, excluding Staging & Scaffolding, at various places where there is crack in brick/ stone/ block masonry as directed by structural engineer in charge/ Helifix. |
| 86 | Pinning with cemTie 8mm (SS 304) Providing and fixing of Helifix Hi-Fin reinforcement Helical pins / CemTies of 8mm dia. and specified length into a predrilled hole of not more than 18mm dia. MOC Austenitic Stainless Steel ASTM-304, having cross-section area of 10.5sqmm having helical pitch of 38/48 with ultimate tensile strength not less than 1370N/sqmm along with Helibond grout, a special cementitious grout with low expansion, non gassing and injectable with non shrink thixotropic properties having compressive strength at 28 days of minimum 45N/sqmm and specified length along with Helibond grout. Including drilling of holes for CemTies upto 15 mm more than the specified depth, cleaning the dust and debris from the hole and making damp with water ensuring to achieve good bonding of CemTie with HeliBond in the holes of masonry ensuring that it remains tight after curing, at locations as per instructions provided by structural Engineer in charge/ Helifix, including all tools tackles and equipments using specified machines, excluding Staging & Scaffolding. |
| 87 | Resitie 8mm: Providing and Installing of Helifix make special purpose remedial ties with resin i.e.ResiTies having 8mm Dia and specified length. MOC. austenitic stainless steel as per ASTM304, having cross section area of 10.5mm², pitch 38/40, with UTS13.7KN having pointed ends. Clean out all dust from heslot by pneumetic spoil cleaner prior to grouting and fixing in position of the ResiTie using Helifix make PolyPlus SF Resin, a special purpose styrene free polyester resin having cherecteristic tensile load of 43.3kN, is to be used to bond the stainless steel Hi-fin reinforcement ties with the help of manual pressure gun to be injected in he drilled out hole of masonry, ensuring that it remains tight in the joint after setting as directed by structural engineer/Helifix. All above excluding staging/scaffolding |
| 88 | Sock Fix Anchor M10 (SS304) - Providing & fixing mechanical grouted sock anchor system for bonding stone/ brick masonry as specified by structure engineer/ Helifix design including drilling upto 32 mm dia and depth 25 mm more than the required length of the anchor.The 10 mm dia stainless steel grade 304 threaded bar with UTS of 750 N/mm2, Ultimate Tensile Load of 40KN,0.2%Proof Load of 450 N/mm2 and C.S.A of 58.0 mm2, encased with a specially designed sock allowing itself to inflate when the grout is pressure filled, until the grout bleeds out of the sock micro mesh so that the sock balloons itself into the voids around the drilled hole, thus creating a chemically grouted mechanical anchor.The grout should be specially formulated cementitious Portland cement mix having compressive strength of 65N/mm2 at 28Days. Grouting should be done with a pressure pot maintaining 3 to 4 bar pressure during the installation. The installer must as certain that the sock must inflate to its full capacity into the pre-drilled holes complete as per directionof structural engineer / Helifix. All above excluding steel staging & scaffolding, as per site conditions wherever necessary. |
| 89 | CrackBond TE 250 Providing & fixing of CrackBond TE 250ml an injectable special purpose non shrink thixotropic epoxy resin with the help of manual pressure applicator and nozzle, including opening of crack, cleaning and ensuring sealing of cracks of 2mm - 12mm width upto a maximum depth of 150mm. |
| 90 | Polyplus SF Providing and filling of general purpose styrene free resin with the help of manual pressure applicator and nozzle, to be used for anchoring helical bars wherever needed/ specified by structural engineerin charge/ Helifix. |
| 91 | Providing and fixing Indian teak wood Solid doors flat arched type with double leaf shutter with frame of 50 x 50 mm, Door frame of 80 x 100 mm, inlcuding solid planks fixed in postion as per drawings and details provided by conservation architect, including bidding pattis, brass and iron fixtures and fastenings and finishing the wood work with oil painting 3 coats etc. complete “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 92 | Providing and fixing Indian teak wood fully Solid flush doors with double leaf shutter made with solid planks of 30 - 32 mm thick, arched door frame of 80 x 100 mm, glass in arched profile above the door shutter, inlcuding solid planks fixed in postion as per drawings and details provided by conservation architect, including bidding pattis, brass and iron fixtures and fastenings and finishing the wood work with oil painting 3 coats etc. complete “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 93 | Providing and fixing Indian teak wood fully Glazed doors with four shutter made with wooden frame of 50 x 60 mm thick, arched door frame of 80 x 100 mm,inlcuding glass fixed in postion as per drawings and details provided by conservation architect, including bidding pattis, brass and iron fixtures and fastenings and finishing the wood work with oil painting 3 coats etc. complete “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 94 | Providing and fixing Indian teak wood Partly Glazed and Partly solid doors with double leaf+ shutter with wooden frame of 50 x 50 mm thick, arched door frame of 60 x 100 mm, lower half of the shutter to be solid and upper half to be glazed, inlcuding glass and planks fixed in postion as per drawings and details provided by conservation architect, including bidding pattis, brass and iron fixtures and fastenings and finishing the wood work with oil painting 3 coats etc. complete “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 95 | Providing and fixing Indian teak wood glazed windows arched type with double leaf shutter with frame of 60 x 75 mm, window frame of 80 x 100 mm, inlcuding toughened glass 6 mm thick fixed in postion as per drawings and details provided by conservation architect, including bidding pattis, brass and iron fixtures and fastenings and finishing the wood work with oil painting 3 coats etc. complete “ It is mandatory to use well seasoned and first quality Indian Teak Wood from the Forest Department’s FDCML.” |
| 96 | Providing and applying melamine polish of required finish to the wood work by spray machine including knotting and preparing the even surface by scraping, applying French polish, scaffolding if required etc. complete |
| 97 | Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12 mm with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position and clear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983) |
