|
| 1 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.MoRTH 15.01; B(I) |
| 2 | Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.MoRTH 12.04, 2100 |
| 3 | Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications.MoRTH 15.04, 1300 |
| 4 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. RCC Grade M30 using batching plant transit mixer & manual placing.MoRTH 15.11, E Case II |
| 5 | Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications. MoRTH 15.13, 1600 |
| 6 | Flexible Apron :Construction of flexible apron comprising of loose stone boulders weighing not less than 40 kg beyond curtain wall.MoRTH 16.11, 2507.2 |
| 7 | Dewatering of ground water below spring level for excavation & foundation concreting and brick work including boring of pipe operational and running charge of Diesel pumps complete.:subsurface dewatering |
| 8 | Same as above Item No. 2 but surface dewatering . |
| 9 | Providing and laying Cement concrete wearing coat M-35 grade including reinforcement complete as per drawing and Technical Specifications.MoRTH 15.18, 2702 |
| 10 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications.MoRTH 15.14, 2706 /2200 |
| 11 | Embankment using Carted Earth:-Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 |
| 12 | GSB Grade 1:- Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per technical specification. Clause 401. |
| 13 | WBM G-2:- Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405) |
| 14 | WBM G-3:- Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405) |
| 15 | Primer Coat :- Providing and applying primer coat with Bitumen emulsion (SS-2) on prepared surface of granular base including cleaning of road surface and spraying primer at rate of 0.70 Kg/Sqm using mechanical means as per Technical Specification Clause 502. |
| 16 | Tack Coat:- Providing and applying tack coat with Bitumen VG-10 using Bitumen distributor at the rate of 0.35 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503. |
| 17 | 20mm thick Open Graded Premixed Carpet:- Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using Bitumen VG-10 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable mixall, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type as per Technical Specification Clause 508) |
| 18 | Seal Coat Type C:- Providing and laying seal coat by mixall with VG-10 grade bitumen sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 510. |
| 19 | Patri:- Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads transporting to site spreading grading to required slope and compacted to meet requirement of table 300.2 with lead upto 1000m as per technical specification clause 303.1(using carted earth) |
| 20 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade . New work (Two or more coats applied @1.43 ltr/10sqm over and including priming coat of exterior primer applied @ 2.20 kg/10sqm) (apex Ultima , Weather coat All quard) asian , berger. |
| 21 | Providing and fixing of Standard Metal Delineator as per IRC 79-2019 consisting of minimum retro reflective unit exposed area of 330 square cm in white color, full cube corner micro prismatic non-metallic retro reflective sheeting on each side conforming with IRC 67 2012 and meeting the coefficient of retro reflection values as per ASTM D 4956 Type XI table specification. The delineator shall be painted with powder coat of minimum 40 microns thickness, on top of which retro reflective sheeting shall be pasted on both sides. The structure shall be manufactured in roll forming process and shall have height not less than 800 mm above the ground, width not less than 100 mm and shall extend not more than 300mm below the ground while being installed. The front and back faces of the delineator should be curved with a radius of not more than 200 mm and with delta angle (or central angle of curve) lying between 20 degree and 30 degree, to increase the visibility of the delineator for vehicles moving in continuous curves. The delineator shall have grooves across the length to make the reflective sheets vandal-proof. ). The retro reflective sheeting shall be tested for 3 year outdoor weathering test in Indian conditions as per IRC 67:2012 & proof of the same in form of government report shall be uploaded which quoting tender. If somehow tender pre qualification condition do not ask for government report then the report shall be submitted to engineer-in-charge before finalization of bill. The delineator is meant for application on gaps in median, traffic islands, dangerous bends, roundabouts, narrow bridges etc. or as desired by site engineer. |
| 22 | providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting vide clause 801.3, friced over aluminium sheeting type-IV 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm x45 cmx60 cm, 60 cm below ground level as per approved drawing.The retro reflective sheeting shall be tested for 3 year outdoor weathering test in Indian conditions as per IRC 67:2012 & proof of the same in form of government report shall be uploaded while quoting tender. xi) 45X90 cm two way Object Hazard Please Enable Macros to View BoQ information |
