|
| 1 | CIVIL & SANITARY WORKEarth work in excavation in foundation trenches in hard soil (vide classification of soil item - A+B) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I. |
| 2 | Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume) |
| 3 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume) |
| 4 | Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I. |
| 5 | Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I. |
| 6 | Providiag designation 75B brick work in Cement Mortar (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l. |
| 7 | Providiag 125mm thick reinforced designation 75A brick work in Cement Mortar (1:4) in super structure with approved quality of clean coarse sand of F.M. 2 including providing 10mm thick mortar joint, cost of screening materials, raking out joints to 15mm depth, curing taxes and royalty all complete job as per building specificition and direction of E/l. |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) |
| 10 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 11 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)In Column |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns etc. for mass concrete. |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and platform. |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 16 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges. |
| 18 | Providing TMT steel reinforcement as per approved design and drawing excluding carriage of M.S bar to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.8mm dia bar |
| 19 | Providing TMT steel reinforcement as per approved design and drawing excluding carriage of M.S bar to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.10mm dia bar |
| 20 | Providing TMT steel reinforcement as per approved design and drawing excluding carriage of M.S bar to work site, cutting, bending end binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per building specification and direction of E/I.12mm dia & above bar |
| 21 | Supplying, and fixing fan hook of 16mm dia M.S. bar 1 meter long bent to required size and shape , placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where materials is not supplied by the deptt.) |
| 22 | Supplying, fitting and fixing 20 gauge G.C.I. sheet gate fitted on. M.S. angle frame of size 60 x 60 x 6mm including cost of fabrication providing necessary locking arrangement with haskal end dommy duly fixed in P.C.C. (1:2:4) block of required size, applying a priming red lead paint over steel work taxes all complete as per drawing specification and direction of E/I. |
| 23 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x0.90 mm M.S. laths with 1.20 mm thick top cover |
| 24 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Dark shade pigment using ordinary cement |
| 25 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 26 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 27 | Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointing with white cement including rubbing, polishing and cost of curring taxes and royalty all complete as per building specification and direction and E/I. |
| 28 | Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 1.5mm cement punning including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I. |
| 29 | Providing 12 mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 with 1.5 mm cement punning including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direcition of E/l. |
| 30 | Providing 12 mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direcition of E/l. |
| 31 | Providing 6mm cement plaster (1:4) in ceiling with clean coarse sand of F.M 1.5 including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. |
| 32 | Providing 19mm water proof cement plaster (1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other approved water proofing compound including cost of screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. |
| 33 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 34 | Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I. |
| 35 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 36 | Providing two coat of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 37 | Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250 mm apron including cost of EW involved, with 75mm cement concrete (1:4:8) over one brick designation 75A flat soling in proper grade and slope at the base, the drain duly plastered in C.M (1:3) with punning over exposed surface all complete as per specification and direction of E/I. |
| 38 | Supplying, fining and fixing viterous white glazed earthen ware I.W.C of Parry Hindustan or any other I.S.S approved make with 100mm H.C.I \\"p\\" trap 15 liters C.I. or C. pull and let go flushing cistern of names or other I.S.S equivalent make, complete with all fittings. C.I or C.C brackets 32mm alkathene/ P.V.C telescopic flush, pipe about 2M long with one brass coupling and clamps G.I chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I body brass spindle stope cock of weight not less than 50 grins. 15 mm P.V.C connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I.580mm Long with 10 litre low level P.V.C. cistern |
| 39 | Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware Urinal of Parry Hindustan or any other I.S.S approved make with 5 liters capacity C.I. outomatic flushing cistern of Reliance or other I.S.S approved make with all fittings with C.I or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I body brass spindle stop cock of approved quality weight not less than 400 grams, 15 mm P.V.C./Alkethene pipe 450mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with two coats of approved paint over a primer coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/I. |
| 40 | Supplying, fitting and fitting vitreous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed C.I. or M.S. brackets 32m C.I. brass waste, 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350 grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I. |