| 98 | Providing and fixing M.S. grill door 24 Kilogram/ One Square Metre of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etc |
| 99 | Providing and fixing in position after hoisting, precast 1:2 cement mortar reinforced jali 80 mm thick with 3 mm diameter mild steel bar reinforcement, of approved design on both sides, fixing in cement mortar 1:3 and curing etc .complete. |
| 100 | Providing and fixing Invisible railing in the specified location with metal frame as directed by conservation architect |
| 101 | Providing pigeon net with 1\\" square mesh complete with installation. Installation kit includes SS hooks. |
| 102 | Providing and fixing of SS 304 - Polycarbonate Base Bird Spike with necessary fittings and scaffolding at any height, Including cleaning the existing Surface if necessary or as directed by Engineer In charge etc. complete. |
| 103 | Building (Bd-T : Doors and windows)Mosquito proof Nylone net |
| 104 | Glass mosaic tile : Providing and fixing glass mosaic tile .(Fixing in gray cement and filling joint with white cement) PALADIO / PINO /ELIMENT |
| 105 | Providing and fixing tiles equivalent to Bharat Tiles of plain colour laid in a combination of one or more colours as per the design indicated by the Architect & grinding edges filling joints as per manufacturer's specifications and including bedding mortar, grouting, watering, curing, cleaning, polishing etc. complete as directed by the Architect. |
| 106 | Providing and fixing Pattern tiles of 23- 25mm thick Bharat Tiles or equivalent of approved colours and cut to shape of approved patterns & grinding edges filling joints as per manufacturer's specifications and including 25 mm thick bedding mortar, grouting, watering, curing, cleaning, polishing etc. complete as directed by the Architect. |
| 107 | Providing and fixing in place 25mm thick and 138 mm wide solid WPC (wood polymer composite) planks of 1st Generation or Equivelant on railing with sizes shown in Architectural Drawing including necessary harware for fixing , drilling etc . all complete with necessary respective provisions up to the level of satisfaction of Architect / Engineer in charge |
| 108 | Providing and applying antifungal self leveling 3mm EPU system including coving at floor wall junction, necessary surface preparation by cleaning and de-dusting. The System shall be executed in three stages, firstly by applying a solvent free epoxy primer which has a volumetric ratio of mixing @ 200 microns dft, then laying 1.8mm self leveling epoxy based screed and finally applying a solvent free EPU (epoxy polyurethane), self leveling coating to yield a dft of 1000 microns. The EPU coating shall be a two component with volumetric ratio of mixing. No fillers shall be added at the site while laying the self leveling EPU including Aisle or zone marking in different colours etc. complete as per manufacturers specifications and as directed & approved by Engineer In-Charge. |
| 109 | Providing and laying in situ cement concrete M20 with tremix treatment for 100 mm thickness for flooring with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumen etc. complete. |
| 110 | Providing and laying Polished Kota stone flooring With Hand-Cut Polished Kota Stones 25mm to 30mm thick and required width in plain/diamond pattern on bed of 1:6 Cement mortar including cement float, filling joints with neat cement slurry, curing, cleaning and Mirror Polishing etc. complete Note- Water absorption for kota stone should not exceed 0.05%.( Item to be used with prior permission of Superintending Engineer ) |
| 111 | Providing leather finished polishing to Kota / Marble / Shahabad / Kadappa Stone slab by continuous grinding in 4 coats of different bits to receive rough and matty finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. |
| 112 | Supply of hand finish top machine cut, 3 line dressing Cobble Stone in size: 100 x 100 x 100mm in Approved colour to be fixed on prepared sub-base with cement mortar 1:4 40mm thick and cement slurry ,filling of joints in C.M. 1:2 with grey cement to match the colour of cobble stone in the required pattern, design and as directed by the Engineer incharge, including cleaning, curing etc. complete as specified and as directed by the engineer |
| 113 | Providing and fixing in place 300mm x 300mm x 3mm polyurethane stick on tactile directional tiles and warning tiles having beveled edges and of the approved brand, make and colour and conforming to ISO 23599: 2012 inside the building on all floors in corridors, lobbies , level differences as per accessibility standards and to be installed as per the installation instructions given by the manufacturer using butyl rubber adhesive and the hardware specified by the manufacturer, as per the direction of the engineer in charge complete. |
| 114 | Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 60 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete |
| 115 | Providing and laying cast in situ 1:1:4 Lime Concrete of broken brick metal for coping or waterproofing as per detailed specifications and drawings or as directed including centring, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required, with fine aggregate, preparing the lime mortar in lime miller and then mixing with coursed aggregate or surkhi in drum mixer, the concrete must be bitten for two days with pouring water as per specifications, scaffolding, watering and all concrete work when handed over to be perfectly clean and free from all mortar stains, etc. complete. |
| 116 | Providing injection grouting with a slurry of lime and fine screened sand in proportion 1 : 1 with a proper pressurized jet pump, including cleaning, washing and packing the exisitng cracks or holes in the brick or stone masonry properly upwards with the slurry, scaffolding, curing etc. complete |
| 117 | Providing Lime Pointing to stone work in lime mortar 1:1 in superstructure, as per detailed specifications and drawings or as directed including all face or visible work shall be pointed, unless otherwise specified and shall be done while the mortar is fresh, the mortar shall consists of lime and fine sand shall not be ground fine but sand should be finer, the joints of the pointed work shall be neatly defined by the pointing, the lines shall be regular and uniform in breadth and the joints shall be raised or flat as may directed, preparing the lime mortar with 640 gram pulp of wood apple (Belfruit) per cubic metre of lime mortar as a bonding material, scaffolding, watering and all work when handed over to be perfectly clean and free from all mortar stains etc. complete |
