|
| 1 | Jungle clearance |
| 2 | Dag Belling single Kassi stroke minimum 7.5 cm depth |
| 3 | Excavation manually in trenches for pipe lines with straight or open cutting in streets and lanes in builtup area where width of street / Lane from wall to wall is less than 3 meter including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation,watering , including the cost of dewatering of rain water, diversion for traffic, night signals. Providing & fixing caution boards, watching, fencing, etc. and removal of surplus soil from the site upto 15 meter distance complete in all respects. For all classes of soil except rocky. |
| 4 | Excavation by mechanical means (JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation,watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect. (A) Earth work upto 1.5 m. Depth for (i) For all classes of soil except rocky |
| 5 | Excavation by mechanical means (JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation,watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect. (B) Exceeding 1.5 m depth but not exceeding 2.25 m depth. (i) For all classes of soil except rocky |
| 6 | Excavation by mechanical means (JCB or Hydraulic excavator) in trenches for pipe lines with straight or open cutting in streets or open area including trimming and dressing sides levelling of beds of trenches to correct grade, cutting joint holes, refilling consolidation,watering , including the cost of dewatering of rain water, diversion for traffic, night signals. providing & fixing caution boards, crossing over trenches for access to the houses, watching, fencing, etc. and removal of surplus soil out side/inside the town involving lead upto 15 meter complete in all respect. (C) Exceeding 2.25 m depth upto 3.00 m depth. (i) For all classes of soil except rocky. |
| 7 | Providing, laying, fixing, testing and commissioning of 'C' Class heavy duty MS Pipe (600mm) conforming to Indian Standard IS : 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. in ground with anti corrosive treatment with wrapping coating tape (4mm pypkote tape) as per IS : 10221 including cost of primer etc. excluding cost of excavation and refilling complete in all respects. 8 mm thick |
| 8 | Providing, laying, fixing, testing and commissioning of 'C' Class heavy duty MS Pipe (300 mm) conforming to Indian Standard IS : 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. in ground with anti corrosive treatment with wrapping coating tape (4mm pypkote tape) as per IS : 10221 including cost of primer etc. excluding cost of excavation and refilling complete in all respects. |
| 9 | Laying, fixing & jointing of u.P.V.C. Pipes as per ISI-4985 (ISI marked with the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches to correct alignment and gradients, cutting, jointingand testing complete as per specifications. uPVC pipe 2.5 kgf / cm2 of 315 mm. |
| 10 | Providing, Laying, fixing & jointing of ISI Marked HDPE Pipes as per ISI - 4984-1995 casting along the Trenches and laying the same in Trenches to correct alignment and gradients, cutting, jointing and testing complete as per specifications. H.D.P.E Pipe PN 2.5 of 2.5 Kg PE80 630 mm. |
| 11 | Providing, Laying, fixing & jointing of ISI Marked HDPE Pipes as per ISI - 4984-1995 casting along the Trenches and laying the same in Trenches to correct alignment and gradients, cutting, jointing and testing complete as per specifications. H.D.P.E Pipe PN 2.5 of 2.5 Kg PE80 560 mm. |
| 12 | HDPE Reducer PN 4 (4kgfcm2) (630 x 560 mm) |
| 13 | HDPE Reducer PN 4 (4kgfcm2) (630 x 315 mm) |
| 14 | HDPE Reducer PN4 (4kgfcm2) (560 x 315 mm) |
| 15 | HDPE Butt Fusion Bend 90 PN 4 (4kgfcm2) (630 mm) |
| 16 | HDPE Butt Fusion Bend 90 PN 4 (4kgfcm2) (560 mm) |
| 17 | HDPE Butt Fusion Equal Tee PN 4 (4kgfcm2) (630 mm) |
| 18 | HDPE Butt Fusion Equal Tee PN 4 (4kgfcm2) (560 mm) |
| 19 | HDPE LNPE Collar PN 4 (4kgfcm2) with MS Flange 10 mm thickness. 315 mm |
| 20 | Providing and fixing elbow/bends of 90 degree 4 kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge. 315 mm 90° |
| 21 | Providing and fixing elbow/bends of 45 degree 4 kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge. 315 mm 45° |
| 22 | Providing and fixing elbow/bends of 30 degree 4 kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge. 315 mm 30° |
| 23 | Providing and fixing tail end piece 4 kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315 mm |
| 24 | Providing and fixing coupler/socket 4 kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315 mm |
