|
| 1 | Earth Work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (uptoall width or Sqm on plan), including dressing of sides and ramming of bottoms, upto all lifts including getting out the excavated soil and disposal of surplus excavated soil as directed, up to all leads and lifts. All kind of soil. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level in C.C 1:4:8 (1cement:4 coarse sand:8 graded stone aggregate 40 mm nominal size) i/c carriage of material in all leads and lifts. |
| 3 | Providing and laying Brick bats in C.C 1:8:16 (1cement:8 coarse sand:16 graded stone aggregate 40 mm nominal size) i/c carriage of materials in all leads and lifts. |
| 4 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand ) i/c carriage of material in all leads and lifts. |
| 5 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor all level Cement mortar 1:4 (1 cement :4 coarse sand) inlcuding carriage of material in all leads and lifts. |
| 6 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand) : 4 graded stone aggregate 20 mm nominal size) i/c carriage of material in all leads and lifts. |
| 7 | Centering and shuttering including strutting, propping etc. and removal of formupto all floor level i/c carriage of material in all leads and lifts. |
| 8 | Lintels, beams,plinth beams, girders, bressumers and cantilevers. |
| 9 | Steel reinforcement for R.C.C work including straightening, cutting,bending, placing in position and binding all complete upto plinth/above plinth level. TMT bars of grade Fe-500D or morei/c carriage of materils in all leads and lifts. |
| 10 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, mouldingand polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade i/c carriage of material in all leads and lifts. |
| 11 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc i/c carriage of material in all leads and lifts. complete i/c carriage of material in all leads and lifts. |
| 12 | Providing and fixing 18 mm thick Pre-laminated flat pressed 3 layer(medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) i/c carriage of material in all leads and lifts. |
| 13 | 18 mm thick |
| 14 | 25 mm thick |
| 15 | Providing and fixing stainless steel powder coated handles to required colour and shade with necessary screws, etc. complete including carriage of material in all leads and lifts. 125 mm |
| 16 | 125mm |
| 17 | 100 mm |
| 18 | Providing and fixing stainless steel powder coated tower bolts (barrel type) of required shade and colour with screws, etc. complete including carriage of material in all leads and lifts. 200X10 mm |
| 19 | Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete i/c carriage of material in all leads and lifts. Triple strip vertical type |
| 20 | Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer- in-charge i/c carriage of material in all leads and lifts. |
| 21 | Providing and fixing sliding arrangement in racks/ cupboards/cabinets shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately) i/c carriage of material in all leads and lifts. |
| 22 | Providing wood work in frames of false ceiling, partitionsetc. sawn and fixed in position with necessary stainlesssteel screws etc i/c carriage of material in all leads and lifts. Sal wood |
| 23 | Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete i/c carriage of material in all leads and lifts. 2nd class teak wood 50x50 mm (base and height) |
| 24 | Providing and fixing 6mm thick commercial ply wood ceiling of approved quality with butt jointing and nails (framework and cover fillets to be paid for separately) i/c carriage of material in all leads and lifts. |
| 25 | Providing and fixing 10mm thick Eco -pinewood panelling on ceiling and wall with necessary screws complete in all respects including carriage of material in all leads and lifts. |
| 26 | Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles any size/colour manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles including cutting the tiles wherever required complete in all respects including carriage of material in all leads & lifts. |
| 27 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make in all colours & shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados in a, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete inlcuding cutting the tiles wherever required complete in all respects i/c carriage of material in all leads and lifts. |
| 28 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water thinnable priming coat with cement primer i/c carriage of material in all leads and lifts. |
| 29 | French spirit polishing : Two or more coats on new works including a coat of wood filler i/c carriage of material in all leads and lifts. |
| 30 | Providing and fixing 19 mm thick Commercial Board water proof for wall lining complete with all necessary screws i/c carrige of material in all leads & lifts. |
| 31 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material i/c carriage of material in all leads and lifts. |
| 32 | For thickness of tiles above 25 mm and upto 40 mm |
| 33 | For thickness of tiles 10 mm to 25 mm |
| 34 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid i/c carriage of material in all leads and lifts. |
| 35 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :i/c carriage of material in all leads and lifts. |
| 36 | Single half stall urinal with 5 litre P.V.C. automatic flushing cistern i/c carriage of material in all leads and lifts. |
| 37 | Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern i/c carriage of material in all leads and lifts. |
| 38 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require i/c carriage of material in all leads and lifts. White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 39 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings i/c carriage of material in all leads and lifts. |