| 118 | Providing 12 mm. thick Rough Cast Lime Plaster in single coat in lime mortar 1½:1 in superstructure, as per detailed specifications and drawings or as directed including all joints in masonry and brick work are to be racked out to a depth of at least 20 mm. and the wall to be washed with fresh water and thoroughly wetted for six hours before plastering, the plaster to be applied in an even and uniform coat well pressed in to the joints and to be well beaten for 1½ days with hand tappers, the plaster should also be well sprinkle during the proses of beating with a mixture of 1.10 kg jaggary and 640 gram pulp of wood apple (Belfruit) in 90 to 135 litre of water, the plaster being wetted occasionally with fresh water while the beating is in progress, all exposed angles and junctions with door frame to be carefully finished, all mouldings shall be worked true to template and drawn neat, clean and level, soffits of arches must true arch of circle, preparing the lime mortar in lime miller with 1.60 kg Gugal (a kind of fragrant gum) and 960 gram chopped hemp (fibre of bhendi or tag ) per cubic metre of lime mortar as a bonding material, of lime as a bonding material, scaffolding, watering and all work when handed over to be perfectly clean and free from all mortar stains etc. complete. |
| 119 | Stucco work in lime, surkhi and sand (1:1:1) as per traditional practices and design, the mortar should be prepared by grinding mill only. The thickness varies from 10mm to 100mm as per design. |
| 120 | Providing and applying integral fine coat, with addition of colour pigments, as paint to the plain lime stucco plaster in 2 layers, including scaffolding, curing, all leads and lifts, etc. complete. 1) The first coat to be laid is a mixture of fine lime and white washing lime in proportion of 2:1,made smooth with wooden rubbers and very lightly beaten. 2)The finishing coat consisting of fine lime, white washing lime, mixed with the appropriate pigment in 1:2:1 proportion is to be applied and well polished with trowels. |
| 121 | Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. |
| 122 | Providing and applying gypsum plaster (with Gypsum material )with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface /or on newly brick surface (Excluding rough cast plaster )in all position including preparing and Finishing the surface scaffolding etc.complete. |
| 123 | Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. |
| 124 | Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist. |
| 125 | Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc.complete. |
| 126 | Providing and applying synthetic enamel paint or flat oil paint in any requiered shade in 3 coats over a primer coat as per manufacturers specifications including scrapping, cleaning the surface etc. Complete. |
| 127 | Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. |
| 128 | RWH - Shallow Percolation Pit providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast RCC rings, 300mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge |
| 129 | RWH - Recharge PitProviding and constructing recharge pit of 2.0m deep and 1.0m dia of pre-cast RCC rings with 6.5\\" dia x 25m deep borewell at the floor of recharge pit including installation of combination of solid/perforated PVC casing pipe wrapped around with netlon mesh including 300mm thick sidefilling around outside of RCC rings (annular space) with 40mm size boulders including filling of recharge pit up to 0.5m depth with 25-75mm clean washed gravels from bottom up followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) including netlon mesh between each gravel/fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) media layer including covering with RCC slab, manhole frame & cover, PVC rungs, PVC end-caps, fittings etc. including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing.The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge. |
| 130 | GARDEN SOIL: Supplying on site garden soil well sieved 90% to pass through I.S. Sieve of 10 mm size free from stones rubbish like dried grass roots and other such materials. The soil should be fresh from quarry.The color of the soil generally be red. The soil will be measuring box. (farma) (Item includes Royalty charges, transporting, loading, unloading etc.) lead charges for 20KM is considered |
| 131 | FARM YARD MANURE: Supplying on site well decayed, well dried, well powedered, without clods and free from stone, dried grass and other rubbish material. The color of manure generally be black. The Manure will be measuring box. (farma) (Item includes Royalty charges, transporting, loading, unloading etc.) lead charges for 20KM is considered |
| 132 | Preparing Shrubbery : Excavating the ground to a required depth of 30 cms. Removing rubbish and Conveying unwanted stuff to a required distance as directed. Filling fresh garden soil and manure in excavated area in 3:1 proporstion to a height of 30 cms. Mixing garden soil and manure thoroughly well, leveling, watering on previous night. Planting well developed shrub plants. 0.5 m height, 0.45 mt. apart as directed and maintaining till well established by watering, weedings, stirring replacing, replacing casualatie etc. complete. Following Species to be Included in shrubbery : A) Kaner, B) Spider Lily c) Rose plant d) Mogra e) Tagar f) Singonium (Red), g) Hemigraphics h) Zebrina Pendula i) lajalu j) Spotipaylam k) Heliconia l) Alpenia m) Refiss Palm n) Cycus Palm |
| 133 | Preparing Ground cover : Excavating the ground to a required depth of 20 cms. Removing rubbish and Conveying unwanted stuff to a required distance as directed. Filling fresh garden soil and manure in excavated area in 3:1 proporstion to a height of 20 cms. Mixing garden soil and manure thoroughly well, leveling, watering on previous night. Planting suitable ground covers as directed in staggering pattern distance between two rows 25cm, watering and maintaining till well established : a) Singonium (Red), b) Hemigraphics c) Zebrina Pendula d) lajalu e) Spotipaylam f) Heliconia g) Alpenia h) Refiss Palm i) Cycus Palm |
| 134 | Maintenance of garden in all respect for keeping gardening in good condition such as weeding, cleaning, watering, cutting, gap filling, manuaring, cutting, and composting and preparation of bed plantation, trees, shrubs, flowerbed with toilet washing and cleaning for a 9 month (Garden area 5400 sq m) |