| 25 | Providing and fixing equal tee 4 kg/cm2 pressure as per IS 4985 including testing comissioning and complete in all respect to the specifications of engineer in charge 315 mm |
| 26 | Supply and installation of alfa valve including fittings etc complete in all aspects. 315 mm |
| 27 | Anti theft Mechanism for Alfa valve 315 mm |
| 28 | Providing & fixing double air valve ISI Marked as per IS-14845 including jointing all carriages complete. (e) C.I Double air valve (Size 100mm) |
| 29 | Nuts and Bolts of all sizes and length required |
| 30 | Providing, lowering in trenches to correct gradient and alignment, jointing as per IS code IS 458-2003 into trenches for all depths (pipe for road crossing) Class N.P.2. 400 mm |
| 31 | Providing, lowering in trenches to correct gradient and alignment, jointing as per IS code IS 458-2003 into trenches for all depths (pipe for road crossing) Class N.P.2. 600 mm |
| 32 | Providing, lowering in trenches to correct gradient and alignment, jointing as per IS code IS 458-2003 into trenches for all depths (pipe for road crossing) Class N.P.2. 700 mm |
| 33 | Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation |
| 34 | Cement Concrete 1:4:8 with stone ballast 20 mm gauge mixing by mechanical means using concrete volume type mixture |
| 35 | Cement concrete 1:3:6 With stone ballast or shingle mixing by mechanical means using concrete mixer volumetric type |
| 36 | Cement concrete 1:2:4 With stone ballast or shingle mixing by mechanical means using concrete mixer volumetric type |
| 37 | First class burnt brick work laid in cement sand mortar 1:4 in foundation and plinth |
| 38 | First class burnt brick work laid in cement sand mortar 1:4 in first storey upto 4 metres above plinth level. |
| 39 | 12.5 mm thick Cement Plaster 1:3 |
| 40 | 12.5 mm thick Cement Plaster 1:4 |
| 41 | Reinforced cement concrete M-25 mechanically batchmixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth |
| 42 | Reinforced cement concrete M-20 mechanically batchmixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth |
| 43 | Reinforced cement concrete M-30 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure. |
| 44 | Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in superstructure. |
| 45 | Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe500 grade asper IS1786-2008) , for R.C.C works,where not including in the complete rate of RCC including bending and binding placing in position complete. |
| 46 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) |
| 47 | Centering and shuttering for faces of walls, partitions, retaining walls and the like (vertical or battering) including attached pilasters, buttresses etc when curved. |
| 48 | Centring and shuttering for columns (Square or Rectangular) |
| 49 | Centering and shuttering for columns (circular or curved in plain) |
| 50 | Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels. |
| 51 | Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc. |
| 52 | Centring and shuttering for stair cases with sloping with soffits including risers and stringers. |
| 53 | Centring and shuttering for R.C.C. domes |
| 54 | Extra rate for shuttering work done above 4 metres height (where any single storey exceeds 4 metres in height) for every additional height of 1 metres or part thereof. |
| 55 | Upto 5 mtr |
| 56 | Upto 6 mtr |
| 57 | Upto 7 mtr |
| 58 | Upto 8 mtr |
| 59 | Upto 9 mtr |
| 60 | Upto 10 mtr |
| 61 | Upto 11 mtr |
| 62 | Upto 12 mtr |
| 63 | Upto 13 mtr |
| 64 | Upto 14 mtr |
| 65 | Upto 15 mtr |
| 66 | Upto 16 mtr |
| 67 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in charge). A. Class PN-1.6 as per ISI (f) 300 mm i/d Sluice Valves flanged |
| 68 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in charge). B. Class PN-1 as per ISI (f) 500 mm i/d Sluice Valves flanged |
| 69 | Providing & fixing C.I/D.I Flanged end, stem of SS (AIS 1410) and Bronze(gunmetal) working parts Sluice Valves ISI marked 14846-2000, including jointing , testing & cost of Nut ,Bolt & insertion sheet, all carriage complete (with the approval of Engineer in charge). B. Class PN-1 as per ISI (f) 600 mm i/d Sluice Valves flanged |
| 70 | Providing and laying, jointing, fixing, testing ISI Marked G.I. pipe For air vent Pipe (as per IS 1239) B- Class, premium make 100 mm dia including cost of Specials such as tees, bends, sockets elbow etc., cutting, threading and testing in trenches in the ground complete. (100 mm) |