| 41 | Providing and fixing male ended 15mm dia brass bib cock of approved quality (wt. not less than 350 grams) with extra socket all complete as per specification and direction of E/I. |
| 42 | Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.15mm dia Brass Stop Cock |
| 43 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) 110mm dia Single socketed pipes. |
| 44 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes |
| 45 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work - 32 mm nominal dia Pipes |
| 46 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 47 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 48 | Carriage of materials by diesel truck including loading at source, unloading at work site and stacking properly, labour etc. all complete as per direction of E/I.Cement |
| 49 | Steel |
| 50 | Bricks |
| 51 | Stone Chips |
| 52 | ELECTRICAL WORKWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.Group B |
| 53 | Wiring for sub main wiring with the following size of PVC insulated copper conductor single core cable in surface/recessed PVC conduit etc. as required with taxes all complete as per approved design, drawing and electrical specification and direction of E/I.2 x 1.5 sq.mm + 1 x 1.5 sq.mm earth wire |
| 54 | Wiring for sub main wiring with the following size of PVC insulated copper conductor single core cable in surface/recessed PVC conduit etc. as required with taxes all complete as per approved design, drawing and electrical specification and direction of E/I.2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire |
| 55 | Supplying, fitting and fixing of following size of PVC conduit with accessories in surface etc. as required with taxes all complete as per approved design, drawing and electrical specification and direction of E/I.20mm PVC conduit |
| 56 | Supplying, fitting and fixing of following size of PVC conduit with accessories in surface etc. as required with taxes all complete as per approved design, drawing and electrical specification and direction of E/I.25mm PVC conduit |
| 57 | Supplying, fitting and fixing of following size piano type switch and socket on the existing switch box/cover including taxes all complete as per approved design, drawing and electrical specification and direction of E/I.5/6 amp, one way switch |
| 58 | Supplying, fitting and fixing of following size piano type switch and socket on the existing switch box/cover including taxes all complete as per approved design, drawing and electrical specification and direction of E/I.5/6 amp, 3 pin socket outlet |
| 59 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 60 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). |
| 61 | BORE WELL WITH SOLAR SUBMERSIBLE PUMP SETCost of drilling 115mm/125mm deep bore well in all kinds of soil and rock in rural area for installation of pump set with D.T.H. rig all complete! including supplying all materials, labours, tools, drilling rig, air compressor and equipment as well as fuel, lubricants for making boring and cost of transporting/charges of rig machine & other vehicles up to site of the work as per specification and direction of E/l.(a) Up to 50 mtr Below G.L. |
| 62 | Cost of drilling 115mm/125mm deep bore well in all kinds of soil and rock in rural area for installation of pump set with D.T.H. rig all complete! including supplying all materials, labours, tools, drilling rig, air compressor and equipment as well as fuel, lubricants for making boring and cost of transporting/charges of rig machine & other vehicles up to site of the work as per specification and direction of E/l.(b) Beyond 50 mtr. up to 125 mtr. Below G.L. |
| 63 | Supplying all materials, labours, equipments for lowering 200mm dia M.S. ERS pipes as casing of well thickness 6mm for protecting the sites from falling during the process of drilling ail complete including carriage to work site. |
| 64 | Supplying all tools, equiprnents and labour and doing washing, flushing and developing of drilled tube welt to give clean and clear water all complete as per direction of E/l. |
| 65 | Supplying labour and equipments including 125mm dia M.S. Cap and fitting and fixing over the tube well properly and taking it out as per direction of E/I. |
| 66 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work - 15 mm nominal dia Pipes |
| 67 | Supplying fitting and fixing 3 core 4mm2 flat copper submersible cable FINOLEX/HAVELS make including all taxes,royalty etc all complete job as per direction of E/I. |
| 68 | Providing all installation of Solar Powered Submersible auto run & stop DC Pump Moter (900 WP) of stainless steel suitable for minimum 125 x 115 mm bore well aperation head 60 metre. Discharge rate minimum 2000 LPH eith lowering up to 60 mtrs, 32 mm dai UPVC schedule 80 column pipe & 2.5 sq mm x 3 core flat Submersible cable of IS694 : 1190including mono / poly crystalling PV array tank withstand the wing pressure upto 200 kmph & making suitable arrangement to operate Hand Pump manually in the same bore when there is no solar power including. 05 years warranty against defects in meterial and workmanship with locking arrangement of switch board the system should be eco - friendly. |
| 69 | Providing panel board of 2.00 HP Solar Submersible Pump |
| 70 | Carrying out recuparation Yeild test for ascertaining the discharge of constructed well excavetad profile as directed by the ELC. The test carried out by the drawing down water from the well profile below normal subsuil water level upto full depth rise is recorded the normal water level sub soil water level in the well profile as well as strainer level at pump as per design of W.S. scheme shall be recorded prior to the test including cost of all meterials, over load, labours etc complete as directed. |
| 71 | Goods & Services Tax (G.S.T.) - 18% |
| 72 | Labour Cess - 1% Please Enable Macros to View BoQ information |