| 135 | Double Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 900mmD Providing and fixing Double Faced Mobile Unit for Compactor 2150mmH x 2745mmW x 900mmD - BASE FRAME : Base Frame shall be fabricated in channel Type from minimum 2.5 mm thick MS Sheet Size of Channel 25mm x 100mm x 45mm. GUIDE RAILS : The guide rails shall be made out of 28mm Bright bar placed on 1.2 mm thick M.S. Plate which will be above the floor and are as per the international standard of safety. SUPER STRUCTURE : Super structure of the Mobile storage system will consist of knock down type panels. All the components such as shelves, front panel, end panel, vertical rear panel, central partition etc. Will act as an integral member of the Unit. SHELVES : Shelves made of 22SWG thick Prime Quality C.R.C.A. having 10 folds each will be provided each designed to carry a U.D.L. of 70 Kilograms. VERTICAL PANEL : Vertical panel consists of the front, Centre & rear panel shall be made out of 20SWG thick C.R.C.A. Prime quality Mild Steel & designed to take the load of shelves. DRIVE COVER PANEL : Made out of 22SWG thick C. R.C. A. prime quality Steel to cover the entire drive mechanism. CENTRE PARTITION : The Centre partition will comprise of a full C.R.C.A. prime quality Mild Steel 22SWG Sheet. LOCKING : System will be provided with individual rack locking as well as centralised locking arrangement on the last unit when all units are brought together, central lock when operated gets locked with the floor & does not allow access to the units. DRIVE MECHANISM : Driving Mechanism will be provided externally supported on special grade anti-friction bearing to have smooth & effortless movement. Entire mechanism or gear & sprockets shall be incorporated within the front panel provided in the front of the unit within an area of 1000mm x 200mm x 60mm. DRIVING WHEEL : Fully Powder Coated three pronged drive wheel for better torque & free movement of the rack over the guide rail. INDEXING ARRANGEMENT : Acrylic card holders provided on the front panel for easy identification & retrieval. FINAL FINISH : Powder Coating (8 tanks process with 70 microns). |
| 136 | Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With PVC accessories on wall /ceiling as per specification No: WG-MA/CON. |
| 137 | Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With PVC accessories on wall /ceiling as per specification No: WG-MA/CON. |
| 138 | Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 139 | Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 140 | Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete. |
| 141 | Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete. |
| 142 | Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete |
| 143 | Supplying and erecting modular type 3 pin 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete |
| 144 | Supplying, erecting, testing and commissioning of 6kVA capacity online pure sine wave with backup time of 1 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input and 3 phase output complete with all protections as per specification no. AP-UPS |
| 145 | Supplying, erecting, testing and commissioning of 20kVA capacity online pure sine wave with backup time of 1 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input and 3 phase output complete with all protections as per specification no. AP-UPS |
| 146 | Supplying and erecting 12V/100Ah SMF battery with battery terminal wire, duly charged with 24 months warranty complete. |
| 147 | Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 148 | Supplying & erecting triple pole and neutral distribution board (TPNDB),SPMCB of 8 ways /phase (24 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB |
| 149 | Supplying, fixing and commissioning 4 pole RCBO 63A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO |
| 150 | Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware. |
| 151 | Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware. |
| 152 | Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 300 mm width & 20 mm height complete with necessary hardware |
| 153 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 35 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 154 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 155 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 156 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 157 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 158 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU |
| 159 | Supplying and laying (including excavation of suitable width & depth up to 90 cm) 120 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. |
| 160 | Supplying and laying (including excavation of suitable width & depth up to 90 cm) 200 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. |
| 161 | Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI |
| 162 | Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP. |
| 163 | Supplying and erecting Copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP. |
| 164 | Supplying, erecting, testing and commissioning of diesel generating set with alternator of 160 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 27.8 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0m, provided with first filling of oil, diesel not less than 290 Ltr etc. on provided M20 Grade CC Foundation as per specification no. GEN-DG |
| 165 | Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 140 kVA up to 180 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF. |
| 166 | Making cement concrete foundation in 1:2:4 cement concrete with foundation bolts and nuts complete. (cost of wooden box is included) (for DG Set). |
| 167 | SITC of ESE type Lightning Arrestor Air Terminal as per standard NFC 17-102, Level IV with protection radius 51 mtr @ mounting height 5 meter. LA should be have CPRI test cerficate and should have test cerficate as per NFC 17-102 of suitable europian authority. |
| 168 | SITC of 3 meter height Mounting structure MAST (FRP/G.I.), along with supporting guy rope, base plate, mounting structure, required nut bolts etc. |
| 169 | SITC of Strike Recorder with weather proof Enclousure. It should be standalone type with no external power source requirement. |
| 170 | SITC of Test Link |
| 171 | SITC of Pipe in Pipe type GI maintanance free earthing - 80/38 (3.0 Mtr.s) with all other loose acessories and earthing pit chamber and cover. |
| 172 | SITC of single core 35 Sq. MM. Insulated Alm. Armoured Cable along with all installation accessories like clamp etc. (Optional) from LA to Earth Pit. Manufacturer to specify Copper/Aluminium). |
| 173 | Supplying, fixing and commissioning of MLTP including: Incoming - 200A MCCB 25 KA-2 nos, 200A ATS 4P - 1 Nos, Bus 300A Aluminium Outgoing : 63A 4P MCB - 6 Nos, 40A 4P MCB - 4 Nos, 25A 4P MCB - 0 Nos, 25A DP MCB - 4 Nos with floor mount stand |
| 174 | Providing & erecting hot dipped galvanised Raceway with cover manufactured from 16 SWG (1.6 mm thick) GI sheet of 200 mm width & 50 mm height complete with necessary coupler plates & hardware. |
