|
| 1 | Schedule 'A' Part-I (B/R itmes)Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) and removing old tar felt/APP, all loose dirt, cement plaster, cleaning the concrete surface including removal & cleaning of vegetation, fungus, moss small trees etc from the roof top with wire brush and washing the roof surface with water to remove all dirt, dust, mud etc complete all as specified and directed. |
| 2 | Material & Labour cutting grooves in brick wall, for inserting App membrane, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 or PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) , ,complete all as specified and directed. |
| 3 | Material & Labour cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) , ,complete all as specified and directed. |
| 4 | Material & Labour PCC (1:2:4) type B0 using 12.50 mm graded stone aggregate as in mass concrete over roof as in padding incl cement slurry @ 3Kg/Per sqm over old RCC surface of roof surface finished even & smooth without using extra cement. ,complete all as specified and as directed. |
| 5 | Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bituminous primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temperature and viscosity 70–160 cps over the primer coat with overlap of 100mm at the side and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture's instructions. The vital physical and chemical parameters of the membrane shell be under :–(i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms(ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d–5147)(iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only , complete, all as specified and as directed.(iv) The work shall be carriout at a height upto 12 metre. |
| 6 | Supply and fixing for cement concrete tiles 30cm x 30cm x 20mm thick, machine pressed, set jointed and laid in neat cement slurry on roofs, laid on and including 15 mm thick in cement mortar and joints and grouted and pointed flush in cement mortar (1:3) mixed with 5% crude oil by weight of cement complete all as specified and directed. |
| 7 | Dismentling of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles ,complete all as specified and directed. |
| 8 | Material & Labour brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 ,complete all as specified and directed. |
| 9 | Material & Labour brick work with sub class -B bricks, in half brick thick walls, built in cement moratr (1:4) straight or curved on plan to any radius ,complete all as specified and directed. |
| 10 | Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc,complete all as specified and as directed. |
| 11 | Rendering 15 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces finished even and smooth without using extra cement ,complete all as specified and directed |
| 12 | Material & Labour rough cast plaster complete as specified in SSR Part–I, clause 14.22 shall consisting of following :– firstly apply under coat in cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied,complete all as specified and as directed. |
| 13 | Material & Labour for rendering 15 mm thick in cement mortar (1:4) up to any height, on any face of brick walls or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 14 | Material & Labour for Rendering 10 mm thick in cement mortar (1:3) up to any height, on any face of ceiling or chajjas or concrete surfaces in patches not exceeding 3 sqm and finished even and smooth without using extra cement , complete all as specified and directed |
| 15 | Preparation of newly plastered or un-plastered surfaces on walls ,chajjas , roof projection , cornices etc. and applying two coats of cement based paint (white or tinted) over a coat of alkali resistant primer, complete all as specified and as directed |
| 16 | Preparation of newly plastered or un-plastered surfaces on walls , cornices etc. and applying two coats of oil bound distemper with painting roller over a coat of 1-2 mm wall putty or two coats to achieve smooth surfaces, , complete all as specified and as directed |
| 17 | Preparation of newly plastered or un-plastered surfaces on ceiling ,chajjas , roof projection ,cornices etc. and applying two coats of white wash , complete all as specified and as directed |
| 18 | Demolition of plain cement concrete (unreinforced) including any type of flooring any descriptionnot not exceeding 15 cm thick, complete all as specified and directed. Note: All Demolished material / debries will be taken by the contractor out side of the cantonment without any extra cost to the Govt.Contractor should quote his rate Keeping this Aspect in mind. |
| 19 | Material & Labour for 25 mm thick Cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in sub base floors, surface finished even and rough to receive floor finishes , complete, all as specified and directed. |
| 20 | Material & Labour Non Skid coloured ceramic tiles joint free premium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 21 | Material & Labour Non Skid coloured ceramic tiles premium/1st quality of same description as of floor tiles in serial item No 20 above but 100mm to 150mm height as in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 complete all as specified and as directed. |
| 22 | Material and labour for 8 to 10mm thick heavy duty (digital) vitrified coloured paver tiles of size 300mm x 300mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) , complete all as specified and as directed Make: Endura of Johnson or Durastone of Somany or equivalent make given in App ‘B’ |
| 23 | All as per above item no 22 but as in skirting over and including 10 mm thick backing coat with cement mortar 1:4 complete all as specified and as directed . |
| 24 | Dismantling floor,hearth or wall tilling including cement mortar bedding (but not backing ),removing serviceable tiles to store and rubbish off premises , ,complete all as specified and directed. |
