|
| 1 | Surface and heavy duty type Batten Supply of 4 feet, ceiling or wall mounted, SMD LED batten of 20W LED luminaire (i) System efficacy :- Min. 120 lm/W,(ii) operating in ambient temperature :-- 0⁰C to 45⁰C . (iii) Luminaire shall be made up of extruded anodised aluminium housing with polycarbonate high transmissivity diffuser, ensuring uniform illumination glare free lighting, excellent heat dissipation, high durability, scratch resistance and non-rusting features. LEDs used in the product complies with IEC 62471 for Photo-biological safety. With screwless design,. Luminaire shall have FR4 PCB and its LED Driver shall be of Integrated type prewired in product housing, Isolated(iv) IP40 with stainless steel mounting clamps.(v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided.(vi) Burning Hours:- L70 life of 50000 burning hours tested at maximum current.(vii) CCT:- 5700 K(viii) CRI :- minimum 80 with MacAdam CCT binning < 5.(ix) Constant Current with range:- 150-270V AC with internal surge protection of 2.5Kv.(x) Driver of Efficiency > 85%,(xi) Power factor of minimum 0.95(xii) harmonic distortion (THD) less then 10%Manufacturer shall have inhouse lab approved by NABL . LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. |
| 2 | Surface and heavy duty type Supply of 4 feet, ceiling or wall mounted, SMD LED batten of 40W LED luminaire (i) System efficacy :- Min. 125 lm/W,(ii) operating in ambient temperature :-- 0⁰C to 45⁰C . (iii) Luminaire shall be made up of extruded anodised aluminium housing with polycarbonate high transmissivity diffuser, ensuring uniform illumination glare free lighting, excellent heat dissipation, high durability, scratch resistance and non-rusting features. LEDs used in the product complies with IEC 62471 for Photo-biological safety. With screwless design,(iv) IP40 with stainless steel mounting clamps. . Luminaire shall have FR4 PCB and its LED Driver shall be of Integrated type prewired in product housing, Isolated(v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided.(vi) Burning Hours:- L70B50 life of 50000 burning hours tested at maximum current.(vii) CCT:- 5700 K(viii) CRI :- minimum 80 with MacAdam CCT binning < 5.(ix) Constant Current with range:- 150-270V AC with internal surge protection of 2.5Kv.(x) Driver of Efficiency > 85%,(xi) Power factor of minimum 0.95(xii) harmonic distortion (THD) less then 10%Manufacturer shall have inhouse lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. |
| 3 | Recessed Integral, SMD 1x4 LED, IP 20, 40W LED Recess mounted fixture (i) System efficacy :- Min. 130 lm/W,(ii) operating in ambient temperature :-- 0⁰C to 45⁰C . (iii) Luminaire shall have satin finished translucence (HET) diffuser for Uniform illumination and wider light distribution. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED.(iv) IP20 (v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided.(vi) Burning Hours:- L70 life of 100000 Hrs tested at maximum current(Complete LM 80 test report for LED should be submitted for 10000 Hrs of Testing) (vii) CCT:- 5700 K(viii) CRI :- minimum 80 .(ix) Constant Current with range:- input voltage range of 150V to 270V (nominal rated voltage – 240V) with 3 KV internal surge protection(x) Driver of Efficiency > 85%,(xi) Power factor of minimum 0.95(xii) harmonic distortion (THD) less then 10%(xiii) Ripple less then 5%Driver shall be Multistage,Isolated type, constant current topology driver with proper heat sink for heat. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. |
| 4 | Supply & Fixing of Dry Powder Agent (as per IS 4308:2019), ABC type Fire Extinguisher (Stored Recessed Supply of SMD LED, 300 X 300mm IP 20, 24W Recessed downlighter(i) System efficacy :- Min. 100lm/W(ii) operating in ambient temperature :-- 0⁰C to 45⁰C . . (iii) Luminaire shall have aluminium pressure die cast housing in white with HET Diffuser.(iv) IP20 (v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. (vi) Burning Hours:- L70 life of 50000 burning hours tested at maximum current.(vii) CCT:- 5700 K(viii) CRI :- minimum 80.with MacAdam CCT binning < 7.(ix) Constant Current with range:- rated voltage of 240V with 3kV internal surge protection, Power factor of minimum 0.95(x) Driver of Efficiency > 85%,(xi) harmonic distortion (THD) less then 10%, (xii) efficacy of minimum 80%.Driver Manufacturer shall have inhouse lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012 |