| 175 | Providing & erecting hot dipped galvanised Raceway with cover manufactured from 16 SWG (1.6 mm thick) GI sheet of 100 mm width & 50 mm height complete with necessary coupler plates & hardware. |
| 176 | Providing & erecting hot dipped galvanised junction box manufactured from 18 SWG (1.2 mm thick) GI sheet of 200 mm x 200 mm complete with necessary cover plates & hardware. |
| 177 | Providing & erecting hot dipped galvanised junction box manufactured from 18 SWG (1.2 mm thick) GI sheet of 300 mm x 300 mm complete with necessary cover plates & hardware. |
| 178 | Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. withnecessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. |
| 179 | Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500mm) as per specification No. WG-NAS/RAK |
| 180 | Supplying and erecting 3m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete |
| 181 | Supplying and installing FR PVC sheathed HDPE insulated copper cat-6 cable Suitable for networking as per specification no. WG-ELVC/NC |
| 182 | Supplying and fixing 1 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC |
| 183 | Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC. |
| 184 | Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP |
| 185 | Supplying and fixing SC/LC type multimode duplex adapter to couple two connectors between OFC & Fibre switch/Fibre module as per specification no. WG-NAS/MMA |
| 186 | Supplying, fixing, and configuring 24-ports 1 G unmanaged gigabit POE switch erected in provided rack complete. |
| 187 | Supply and Installation of 5MP PoE IP Bullet Camera with automatic varifocal lens from 3.3 to 10 mm lens and 30 meter inbuilt IR, Dual Streams with configurable bit rate, GOP and frame rate, Edge based Video Analytics- object classification (Human/Vehicle), object in field, line crossing, enter field, leave field, loitering, follow route, objects stopping or starting to move, counting, occupancy, condition change, similarity search, 16 number of analytics/rules can be configured simulaneously. The video analytics software can detect up to 64 objects per frame in real time. support memory card up to 2TB capacity with health monitoring for early service indication. The recording in local storage should also be AES encrypted, support ONVIF S,G,T,M with MQTT event forwarding, onboard data security by using TPM (Trusted Platform Module) and PKI, supports TLS 1.3, Secure boot, Signed Firmware, software sealing to notify of device configuration changes, Embedded Login Firewall to minimize DDOS Attack, X.509 v3 digital certificates with SHA516 signature hash, audit logs, Unsecure ports like HTTP and RTSP are disabled by default, uses RTSPS/SRTP for video streaming, UL 2900-2-3 Level 2 cybersecurity certified, Camera should have UL, EN, CE, FCC, NDAA, with IP 66 and IK10 impact protection |
| 188 | Supply and Installation of 5MP Outdoor Dome camera with 1/2.9‑inch CMOS, Effective pixels 3072 (H) x 1944 (V), 30fps, Sensitivity – (3100K, reflectivity 89%, 1/25, F1.3, 30IRE)Color 0.24 lx Mono 0.03 lx With IR 0.0 lx, 120 dB Dynamic range, Electronic Day/Night, Automatic Electronic Shutter (AES), H.265, H.264 MP (Main Profile); M-JPEG Video compression, White balance, Backlight Compensation, Privacy Mask,Rule based alarms and tracking, Line crossing, Enter /leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking based on Duration, Size, Aspect ratio v/h, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), Audio detection (if microphone used), 3 to 10 mm Automatic Varifocal (AVF) lens, MicroSD card slot for edge recording, Motion, tamper and audio detection(if microphone used), FTP, IR range upto 30mtrs Dropbox and e-mail applications, 3 axis adjustment, ONVIF Profile S & G & T, PoE, IP66 and NEMA 4X, IK10, CE, FCC , UL certified. SD card support up to 2TB. |
| 189 | Supply and Installation of 12MP IR Panoramic camera with 1/2.3‑inch CMOS, 360° lens, Effective Pixels 3008 x 3008 (9 MP), 1 to 25 [30] fps, Sensitivity @30IRE: 0.15lux(color), 0.048lux(mono); 0 lux with IR; 20m IR; 120 dB WDR, Video compression H.264 (MP)/ H.265 (MP); M- JPEG, Electronic Day/Night, White Balance, Automatic Electronic Shutter, Backlight compensation, Intelligent Dynamic Noise Reduction (iDNR), Privacy Masking, Rule based alarms and tracking, Line crossing, Enter /leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), Camera Trainer (machine learning to train user specified objects), Built-in microphone(Integrated array with 3 digital MEMS audio sensors), Signal-to-Noise Ratio, Full-duplex / half duplex Audio Streaming, Memory card slot, 10/100 Base-T, ONVIF Profile S,G, M & T, clientside/cameraedge dewarping,IP66, NEMA 4X, IK10, PoE, CE,UL, FCC. |
| 190 | Supply and Installation of all-in-one recording, viewing and management solution for network surveillance systems for up to 256 channels, Pre-installed, pre-configured IP storage solution, with RAID-5/RAID-6 protected, Dedicated storage operating system delivers robust , secure operation, Hot-swappable hard drives, Advanced user and alarm management,Intel® Core™ i7-12700E (25 MB Intel® Smart Cache 2.10 GHz) Processor,16 GB DDR5,ECC UDIMM memory installed, 2U rack mount, 12 Trays: 3.5- inch SATA 3; max 24TB per HDD slot maximum supported, 12Gb/s SAS RAID Card, 4 USB ports; Intel onboard graphics (Intel® UHD Graphics 770),Microsoft Windows Server IoT 2022 for storage standard,UL, CE Certified. 2 x RJ45 Gigabit Ethernet LAN ports (teamed); 1 IPMI BMC port. Operating temperature (°C) 0°-40°C; Operating relative humidity, noncondensing (%) 8 - 90%. Video Managment software In-built (Server-client architecture) with Live viewing of multiple cameras, Local recording and snapshots, PTZ control and digital zoom, Playback and export from storage, Motion and forensic search, Multi-screen grid selection , Sequencing selection, favorite view design.Dual authorization login,e Map support,ONVIF profile S,T complied,User management,Alarm management,SQL based database,LDAP support.Support of camera edge based analytics/server based analytics alarm triggering. Certifications UL,CB,CE,FCC,NDAA,BIS |
| 191 | Supplying & erecting 55\\" professional LED display with 1920 *1080 ( Full HD) Display, suitable for 32/64 channel NVR and following features Brightness: minimum 500 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In,Built-in speakers maximum 10 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON |
| 192 | Supply and Installation of Client Workstation with 21 Inch Monitor, HP Z2 Tower G9 Workstation i7-12700 12C 2.10 / 64GB (4x16GB) DDR5 4800 ECC / 512GB M.2 SSD + 1 TB SATA / NVIDIA T1000 8GB 4mDP / DVD RW / 500W / Win 11 DG Win 10 / 5/5/5 With Monitor / Display |