| 71 | Providing MS safety footrest of minimum 6mm thick plastic encapsulated as per IS:10910 on 12mm dia steel bar confirming to IS: 1786 having minimun cross section as 23mm x 25mm and over all minimum length 263 mm and width as 165 mm with minimum 112mm space between protruted legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm |
| 72 | Providing and applying of Swellable type water stop tape etc. |
| 73 | Providing and applying integral crystalline slurry of hydrophilic in natuire for water proofing management etc. (for vertical surface) |
| 74 | Providing and applying integral crystalline slurry of hydrophilic in natuire for water proofing management etc. (for horizontal surface) |
| 75 | Damp proof course 7.5 Cm thick cement concrete 1:2:4 with 2 coats of bitumen 20/30 penetration at 1.65 Kg per sqm laid hot and sanded |
| 76 | Terracing Consisting of Tiles 22.86x11.43x3.83 cm laid over 25 mm mud Plaster7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg/sqm top of R.C.C slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing Complete in all respect |
| 77 | Preparation of plastered surfaces for painting (including sand pepering the surface) using ready mix cement based wall putty by applying two coats to get required finish. |
| 78 | Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface complete in all respect |
| 79 | Distempering with Acrylic washable oil bound distemper (of approved manufacture) two or more coats over one priming coat to give an even shade complete in all respect |
| 80 | Finishing walls with exterior decorative cement based paint such as snowcem ,robbiacem etc. two or more coats to give an even shade complete in all respect |
| 81 | Base course of floor consisting of 100 mm thick cement concrete 1:8:16 and 100mm sand filling using mechanical mixer for mixing of material complete in all respect |
| 82 | Conglomerate floor 40mm thick cement concrete topping 1:2:4 using mechanical mixer for mixing of material complete in all respect |
| 83 | Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in Dark fast Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge |
| 84 | Chowkats of Red meranti Super (18 to 19 kg per cft. Approx.) confirming to ISI specification no 1003 m kiln seasoned of doors and windows including iron hold fasts, corner straps cleats, stops bolts for hold fasts etc, complete fixed in position |
| 85 | Double Rebate (60mm x 150mm) |
| 86 | Single Rebate (60mm x 100mm) |
| 87 | Red meranti Normal Super (18 to 19 kg per cft. Approx.) doors shutter windows shutter including hinges, screw and cords etc. Complete fixed in position |
| 88 | Panelled, glazed or glazed and panelled. (i) 40mm thick (Single Leaf) |
| 89 | Wire Gauge Red meranti wood Super (18 to 19 kg per cft. Approx.) door shutter without springs housed in chowkats. |
| 90 | 35 mm thick |
| 91 | Providing & Fixing glass panes with nails and putty or wooden strip complete in all respect |
| 92 | Glazing area above 0.09 sqm - 5.0mm thick Plate glass (INDIAN) |
| 93 | Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete |
| 94 | I.S.I Designation No. III (size of door 851mm to 1000mm) |
| 95 | Providing and fixing bright finished brass 100 mm mortise latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 96 | Supplying and fixing rolling shutters, of approved make, made of 80mmx1.25mm, M.S. Laths, interlocked together through their entire length and jointed together, at the end, by end locks, mounted on specially designed pipe shaft, with brackets, side guides, 27.5cm long wire spring grade No. 2 and arrangement for inside and outside locking with push and pull operation complete, including top cover 0.80mm thick (payment is to be made for the exact size of opening where rolling shutter is to be fixed) |
| 97 | Providing and fixing G.I. Sheet 0.80mm thick garage doors, with 40mm x 40mm x6mm angle iron frame with diagonal braces, 3.15mm thick gusset plates at the top and 25mm dia meter pulleys and T-iron 50mm x 50mm x 6mm guides at bottom including locking arrangement with handles and pintles, etc. complete in all respect |
| 98 | Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete. |
| 99 | Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc. |
| 100 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 101 | Steel work fixed independently without connecting plates including cutting hoisting and fixing in position |
| 102 | FLATS |