| 25 | Material & Labour for glazed ceramic coloured tiles 600x300x7 to 8mm thick on vertical surfaces such as dados etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in cement mortar (1 :4) complete all as specified and as directed. |
| 26 | Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings ,complete all as specified and as directed. |
| 27 | Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having zinc coating 150 grams per Sqm (AZ 150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws ,complete all as specified and as directed. |
| 28 | Supply and fixing Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150grams/Sqm (Az-150) as in roof ridge,valley gutter etc fixed with self tapping screws ,complete all as specified and as directed. |
| 29 | Supply and fixing of Structural steel, rolled section as in main and cross beams, hips and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe-410 W (Gde-E-250),complete all as specified and as directed. |
| 30 | Taking down chowkats or frames with shutter area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , ,complete all as specified and directed. |
| 31 | Taking down chowkats or frames with shutter area not exceeding 1.50 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , ,complete all as specified and directed. |
| 32 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast of required dia and length ,complete all as specified and as directed. |
| 33 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid decorative type moulded ( Jointless ) door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with full body threaded star headed counter sunk S.S screws, complete all as per specification & drawing complete all as specified and directed |
| 34 | Supply and fixing of factory made single extruded WPC (Wood PolymerComposite) solid door/ window/ Ceosetory windows & other frames/chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast of required dia and length complete all as specified and directed.NOTE : - (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.(ii) Material manufacture test certificate should be provided before execution of work |
| 35 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid decorative type moulded ( Jointless ) gauzed door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with full body threaded star headed counter sunk S.S screws, complete all as per specification & drawing complete all as specified and directed. Note : Stainless steel wire mesh should be paid under separate item . |
| 36 | Supply and fixing double shutter steel window box type ERW hollow P section comprising of glazed and gauged skeleton shutter fabricated from following sections :–(a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces.(b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leaf of T – section 20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf.(c) Vertical mullion shall be ERW hollow T –section of size 60 x 25 mm made from 1.25 mm thick MS sheet(d) The above steel window shall be deemed to include the following accessories/ fittings :i) Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape– 04 Nos per windowii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf.iii) MS tower bolt stove enamelled 150mm long– 2 Nos per leaf.iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf.(v) Cleat 55 mm long of solid square 15x20x.63mm square – 01 No per leafvi) Pintal hinges 12 x 75 mm – 2 Nos each leafvii) 10mm square Guard bar @ 10 cm c/c welded to frame.(viii) Two coat of Synthetic enamel paint over one coat of red oxide primer.(ix) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in gauzed skelton shutter of window with flat iron 15 x 03 mm with steel screws.(x) 3mm thick sheet glass, ordinary quality and with oil putty in square n. exc 0.5 sqm in each pane fixed in glass shutter of window.(xi) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B–1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.Notes : (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit.(ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessoriries as mentioned above.(iii) The window upto 1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable. The window more than 1.00 metre width shall have two openable leaves on both outer side for gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type. |
| 37 | Resecuring or easing & adjusting shutters of any description exc 1 sq. m and not exc 2 sq. m each, with taking down shutters and refixing of shutter complete all as specified and as directed.. |
| 38 | Material & Labour for running welding in repairs thickness to metal to be welded n exc 6mm complete all as specified and directed. |
| 39 | Preparation of old decorated brick/concrete, plastered / un-plastered surfaces of ceiling by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of white wash on ceiling complete all as specified and directed . |
| 40 | Material and labour complete removal of existing treatment from wall by scrappers or any other means and washing , rubbing down and stopping applying one coats of acrylic distemper on interior surface over and including 1 to 2 mm thick wall care putty white cement based in one or two coats to achieve smooth surfaces, of walls of any description, using painting roller after preparation of brick/concrete, plastered / unplastered surfaces of walls complete all as specified and as directed. |
| 41 | Material and labour preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coats of cement base paint on the wall, pillars, cornices etc complete all as specified and as directed. |