| 193 | Supplying & erecting of Burglar Alarm:- 12V power supply, type of sensor used glass break, or magnetic contact sensors , receives signals from sensors, processes the information, and determines when to trigger the alarm,Selectable 4 channel beam frequencies,4 step LED indicator, D.Q. circuit,Lightning and surge protection,Anti-frost hood cover Adjustable beam interruption time |
| 194 | Supplying & erecting of Motion Sensor:- 12V power supply, type of sensor used Entrans or Exit sensors , receives signals from sensors, processes the information, and determines when to trigger the alarm, LED indicator, D.Q. circuit,Lightning and surge protection,Anti-frost hood cover Adjustable beam interruption time |
| 195 | Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With PVC accessories on wall /ceiling as per specification No: WG-MA/CON. |
| 196 | Supplying, erecting, testing and commissioning 15 to 30 Watts sound column or ceiling mounted complete as per specification no. FF-PA/SOC |
| 197 | Supplying, erecting, testing and commissioning stand mounted / handheld type wired microphone having 2 mV/Pa sensitivity, impedance level limit 300 ohms and 50 - 16000 Hz suitable to operate in -10 deg C to +55 deg C with min. 7 metre shielded cable and 3 Pin Professional XLR Connector, stereo jack complete as per specification no. FF-PA/MIC |
| 198 | Supplying, erecting, testing and commissioning of 1.5 sq. mm speaker wire complete. |
| 199 | RE-2AS Supply of EN 54-16 certified and EN 60849 standards, public address and voice alarm system that ensures a fast, safe and controlled emergency evacuation. It should have 2 class D 500W amplifiers, one shall be for the feild output with two configurations for 100V/70V lines and another one is as standby backup, 6 zones, 3 audio inputs, 6x6 audio matrix,Digital Signal Processing Based Voice Alarm Controller and LCD display 2 rows x 16 characters with 3 inputs. It should have the provition for battery installation with proper rigit & safe mounting option. It shall be suitable for both Wall or Rack mounting provision and have following features:- 1. Support Up to 8 MPS-8Z multizone micropohones or VAP-1 panels connected with CAT5 UTP cable 2. Digital Amplifier (inbuilt) 2X500 watts and 6 zones,Backup amplifier included . 3. 4 pre-amp outputs for external PAamplifiers connection. 4. 10 minutes storage for pre-recorded messag. 5. USB connectivity. 6. Password protection, 7. Overriding Facility for Emergency Condition. 8. Have In-Built or attached MIC. 9. Work on 100 - 240V~ 50/60Hz and standby battery 1x 12VDC. 10.FireAlarm Control Panel integration. 11. Interface MODBUS RTU RS 485 Half duplex Supply of EN 54-16 certified and EN 60849 standards, public address and voice alarm system that ensures a fast, safe and controlled emergency evacuation. It should have 2 class D 500W amplifiers, one shall be for the feild output with two configurations for 100V/70V lines and another one is as standby backup, 6 zones, 3 audio inputs, 6x6 audio matrix,Digital Signal Processing Based Voice Alarm Controller and LCD display 2 rows x 16 characters with 3 inputs. It should have the provition for battery installation with proper rigit & safe mounting option. It shall be suitable for both Wall or Rack mounting provision and have following features:- 1. Support Up to 8 MPS-8Z multizone micropohones or VAP-1 panels connected with CAT5 UTP cable 2. Digital Amplifier (inbuilt) 2X500 watts and 6 zones,Backup amplifier included . 3. 4 pre-amp outputs for external PAamplifiers connection. 4. 10 minutes storage for pre-recorded messag. 5. USB connectivity. 6. Password protection, 7. Overriding Facility for Emergency Condition. 8. Have In-Built or attached MIC. 9. Work on 100 - 240V~ 50/60Hz and standby battery 1x 12VDC. 10.FireAlarm Control Panel integration. 11. Interface MODBUS RTU RS 485 Half duplex |
| 200 | RE-2AS MPE Expansion unit model RE-2AS MPE for the paging microphone RE-2AS MP8Z. It has 8 software programmable buttons for paging up to 8 public address zones. It has an iron chassis to provide stability and protection against damages. All buttons are designed for an intensive use. Expansion unit model RE-2AS MPE for the paging microphone RE-2AS MP8Z. It has 8 software programmable buttons for paging up to 8 public address zones. It has an iron chassis to provide stability and protection against damages. All buttons are designed for an intensive use. |
| 201 | Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7TR to 2.00TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position in provided recess with wooden frame complete specification no. AP-AC/WAC |
| 202 | Supplying, erecting, testing and commissioning of 20HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control piping range upto 1000 metre operation in cooling mode with inverter/digital panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete. |
| 203 | Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 4.1TR (1218 cfm) to 5.0TR (1624 cfm)of suitable cfm having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordlessremote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation. |
| 204 | Supplying and erecting circular flexible/rigid PVC pipe duct of size 40mm dia, 4mm thickness with required couplers, reducers, T-joints, Y-joints elbows and necessary supports etc. with sealing with provided control/air flow regulating valves/dampers, filters at position complete. |
| 205 | Supplying and erecting circular flexible/rigid PVC pipe duct of size 50mm dia, 4mm thickness with required couplers, reducers, T-joints, Y-joints elbows and necessary supports etc. with sealing with provided control/air flow regulating valves/dampers, filters at position complete. |
| 206 | Supply, installation, testing and commissioning air curtain of 6feet width having air throw velocity of 21 m/sec, low noise level up to 38 to 46dBA suitable for door height upto 9feet, working on 1 phase, 230V, 50Hz, A.C. supply. |
| 207 | Supplying and installation of high pressure grade required size copper connection Y or T- Joints/refnet complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV/VRF air conditioning system. |
| 208 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 209 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 210 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 211 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 212 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 213 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 214 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 215 | supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, OEM standards of VRV/VRF air conditioning system complete. |