| 103 | Applying priming coat with metal primer on new steel or iron work including preparation of surface. |
| 104 | Providing and fixing in position Chinaware Floor Mounted One Piece EWC type with matching chinaware cistern 10 ltr. Capacity. (without cistern fitting) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge. |
| 105 | Chinaware Floor Mounted One Piece EWC type with matching chinaware cistern 10 ltr. Capacity (without cistern fitting) size 62x37x67 cm with P trap or S trap and seat cover complete in all respect. |
| 106 | Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect. |
| 107 | Providing and fixing vitreous chinaware pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect. |
| 108 | Vitreous chinaware standard white pedestal for wash hand basin |
| 109 | Providing and fixing jet spray with 2'-6\\" long PVC pipe. a) With C.P. Brass nut |
| 110 | Providing and fixing in position vitreous Chinaware white laboratory sinks of approved make (to the approval of Engineerin- charge) consisting of a pair of brackets, C.P. brass waste 40mm complete in all respect. |
| 111 | Size 470mmx370mmx180mm |
| 112 | Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge) complete in all respect. Brass Bib cock/Stop cock 15mm x 400gm |
| 113 | Providing and fixing in position C.P. brass Tumbler Holder of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect |
| 114 | Providing and fixing in position SS Grab Bar Grade 304 of approved make (to the approval of the Engineer-in-charge) fixed in to wall with brass screws complete in all respect. b) 35mm dia 300mm (12”) long |
| 115 | Providing and fixing in position 15mm C.P. Pillar cock foam flow of approved make (to the approval of Engineer-in-charge) |
| 116 | Providing & Fixing in postion stop cock / Angle valve of approved make (to the approval of Engineer-in-charge ) complete in all respect. A) C.P.brass 15mm stop cock Male and female end |
| 117 | Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect |
| 118 | Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge). b) Size 550mmx400mm |
| 119 | Providing & Fixing in position C.P./Aluminium Khunti of approved make (to the approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect. (f) Aluminium khunti with 6 pegs |
| 120 | Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect. |
| 121 | Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-in-charge) with various fixtures complete in all respect. i) C.P. Brass extension piece,25mm long to 50mm long |
| 122 | Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge) complete in all respect. (a) PVC tube connection of size 15 mm x 300 mm with C.P. Brass nut |
| 123 | Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. |
| 124 | Single Socket Type A - 160mm o/d single socket SWR UPVC pipe lines laid complete |
| 125 | Providing & placing in position on terrace (at all floor levels) HDPE water storage tanks of approved make (to the approval of Engineer - in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flo pipes but without fittings and base support for tank. (i) Triple Layer Tanks |
| 126 | Providing and fixing in position G.I. Tank Nipple of approved make (to the approval of Engineer-in-charge) in PVC Water storage tanks complete in all respect. G.I. tank nipple 32mm i/d |
| 127 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes (as per IS:15801-2008) SDR 7.4 U V stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00 m spacing including testing of pipes complete as per direction of Engineer in Charge. |
| 128 | PN - 16 Pipe, 32mm o/d |
| 129 | Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. |
| 130 | For 110mm o/d pipes - Single Tee |
| 131 | For 110mm o/d pipes - P Trap/Floor Trap 110mm x 110mm |
| 132 | Providing and fixing in position SWR UPVC special for soil waste vent or anti syphonage pipes as per as per IS - 14735 including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. |
| 133 | For 160mm o/d pipes - Single Tee |
| 134 | For 160mm o/d pipes - Elbow 90 degree (all side socket) |
| 135 | For 160mm o/d pipes - Vent Cowl |
| 136 | Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with Grating 150mm x 150mm, cover and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm and chamber including cost of all bricks work in cement morter 1:5 cement concrete 1:2:4 in coping around cover and frame etc. as per standard design minimum depth of water should be 150 mm with a minimum seal 50mm. |