| 42 | Material & Labour for Preparation of old decorated wooden Surfaces one coat of synthetic enamel (ordinary tint) any description, not otherwise, described, over 10cm width or girth complete all as specified and as directed. |
| 43 | Preparing old painted steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 44 | Material & Labour for hacking out old broken glass exc 1.5 sq m (any thickness, size, quality or description) from metal frame including punching or drilling out glazing pins/springs clips and providing and fixing new ones complete all as specified and as directed. |
| 45 | Supply and fixing for sheet glass 3.0mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and as directed. |
| 46 | Supply and fixing as in repair for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staple ,complete all as specified and as directed. |
| 47 | Dismantling wrought iron or mild steel work of any description not otherwise provided for iron door etc,complete all as specified and as directed. |
| 48 | Material and labour for rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe-290-W (Gde E-165) quality 'A' complete all as specified and as directed. |
| 49 | Supply and fixing powder coated aluminium section (minimum thickness of powder coating 50 micron) for doors,windows & partition including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by the Engineer-in-Charge.Note : (a). Glazing shall be measured and paid separately; (b). Weight of aluminium sections shall be as per IS or actual weight which ever less shall be measured. (c). The rates quoted shall be inclusive of neoprene beading, glazing clips, jointing clips, screws, etc as required and the same shall not be measured for arriving the weight; (d). The rates shall be inclusive of locking arrangement including complete packing with silicon gel alround contacting surface of aluminium framework and including matching the existing surface area complete all as specified and directed. |
| 50 | Supply and fixingixing in repair 12 mm thick prelaminated particle board interior grade prelaminated both side with decorative choice laminations and fixed with aluminium frame work or screws to timber frame work complete all as specified and directed |
| 51 | Supply and fixing 5.5mm thick selected quality plain/tinted as approved by GE, glass, in square exc 0.5 Sqm in each pane, fixed with aluminium beading in aluminium door,window&ventilation etc ,complete all as specified and as directed. |
| 52 | Supply and fixing aluminium (Diecast) body hydraulically door closer regulated,designation No.3, universal type,suitable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg ,complete all as specified and as directed. |
| 53 | Supply and fixing Double action floor spring hydraulically regulated made up minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover governing pivot made of brass , other parts made of mild steel heavy duty and fixed ,complete all as specified and as directed. |
| 54 | Supply and fixing GI Metal Suspended ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, and as directed by Engineer-in-charge. GI Metal Ceiling laying perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece. |
| 55 | Supply and fixing 5mm PVC hollow sheet (the thicknees of inner wall 0.7 to 1.00mm) panelling inclusive of solvent cement and fixing at site with U clip or PVC frame as per specifications and drawing complete all as specified including dismantling of existing paneling.,complete all as specified and as directed. |
| 56 | Supply and fixing sinks made of stainless steel with driange board 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 57 | Supply and fixing 32/40mm dia PVC waste pipe of standard length for wash hand basin /Kitchen sink etc as in repair ,complete all as specified and as directed. |
| 58 | Supply and fixing 32mm dia brass chromium plated waste coupling for wash hand basins fixed in repair complete. |
| 59 | Supply and fixing galvanised mild Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. |
| 60 | Supply and fixing brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directe. |
| 61 | Supply and fixing as in repair 15mm bore cast copper alloy chromium plated angular stop valves with capstan head, screwed down, high pressure scrwed both ends for iron pipe or for unions , ,complete all as specified and directed. |
| 62 | Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in horizontal surface of steps, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4 including rounding of front edge/exposed edge complete all as specified and as directed by the Engineer-in-Charge. |
| 63 | Supply and fixing vitreous china white wash hand basin flat back white in colour with pedestal ISI marked of size 550mm x 400mm with 32mm chromium plated waste coupling and PVC waste pipe fixed to walls with CI breckets 2 Nos embedded in CM 1:4 type complete all as specified. |
| 64 | Supply and fixing of 15mm size PVC connection with PTMT nuts of length 600mm complete all as specified and as directed by Engr-in-charge. |
| 65 | Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body, wall flanges and capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed , ,complete all as specified and directed. |
| 66 | Supply and fixing 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor complete all as specified and as directe. |
| 67 | Material and labour for preparation of old decorated brick/concrete, plastered / unplastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of acrylic distemper with painting roller over prepared surfaces of walls pillars, cornices etc. complete all as specified and as directed by the Engineer-in-Charge. |
| 68 | Schedule 'A' Part-II (E/M itmes)Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and as directed. |
| 69 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed. Note :- a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately . |
| 70 | Description all as per serial item No.69 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board, complete all as specified and as directed. |
| 71 | Description all as per serial item No.69 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed. |
| 72 | Material & Labour for concealed point wiring complete with 2.5 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathed cable 1100 volts grade drawn through and including medium grade, ISI marked, PVC conduit,medium grade ISI marked not less than 20 mm dia with accessories fixed concealed/surface type on wall/ roof/ ceiling and including provision of 2.50 sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth conitnuity conductor and connected to common earth dolly with suitable size lugs, including mild steels sunken box or pressed steel terminal box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-1) of 1969 and IS:14772:2000 with earth dolly and coated with two coat of anti corrosive paint over a coat of red oxide primer both internally and externally with and including (provision of new) modular covered plate over sunken box for housing the modular switches, socket outlets., fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for :-Note:-1 Modular metal flush / sunken box, and for modular switch/ socket cover plate & sheet are inclusive in the item rate quoted. |
| 73 | Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts complete all as specified and as directed. |
| 74 | Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed. |
| 75 | Supply and fixing of modular socket outlet 2/3 pin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed. |
| 76 | Supply and fixing of modular socket outlet 3/3 pin combined, (6pin), 6 and 16 Amps, one way, two module, 230 volts complete all as specified and as directed. |
| 77 | Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed. |
| 78 | Supply and fixing electronic Fan regulator modular 100 watt, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed. |
| 79 | Supply and laying sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 80 | Supply and laying sub main wiring with two run of 10 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed .Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 81 | Supply and fixing LED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic driver cool/warm type industrial model complete, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed . Cat part No. LUMILINE+ BS20WLED865SPCSS of make Havells or equivalent in make given in Appx 'B'. |
| 82 | Supply and fixing LED Bldg Security Light Fittings of capacity 35 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed . Cat part No.ENDCITYLIT PLAT + SL35WLED757SASYBOPCWOSPD of make Havells or equivalent in make given in Appx 'B'. |
| 83 | Supply and fixing sheet metal MCB DB SPN 8 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old complete all as specified and as directed by the Engr-in-charge. Cat part No.811826 of make Indo Asian or equivalent make given in Appx 'B'. |
| 84 | Supply and fixing sheet metal MCB DB SPN 12 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old complete all as specified and as directed by the Engr-in-charge. Cat part No.811828 of make Indo Asian or equivalent make given in Appx 'B'. |
| 85 | Supply and fixing MCB SPN, 40 Amps, 240 volt,10 KA , 'B' curve as per site requirement, complete all as specified and as directed . Cat part No 811035 of make Indoasian or equivalent make given in Appx 'B'. |
| 86 | Supply and fixing MCB SP, 5 to 32 Amps, 240 volt,10 KA , 'B' curve as per site requirement, complete all as specified and as directed . Cat part No 811008 to 811015 of make Indoasian or equivalent make given in Appx 'B'. |
| 87 | Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB.20 Amp, 10 KA 'B' curve, complete all as specified and as directed. Cat part No.811955 of make Indo Asian or equivalent in make given in Appx 'B'. |
| 88 | Supply and fixing sheet metal enclosure Vertical triple pole & neutral(VTPN) IP-43 including MCCB 63 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and including lugs/thimbles duly crimped for connection including making smooth the disturbed surface including removing old unserviceable enclosure , complete all as specified and as directed. Cat part No.811888 of make Indo Asian or equivalent in make given in Appx 'B'. |
| 89 | Material and labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test point as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing as in repair complete all as directed by Engineer-in-Charge and earth testing on completion. |
| 90 | Supply and fixing of heavy duty exhaust fan 250mm sweep with corrosion resistant PVC body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, PVC base frame with rubber mountings for silent operation, maximum watt input not more than 25 watt, 1400 RPM, minimum air delivery 210 cum/hr, PVC blades and shutter type louvers self-openable/ close able for protecting the entrance of birds and testing, complete all as specified and as directed by Engineer-in-Charge. Cat part No 70049 of make Bajaj or equivalent make given in Appx 'B'. |
| 91 | Supply and fixing ceiling fan BLDC 1200 mm BEE 5 star rating anti corrosive aluminium body and blades, BIS Certified including all accessories like rubber clamp, down rod complete all as specified and directed by Engr-in-Charge. Model No. HECTOR 500 BLDC of make Orient or equivalent Make given in Appx 'B'. |
| 92 | Note:- Amount of credit of Rs. 91,541.00 for retrieved materials is mentioned in Schedule of Credit Page No. 123 of tender doCubic metre ents in pdf form which will be deducted offline while acceptance of tender. Please Enable Macros to View BoQ information |