| 216 | Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority |
| 217 | Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG GI sheet of 300 mm width & 100 mm height with required standard accessories. |
| 218 | Supplying, erecting, testing and commissioning of 2 core shielded cable complete. |
| 219 | Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conforM to IS 2878 /15683 coMplete erected with necessary claMp Made froM 50 x 6 MM. M. S. flat with nut & bolts grouted in wall coMplete. |
| 220 | Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 kg capacity with necessary claMp for erection on wall. |
| 221 | Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 MM dia with necessary fittings complete as per specification no. FF-PP |
| 222 | Supplying and erecting G.I. pipe ‘C’ class ERW 150 MM dia with necessary fittings complete as per specification no. FF-PP |
| 223 | Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 1800 to 2280 LPM at 80 to 60 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 30kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP |
| 224 | Supplying, installation, testing and commissioning of jockey fire pump (JP) suitable for water discharge of 180 to 240 LPM at 70 to 50 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per specification no. FF-MFP/JP |
| 225 | Supplying and erecting gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV |
| 226 | Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL |
| 227 | Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FFFFA/NZ |
| 228 | Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC |
| 229 | Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV |
| 230 | Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG |
| 231 | Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS |
| 232 | Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve of size ( 400 x 400 x 400)mm or hose pipe box of size ( 600 x 600 x 200)mm made from min. 1.5 mm thick CRCA sheet with angle iron work of min. of size (25 x 25 x 4) mm having front doors with viewing glass of size (200x150) mm and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5) |
| 233 | Supplying, erecting testing and commissioning optical type smoke detector on suitable back box with necessary connections complete as per specification no. FF-FAS/SD |
| 234 | Supplying, erecting, testing and commissioning manual call point (Pill box) with break glass push button and flip abort switch or agent release switch in metal enclosure complete as per specification no. FF-FAAS/MCP |
| 235 | Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU |
| 236 | Supplying, installing, testing and commissioning of 2 Zones Microprocessor based conventional fire alarm control panel (FACP) with standard accessories , 16x2 Character LCD Display, provision for zone wise contact and beep sound alarm, suitable to operate on 120-220 V AC, 0 - 49 Deg C, 93 ± 2 Percentage RH (non- condensing) at 32 ± 2 Deg C complete as per specification no. FF-FAAS/FACP |
| 237 | Providing/conducting complete fire audit including submission of fire audit report for the whole premises. |
| 238 | Supplying, fixing and commissioning of Spike Light Surface/Wall Mounted Spotlight having IP65 with aluminium body for installation. LED 20W 3000K CCT, 30° beam, Delivered lumens: 1400lm, MacAdam Step 3, glare rating UGR<19, Lifespan: 50,000hrs, Ambient temperature <40° C, L&B Ratio L80B20 with Lumen Maintenance LM80 CRI 90. Standard Warranty 5 Years. |
| 239 | Supplying, fixing and commissioning of Light Up orbit inground luminaire with 5.5W Led 610lm, 3000K, Optics S- Spot 8 Degree Adjustability: FIxed IP68 Dimmable Electronic Power Supply not included. Standard Warranty 5 Years. |
| 240 | Light Up Family Outer Casting made of plastic material for ground, floor, wall and ceiling with closing cap |
| 241 | 12W CC Dali Dimmable Driver |
| 242 | Supplying, fixing and commissioning of Light Up orbit inground luminaire with 2W Led 195lm, 3000K, Optics S- Spot 6 Degree Adjustability: FIxed IP68. Standard Warranty 5 Years. |
| 243 | Light Up Family Outer Casting made of plastic material for ground, floor, wall and ceiling with closing cap |
| 244 | 12W CC Dali Dimmable Driver |
| 245 | Supplying, fixing and commissioning of Linealuce Mini 27R Wall/Ceiling-mounted Wam White-48 Vde-1=1216mm-W warm White-48 Vdc-L-1216mm-Wal Grazing Spot optic 12 2220lmColour: Grey |
| 246 | Pair of adjustable arms- L=41mm for wall or Ceiling installations at all heights - Colour: Steel |
| 247 | Meanwell make 48v 90 watt Dali Dimmable |
| 248 | Supplying, fixing and commissioning of Recessed/ Surface 12W 900lm -3000K CRI 90 Optic: S-Spot 15°, Adjustability: rotation and tilt updown, Size (mm): g51, Driver not included, Colour |
| 249 | 20W CC Dali Dimmable Driver |
| 250 | Supplying, fixing and commissioning of Double Light emission IP65 with RAL finish LED 2.9W , LED lumen 250 lm, 3000K, Standard Warranty 5 Years. |
| 251 | Supply of Keypad with Custom Engraving.; Minimum of Five configurable buttons arranged in one column; engravable and Field- Replaceable Button Caps; Built-in ambient light sensor; One RGB LED backlight per button to illuminate the button engraving; Adjustable brightness and RGB color mixing or pure white across the full range of CCT values; Button feedback and day/night modes; Adjustable blink feedback; 2x IO ports - DC logic or 0-10VDC contact closure or an external input port; Communicate with the Central control system directly with a single communication bus; with all the necessary accessories and faceplate; Install multiple keypads in a single communication bus and controlled by a single control system; IC, FCC Part 15 Class B digital device compliant Keypad and Control System Processor should be from same OEM |
| 252 | Supply of 7 inch widescreen active-matrix Color Display Touch Screen or better; Resolution of 1920x1200 WUXGA display; Brightness 400 nits (cd/m²; Colour depth of 24bit, 16.7M colours; Contrast 1000:1; Viewing angle of ±80° horizontal, ±80° vertical; RAM 2 GB LPDDR3; Capacitive touch screen display;16 GB eMMC Storage for Firmware/Application; 5 or More Virtual buttons in collapsible tool bar; Support H.265, H.264, or MJPEG streaming video decoding and display; RTSP decoding; Supportscheduling applications with Microsoft Exchange Server® and Office 365® software, Google Calendar™ and G Suite™ software; POE+ power sourcing network switch; IoT cloud based remote provisioning, monitoting and managing; Support custom user interface; Built-in speakers; Support MP3 Audio Feedback;USB 2.0 host port to support the room scheduling accessories; Compatible with Ceiling- mounted occupancy sensor for automatically spot ad-hoc room booking; Enterprise-Grade Networking security features - 802.1X authentication, TLS encryption, HTTPS connectivity; Compliance: IC, CE, FCC Part 15 Class B digital device; Touchpanel and Control System Processor should be from the same OEM. |