| 5 | Bulk head Supply of surface/wall mounted SMD LED bulkhead luminaire of 10W LED fixture (i) System efficacy :- Min. 100lm/W(ii) operating in ambient temperature :-- 0⁰C to 45⁰C . (iii) Luminaire shall be made up of pressure die cast aluminum housing powder coated in dark gray with polycarbonate high transmissivity opal diffuser, ensuring uniform illumination and excellent heat dissipation. LEDs used in the product complies with IEC 62471 for Photo-biological safety. Luminaire is with high quality silicon gasket of IP65 and IK10 protection . EMC/PCT package of wattage of 1-3 W LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. (iv) IP65 and IK08Protection(v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. (vi) Burning Hours:- L70 life of 50000 burning hours tested at maximum current.(vii) CCT:- 5700 K(viii) CRI :- minimum 80 with MacAdam CCT binning < 7 mounted on 1 mm MCPCB with 35 micron cu layer..(ix) Constant Current with range:- Constant Current with range 140-280V AC with internal surge protection of 2.5kV.(x) Power factor of minimum 0.95(xi) harmonic distortion (THD) less then 10%, (xii) Driver of Efficiency > 80%, LED Driver shall be of Integrated type prewired in product housing, Isolated, Constant Current LED Manufacturer shall have inhouse lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. |
| 6 | Tunnel light IP-66 Supply of 20W SMD LED Tunnel Light Luminaire (i) System efficacy :- Min. 100lm/W (ii) operating in ambient temperature :-- 0⁰C to 45⁰C . (iii) Luminaire shall be made up of power coated Extruded Aluminium housing with PC lens & Glass. Luminaire should be made of a single module. All external hardware must be of SS304 grade. LM 80-08 compliant LEDs of EMC/ceramic package of reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided.(iv) IP66 and IK10 protection(vi) Burning Hours:- L70 life of 50000 burning hours tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing)(vii) CCT:- 5700 K(viii) CRI :- minimum 70 with SDCM < 5. LEDs must be driven at max 70% of the rated current. (ix) Constant Current with range:- Constant Current with range 140-285V AC, 4 KV internal surge protection with additional 10KV SPD mounted inside (x) Power factor of minimum 0.95(xi) harmonic distortion (THD) less then 10%, (xii) efficacy of minimum 80%.MCPCB with Aluminium core and copper thickness of 35 micron to be used for LED mounting. LED Driver must have short circuit, open circuit, Auto cut-off protection for low and high input voltage. LED Driver shall be silicone potted, Integrated type, Isolated, Constant Current. Manufacturer shall have inhouse lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. |
| 7 | surface Integral, SMD 1x4 LED, IP 20, 36/40W LED Surface mounted fixture (i) System efficacy :- Min. 130lm/W (ii) operating in ambient temperature :-- 0⁰C to 45⁰C . (iii) Luminaire shall have satin finished translucence (HET) diffuser for Uniform illumination and wider light distribution. (iv) IP20 (v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED(vi) Burning Hours:- L70B50 life of 100000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing),CCT:- 5700 K(vii) CRI:-Minimum 80 with MacAdam CCT binning < 5. LEDs must be driven at max 70% of the rated current. (viii)LED Driver shall be Multistage, Isolated type, APFC, Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 3 KV internal surge protectionfactor of minimum 0.95(ix) Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10%, Ripple<5%(x) Driver of Efficiency > 85%,(xi) efficacy of minimum 80%. Complying to SELV < 60V DC standards. Compliance to Indian Standards of IS10322 Part 5 / Sect 1:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. |
| 8 | Recessed Integral, SMD 2x2 Backlit LED Panel, IP 20, 36W LED recessed mounted fixture (i) System efficacy :- Min. 130lm/W (ii) operating in ambient temperature :-- 0⁰C to 45⁰C . . (iii) Luminaire shall have CRCA housing coated in white (RAL9016) with translucent HET diffuser for uniform illumination and wider light distribution. LEDs used in the product shall comply with IEC 62471. LM 80-08 compliant LEDs from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. (iv) IP20 (v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. (vi) Burning Hours:- L70B50 life of 100000 burning hours tested at maximum current(vii) CCT:- 5700 K(viii) CRI :- Min 80 with SDCM < 5. LEDs must be driven at max 70% of the rated current. (ix)Constant Current topology driver with proper heat sink for heat dissipation suitable to operate in input voltage range of 150V to 270V (nominal rated voltage – 240V) with 4KV internal surge protection, Power factor of minimum 0.95(x) harmonic distortion (THD) less then 10%, ripple shall be less than 5%(xi) Driver of Efficiency > 85%,(xii) Efficacy of minimum 80%.Manufacturer shall have in-house lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012 |