| 137 | 150mm internal Diametre S.W.gully trap with H.C.I. grating and cast iron cover weighing approximately 7.26 kg. and frame clear opening 300mm x 300mm and out of side size 330mm x 330mm |
| 138 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes single socketed (working pressure 4 kgf/cm2) conforming to IS : 4985, including fixing with MS clamps. A) U-PVC pipes (working pressure 4 kgf/sqcm) pipe 110 mm dia |
| 139 | Providing and fixing 110 mm dia. U.P.V.C bend for Rain water pipe as per IS:14735 including jointing complete as per specifications and to the entire satisfaction of Engineer- in- charge. A) UPVC 110 mm bend |
| 140 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES : Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½\\" deep for walls and CI 3\\" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- |
| 141 | Wiring fan point (With fan box) |
| 142 | Wiring light point |
| 143 | Wiring 6Amp. wall socket point |
| 144 | Wiring 6Amp. Plug control comprising wall socket point |
| 145 | Wiring 16/20Amp. power plug control point |
| 146 | Wiring light point with double control switches. |
| 147 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES : Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications :- |
| 148 | Heavy Gauge PVC Conduit Pipe 32mm dia. (Flushed) |
| 149 | PVC INSULATED FR COPPER CONDUCTOR CABLES : Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- |
| 150 | Overall size 2.5sq.mm (Un-sheathed) |
| 151 | Supply of Electrical Items |
| 152 | Ceiling Fan 48'' |
| 153 | Heavy duty Exhaust fan 12'' |
| 154 | Tubelight set 36 Watt LED make |
| 155 | LED Light 15 Watt Round/Square |
| 156 | ERECTION OF FANS : |
| 157 | (i) Erection of Ceiling/ Cabin/ Exhaust fan having connection with PVC insulated PVC sheathed two single core copper conductor (FR) cable 0.75 sq.mm complete:- |
| 158 | Erection of Ceiling fan |
| 159 | Erection of Exhaust fan with louver shutter on the wall/ window grill |
| 160 | (ii) Erection of light fixtures on wall/ ceiling having connection with PVC insulatedmPVC sheathed two single core copper conductor (FR) cable 0.75sq.mm complete:- |
| 161 | Erection of 1X20/28/36/40W Box Type (LED/ Fluorescent) light fixture |
| 162 | Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% excavated from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead upto 30 metres |
| 163 | Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position |
| 164 | MS Double Flanged Duck Foot Bends |
| 165 | 600 mm I/D |
| 166 | 300 mm I/D |
| 167 | Double Flanged MS Bell Mouth |
| 168 | 300 mm I/D |
| 169 | Double Flanged MS Puddle Collars |
| 170 | 600 mm I/D |
| 171 | 300 mm I/D |
| 172 | MS Double Flanged Expansion Joints |
| 173 | 600 mm I/D |
| 174 | 300 mm I/D |
| 175 | Providing and fixing of Aluminium Ladder inside Tank |
| 176 | Providing and fixing of CI Man-Hole and frame including locking arrangement etc. |
| 177 | Providing and fixing of Ventilators |
| 178 | Providing and fixing Aviation Obstruction Light complete including wiring etc. |
| 179 | Providing and fixing Aluminium Lightening Conductor complete including wiring, earthing etc. |
| 180 | Supply of MS Clamps Flat 80 mm x 8 mm |
| 181 | Supply & erection of G.I. pipe (A-Class) as per IS:1239 (Part-I) 2004 including sockets, bends, inspection boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications (Galvanized Iron Pipe 25mm dia). |
| 182 | Supplying,fixing and testing at site Automatic electronic type water level indication system with gun metal float sensor and electrical cable suitable for three phase pump submersible / monoblock to be fixed on existing panel for OHSRs complete in all respects. |
| 183 | Providing Stone Pitching at the bed and edge of the Sirhind Canal at Outlet point (60 ft x 30 ft x 15 ft) |
| 184 | Kirloskar Make Pump-Set as per design (435 m3/hour) (2+1(Standby)) |
| 185 | CS CL - 150 GATE/SLUICE VALVE 300 mm (2 for each Pump : 1 @ Suction Side & 1 @ Delivery Side) |
| 186 | CS CL - 150 NRV/CHECK VALVE 300 mm (2 for each Pump: 1 @ Suction Side & 1 @ Delivery Side) |
| 187 | Electromagnetic Flow Meter (Each for 3 pump lines) |
| 188 | Control Panel 50 HP |
| 189 | Three Core Submersible Flat Cable 16 sqmm |
| 190 | PVC copper wire 19/16 ISI marked |
| 191 | Soldier thimble, flexible pipe , copper earth plate, G.I. pipe 1\\" dia, G.I. wire, internal electrification & Double earthing, kitkat, rubber jain etc. (with cost of material & labour) |
| 192 | 3yrs Operation & Maintenance Cost Please Enable Macros to View BoQ information |