| 253 | Supply of DIN Rail Mounted DALI Interface; 1 DALI loop.Support minimum of 64 DALI ballasts or 16 groups; Support DT0, DT1, DT2, DT3, DT4, DT5, DT6, DT7 and DT8 Tc DALI Devices; Emergency Override input to bypass the control system; Integrated DALI power supply;3M DIN rail mountable;Communicate with the Central control system via ethernet or 4wire bidirectional communication bus; Powered by PoE or through bus; 3kVAC isolation from Bus (NET) and Ethernet (LAN PoE) ports; MbedTLS encryption; Realtime status of the unit -viewable on the room touchpanel for monitoring and maintaining the system; Install multiple DALI units in a single communication bus and controlled by a single control system; DALI- 2™ Certified; Intertek® Recognized for US & Canada, CE, FCC Class B, IC, WEEE Compliant;The Dimming module and Control System processor should be from thesame OEM. |
| 254 | Supply of DIN Rail High-Voltage Switch with Digital Inputs; 8 channels power switching; 8 voltage-driven isolated digital inputs; 16 Amps Resistive,10 Amps incandescent, 5 Amps fluorescent, 0.5 HP at 120 to 240 Volts AC, 50/60 Hz as maximum load per channel; Total of 80A incandescent; 40A fluorescent at 240VAC per module, 50/60 Hz Support Incandescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, fluorescent, motor load types; Override input; Communicate with the Central control system via 4wire bidirectional communication bus; Realtime status of the unit -viewable on the room touchpanel for monitoring and maintaining the system; Install multiple Relay array units in a single communication bus and controlled by a single control system;UL Listed, CE Compliant The Switching module and Control System processor should be from the same OEM. |
| 255 | Supply of Lighting and AV Control System with control ports; Quad Core processor / multicore CPU / Ultra-Fast processor; real-time, preemptive multi-threaded/multitasking kernel; Transaction-Safe Extended FAT file system; supports up to 10 simultaneously running programs; Control multiple rooms simultaneously; BACnet communication protocol for third-party building management systems (HVAC, security, and other systems) over Ethernet; 2 GB SDRAM and 8 GB flash memory; 8x IR/serial, 1x Bidirectional RS-422/485 port, 2x Bidirectional RS-232, 1x Primary communication port, 8x I/O, 8x low voltage relay; 1x LAN Port for Gigabit Ethernet; Additional 1x Gigabit LAN port for Control subnet supporting DNS server, port forwarding; Isolation mode of control subnet for sensitive applications that require security from the local network; Security protocols - Active Directory® service authentication, 802.1X network access control, TLS, SSH and HTTPS; JITC/FIPS/NIAP certified;TAA compliant / IC3S (Indian Common Criteria Certification) compliant / Common Criteria; Ethernet port with TCP/IP, UDP/IP, DHCP, SSL, SFTP (SSH File Transfer Protocol), IPv4, IPv6 Compliance: UL, CE, FCC, RoHS/WEEE. Control processor & Touch Control interface should be from same OEM, and must not require any internet connectivity for configuration, programming and running.Should be shipped with license to control the room from PC/Laptop using UI.Additional hardware can be used to meet the requirement |
| 256 | Supply of DIN Rail Mountable 4wire network power supply module, 60watts power output; 6x power outlet port; Support 100 to 270 Volt 50/60 Hz; 6DIN module; BIS Compliant; The Power Supply module and Control System processor should be from the same OEM. |
| 257 | Supply of BACnet™ network/IP License for control system; License shall provide native BACnet support directly within the control processor’s operating system; License should support a minimum of 50 BACnet objects per processor, with a scope of expansion.; Should support Read/Write capabilities between the AV control environment and the Building Management System (BMS) over standard Ethernet/IP.; Software should allow direct mapping of control system variables to standard BACnet objects.The Control processor, licenses should be from the same OEM. |
| 258 | Supply of Control Cable, Plenum-Rated (304mtr bundle); Communications backbone for keypads, lighting controllers, shade motors, sensors, and other devices; 1x 18 AWG pair for 24VDC and Ground, and 1x 22 AWG shielded twisted pair for control data; Outer Jacket - Plenum polymer; Data pair - Insulation:Foam FEP, Shield: Aluminum/Polyester; Power Pair - Insulation - plenum polymer; |
| 259 | Supply of 24x1G PoE+ 300W 2x1G and 4xSFP Managed Switch. Switching engineered for 1G AV over IP with rear-facing ports ensuring a clean integration in AV racks. Pre-configured for out of the box functionality |
| 260 | Supply of Custom User Interface dashboard for light control and monitoring;Created using software for comprehensive integration with Control System; Touch screen graphical user interface (GUI) with Smart Objects; integrated, turnkey user interface solutions using HTML5 technology; Should support control and monitoring of lighting for multiple rooms on Touchscreen Panels and Desktop/Laptop application |
| 261 | The scope of work includes the supply, installation, testing, and commissioning of a suitable Distribution Board (DB) box for mounting dimming and switching modules, complete with all necessary accessories such as enclosures, busbars, terminal blocks, MCBs, internal wiring, and supports, as per approved drawings and specifications; the DB box shall be of robust construction, properly ventilated, factory finished, and designed to facilitate easy integration with the Lighting Management System, ensuring safe, reliable, and efficient operation after successful testing and commissioning. |
| 262 | Supply of 12U indoor network rack |
| 263 | Programming of complete system The scope of work includes the complete programming, testing, and commissioning of the Lighting Management System (LMS), covering configuration of lighting zones, dimming levels, sensors, and schedules as per the approved control philosophy, integration with BMS/third-party systems if required, point-to-point and functional testing of all devices, finetuning and calibration, preparation of test reports and as built documentation, and providing necessary training to client/end-user staff to ensure the LMS is fully functional, compliant, and ready for handover. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