| 40 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 610x510 mm bowl depth 200 mm i/c carriage of material in all leads and lifts. |
| 41 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge i/c carriage of material in all leads and lifts. |
| 42 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Flexible pipe i/c carriage of material in all leads & lifts. |
| 43 | 32 mm dia |
| 44 | 40 mm dia |
| 45 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete i/c carriage of material in all leads and lifts. |
| 46 | Providing and fixing 600X120X5mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P brass brackets and guard rail complete fixed with 40 mm long screws, rawl puls etc. complete i/c carriage of material in all leads and lifts. |
| 47 | Providing and fixing C.P. Brass towel ring make as approved by Engineer - in - charge i/c carriage of material in all leads and lifts. |
| 48 | Providing and fixing soil, waste and vent pipes :Sand cast iron S&S pipe as per IS: 1729 i/c carriage of material in all leads and lifts. |
| 49 | 100 mm dia |
| 50 | 75 mm dia |
| 51 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : i/c carrriage of material in all leads and lifts. |
| 52 | 75 mm dia |
| 53 | 100 mm dia |
| 54 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. complete including carriage of material in all leads and lifts. |
| 55 | for 100 mm dia pipe |
| 56 | for 75 mm dia pipe |
| 57 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete i/c carriage of material in all lead and lifts. 75 mm dia Sand cast iron S&S as per IS - 1729 |
| 58 | Providing and fixing plain bend of required degree complete i/c carriage of material in all leads and lifts. Sand cast iron S&S as per IS - 1729 |
| 59 | 100 mm dia |
| 60 | 75 mm dia |
| 61 | Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete i/c carriage of material in all leads and lifts. Sand cast iron S&S as per IS - 1729 |
| 62 | 100x100x100 mm |
| 63 | 75x75x75 mm |
| 64 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. i/c carriage of material in all leads and lifts. 15 mm nominal bore. |
| 65 | Providing and fixing uplasticised PVC connection pipe with brass unions i/c carriage of material in all leads and lifts. 15 mm nominal bore (a) 45 cm length |
| 66 | Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required i/c carriage of material in all leads and lifts. 15 mm nominal bore |
| 67 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms i/c carriage of material in all leads and lifts. 15 mm nominal bore |
| 68 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete i/c carriage of material in all leads and lifts. 15 mm nominal bore |
| 69 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet Sand cast iron S&S as per IS - 3989 i/c carriage of material in all leads and lifts. |
| 70 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms i/c carriage of material in all leads and lifts. |
| 71 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) i/c carriage of material in all leads and lifts. |
| 72 | For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) i/c carriage of material in all leads and lifts. |
| 73 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) i/c carriage of material in all leads and lifts. |
| 74 | Providing and fixing12 mm thick prelaminated particle board pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge i/c carriage of material in all leads and lifts. Pre-laminated particle board with decorative lamination on both sides |
| 75 | Providing and fixing powder coated aluminium handles as per colour and shade approved by the Engineer-in-Charge with necessary screws including carriage of material in all leads & lifts. 125 mm |
| 76 | Providing and fixing powder coated tower bolt (barrel type) as per colour and shade approved by the Engineer-in-Charge with screws etc. complete including carriage of material in all leads & lifts. 200X10 mm |
| 77 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design i/c carriage of material in all leads and lifts. Inside size 90x80 cm and 45 cm deep including SFRC M.H.. cover with frame (Heavy duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 182 kg : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 78 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 100x100 mm size P type i/c carriage of material in all leads and lifts. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 79 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) i/c carriage of material in all leads and lifts. |
| 80 | Providing and fixing 3 mm thick commercial ply wood ceiling of approved quality with butt jointing and nails (frame work and cover fillets to be paid for separately) i/c carriage of material in all leads and lifts. |
| 81 | Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of (i)1st coat of applying cement slurry @or 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm) i/c carriage of material in all leads and lifts. |
| 82 | Providing and fixing powder coated sliding door bolt as per colour and shade approved by the Engineer-in-Charge with bolts and nuts screws etc. complete including carriage of material in all leads & lifts.250X16 mm |
| 83 | Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 Sq.meters and under, including cutting the patch in proper shape,raking out joints and preparing and plaaster the surface of the wall complete, including disposal of rubbish to the dumping ground all complete as per direction of Engineer in charge. With cement mortar 1:4 (1cement:4 coarse sand).i/c carriage of material in all leads and lifts. |
| 84 | Providing and fixing 100 mm dia cromium plated stainless steel grating confirming to BIS specifcation including carriage of material in all leads and lifts. Please Enable Macros to View BoQ information |