| 9 | Flood light Supply of 80W,I- 66 SMD LED Floodlight fixture with (i) System efficacy :- Min. 120 lm/W (ii) operating in ambient temperature Maximum LENS dome top temperature shall be less than 95°C at 45°C ambient temperature. (iii)Luminaire shall be made up of LM6/ADC12 Alloy, non-corrosive, pure polyster power coated die cast Aluminium housing with PC lens. The housing should be completely screwless. Luminaire should have 60° beam angle for uniform light distribution. All external hardware must be of SS304 grade. LM 80-08 compliant LEDs of EMC/ceramic package of wattage of 1W-2W from reputed makes such as Nichia/Cree/ Bridgelux/ Lumiled/ Osram/Seoul should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. (iv) IP66 and IK07 protection. (v) Burning Hours:- L70 life of 50000 Hrs tested at maximum current(Complete LM 80 test report for LED should be submitted for 10000 hrs of testing), CCT:- 5700 K(vi) CRI :- Min 70 with SDCM < 5. LEDs must be driven at max 70% of the rated current. (vii) Constant Current with range:- 5 KV internal surge protection with additional 10KV SPD mounted inside the luminaire and firmly fixed to the housing, Driver must have 440V input voltage protection for 8 hours.(viii) Power factor of minimum 0.95(ix) harmonic distortion (THD) less then 10%, (x) Driver of Efficiency > 85%,(xi) Efficacy of minimum 80%.LED Driver must have short circuit, open circuit, Auto cut-off protection for low and high input voltage. Driver must have 440V input voltage protection for 8 hours. Manufacturer shall have inhouse lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012 |
| 10 | Flood light Supply of 40W,I- 66 SMD LED floodlight luminaire with cradle arrangement having rubber dampener(i) System efficacy :- Min. 115 lm/W (ii) operating in ambient temperature operating in ambient temperature of 0⁰C to 45⁰C (iii) Luminaire shall be made up of Pure Polyester powder coated pressure die cast aluminium body that is corrosion resistant. Specially designed aluminum heat sink of pure polyster powder coating to prevent heat build up in light and driver compartments, reducing hot spots and enabling good air circulations. Luminaire shall be designed with non-yellowing polycarbonate fresnel lens that ensures uniform, volumetric & glare free illumination. It should be equipped with high purity integrated IP66 lens with high precision light output. EMC/ceramic package of wattage of 1-5W LEDs used in the product shall comply with IEC 62471 for Photo-biological safety. Luminaire shall be with IP66 and IK08 protection. (iv) IP66 and IK07 protection. (v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED (vi) Burning Hours:- L70 life of 50000 Hrs tested at maximum current(vii) CCT:- 5700 K (viii) CRI :- Min 70 with MacAdam CCT binning <5 mounted on 1.6mm MCPCB with 35 micron cu layer. LED driver made up of die cast aluminium housing shall be silicone potted, Integrated type, Isolated, Constant Current with range 150-300V AC and driver accessories be pre-wired in driver compartment and isolated from optical compartment. . LEDs must be driven at max 70% of the rated current. (ix) Constant Current with range:- 4 KV internal surge protection with Auto Cutoff protection(x) Power factor of minimum 0.95 (xi) harmonic distortion (THD) less then 10%, (xii) Driver of Efficiency > 85% (xiii) Efficacy of minimum 80%.Manufacturer shall have inhouse lab approved by NABL. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Sect 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec13) : 2012; IS 16108 : 2012. |
| 11 | Post top Providing Minimum lumen output 4500 lm Post top Luminarie(i) System efficacy :- Min. 100 lm/W (ii) operating in ambient temperature operating in ambient temperature of 0⁰C to 45⁰C (iii) Luminarie made of single piece construction powder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser and Aluminium anodised with sand blast reflector. (iv) IP65 and IK07 protection. (v) LED:- LM 80-08 compliant LEDs from reputed makes such as Nichia / Cree / Bridgelux / Lumileds should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall use SMD type LED(vi) Burning Hours:- L70 life of 50000 Hrs tested at maximum current(vii) CCT:- 4000 K(viii) CRI :- Min 70 with SDCM < 5. LEDs must be driven at max 70% of the rated current. (ix) Constant Current with range:- 4KV Surge Protection.(x) Power factor of minimum 0.95 (xi) harmonic distortion (THD) less then 10%, (xii) Driver of Efficiency > 85%, (xiii) Efficacy of minimum 80%. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect. OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. |
| 12 | Minimum lumen output 4500 lm Post top Luminarie |
| 13 | Installation, Testing and commissioning of Sr. No. 1 to 11 including tools and machinery as required on site at the time of ITC Works P&F of M.S. J-hook of standard design made out of 16 mm dia. M.S. round bar and fixed with cement concrete mortar with required support as required. Please Enable Macros to View BoQ information |
