|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) with and including removing rubbish material from building and thrown in low lying empty area complete all as specified and as directed by Engineer-in-charge. |
| 2 | Demolition cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness below or above ground level with and including removing rubbish material from building and thrown in low lying empty area complete all as specified and as directed by Engineer-in-charge. |
| 3 | Material and Labour 25mm thick Plain Cement concrete 1:2:4 type B-0, using 12.5mm graded Stone aggregate as levelling course complete all as specified and directed by Engr-in-Charge |
| 4 | Material and Labour for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, (shade as approved by Engineer-in-charge ) , area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured/ shade cement to match the colour / shade of tiles , laid over with and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 5 | Material and Labour for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, (shade as approved by Engineer-in-charge ) , area of each tiles not exceeding 0.36 sqm ,in vertical surfaces etc. set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 6 | Material and Labour for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in flooring surfaces set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 10mm thick rendering in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 7 | Material & Labour for Non skid ceramic coloured joint free tiles , thickness 7mm to 8mm thick (square/ rectangular), colour as approved by Engineer-in-charge area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in vertical surfaces etc set and jointed in neat cement slurry @ 3.00Kg per Sqm and pointed in white or coloured cement to match the colour / shade of tiles , laid over with and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 8 | Taking up or down steel tubing 15mm bore and connection complete all as specified and directed by Engineer-in-Charge.Note: if Excavation required , Excavation and earth work shall be measured and paid seperately under appropriate items of schedule 'A' BoQ. |
| 9 | Supply & Fixing 16mm dia 3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings , laid in trenches or fixed to walls and ceilings or laid in floors complete all as specified and directed by Engineer-In-Charge. |
| 10 | Supply & Fixing in replacement Vitreous China bowl urinal flat back, size of 465mm x 355mm x 265 mm white (minimum), with and including providing and fixing plugs,bedding urinal aginst wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe, grating, waste pipe of 32 mm dia low density and union for dishcarge pipe all complete and directed by Engr in Charge. |
| 11 | Supply and fixing in replacement 15mm bore Stop valve cast copper alloy, chromium plated (ISI marked) with crutch or butterfly handle, screwed down, screwed both end for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge. |
| 12 | Supply and fixing in replacement 20mm bore bib tap cast copper alloy, chromium plated, fancy type (ISI marked) with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as specified & directed by Engineer-in-charge. |
| 13 | Supply & Fixing in replacement 20mm dia Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm- 125gms) complete all as specified and directed by Engineer-In-Charge. |
| 14 | Supply & Fixing in replacement waste pipes 32 mm dia of pressure rating 6kg/sq,cm with all fitting and fixtures all complete as specified and directed by Engineer-In-Charge. |
| 15 | Supply & Fixing in replacement vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified complete all as specified and directed by Engineer-in-charge. |
| 16 | Dismantling of plain or corrugated steel sheeting any gauge, thickness including roof covering etc complete all as specified and directed by Engineer-in-Charge. |
| 17 | Material & Labour Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 18 | Material & Labour Pre- painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, Ridge and eaves board, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge. |
| 19 | Supply & Fixing in replacement to 20 mm dia unions brass to connect iron to polyethylene and fixed all complete as specified and directed by Engineer-In-Charge. |
| 20 | Supply & Fixing in replacement to 20 mm dia elbow brass both ends screwed & fixed all complete as specified and directed by Engineer-In-Charge. |
| 21 | Supply and fixing in replacement 600mm x 450mm size bevelled edge mirror selected quality 5mm thick glass mounted on 6mm thick commercial ply and fixed to wooden plugs with chromium plated brass screws and cup washers, including aluminium frame / beading alround made of aluminium channel, complete all as specified and directed by Engineer-in-Charge. |
| 22 | Supply and fixing Health Faucet (ABS Body) mild steel Chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all as specified by Engr-in-charge. |
| 23 | Material & Labour in replacement 4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame complete all as specified & directed by Engineer-in-charge. |
| 24 | Dismantling of timber scantling in framed work under 40 Sqcm, in fillet rails, posts rafters purlin etc complete all as specified and directed. |
| 25 | Material and Labour Clean swan Second class Soft-wood in scantlings in framed work all complete as specified and directed by Engr in charge. |
| 26 | Supply & fixing 2nd class soft wood plain fillets square rectangular or triangular in section wrought fixed with nails not exceeding 3 Sqcm bull ,splayed,chamfered or rounded on one edge or face complete all as specified & directed by Engineer-in-charge. |
| 27 | Supply and Fixing 2nd cl soft wood plain fillets square rectangular or triangular in section wrought fixed with nails exc 3 Sqcm and not exceeding 6 Sqcm bull ,splayed,chamfered or rounded on one edge or face complete all as specified and directed by Engr-in-Charge |
| 28 | Supply & Fixing in replacement 1000 Ltr capacity Rotational Moulded Polyethylene Water Storage tank , cylindrical (vertical top Type) Triple layered white colour with closed , connectiing with and including complete accessories such as nipple, union , elbow , Tees , socket etc. or requiered size , hoisted and fixed in position complete all as specified and as directed by Engineer-in-charge. |
| 29 | Supply & Fixing in replacement 20mm ball brass valves, high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed all complete as specified and directed by Engineer-In-Charge. |
| 30 | Supply & Fixing in replacement 15mm ball brass valves, high pressure, with polythene float and flynut complete screwed for iron pipe or brass ferrule and fixed all complete as specified and directed by Engineer-In-Charge. |
| 31 | Taking down chowkhats or frames with shutters of PVC door , wooden door shutter, (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed by Engineer-in- charge. |
| 32 | Taking down shutters of any description not exceeding 1.00 sqm each but not exc 2 complete all as specified and as directed by Engineer-in- charge. Please Enable Macros to View BoQ information |
| 33 | Taking down shutters of any description not exceeding 1.00 sqm each but not exc 2 complete all as specified and as directed by Engineer-in- charge. Please Enable Macros to View BoQ information |
