|
| 1 | Demolition of brick work built in cement mortar complete all as specified and directed |
| 2 | M & L for brick work with sub-class B brick straight or curved on plan built in cement mortar 1:6 complete all as specified and directed |
| 3 | Taking down cement plaster/Grit plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc removing debris to a distance not exceeding 250 mtr complete all as directed. |
| 4 | M&L rendering 15mm thick in Cement Mortar 1:4 on fair faces of brick or concrete, internal surfaces of walls finished and even & fair without using extra cement complete all as specifed & as directed. |
| 5 | M&L preparation of new plastered wall surfaces and applying two coats of Oil Bound Distemper over and including a coat of alkali resistant primer, over and including 2 mm thick cement based wall care putty complete all as specified and as directed. |
| 6 | M & L for washed stone grit plaster on exterior walls in two layers, under layers 12 mm thick cement plaster 1:4 (1 cement :4 coarse sand) following the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer with 15 mm thick cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand:2 coloured marble stone chipping 10mm nominal size) including using Colour pigment & marble powder as required in ground in panels with groove all around as per approved pattern including scrubbing and washing the top layer with wire brushes and water to expose the stone chippings includind forming groove of uniform size 15mm wide and 15mm deep as per approved pattern complete all as specified and as directed. |
| 7 | Dismantling fencing wiremesh any type from TMT Bar/Fencing post complete all as spd & directed. |
| 8 | Excavation in post hole (similar hole) each N Exc 0.5 Cum getting out, returning filling and ramming earth or brocken rubble mixed with earth around in layer not exc 25 CM watering and removing surplus soil to a distance N Exc 50 M and making good surface complete all as specifide and directed. |
| 9 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-charge. |
| 10 | S&F mild steel joist channel angle for posts and struts in fencing, gate,tank staging and manhole/drain cover including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or Fe 310-0 including demolition of old manhole cover and remove the malba of same outside the MOD land complete all as specified and directed by Engr-in-Charge. |
| 11 | M&L for Plain Cement Concrete Type C2 (1:3:6) (using 40 mm graded stone aggregate) in foundation filling and mass concrete complete all as specified and directed. |
| 12 | Supply only Chain link MS galvanised fencing Weight Not exc 4.00 Kg/Sqm, of any type. |
| 13 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete |
| 14 | M&L for two coats of synthetic enamel paint over a coat of Red oxide primer on new Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 15 | M&L for One coats of synthetic enamel paint on old Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed. |
| 16 | Dismantling of Stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar in floor, aprons etc and including disposal of all debris exc 1.5 KMtr not exc 5 Km. |
| 17 | M&L for 100 mm PCC type D -2 (1:4:8) using 40 mm graded crushed stone aggregate as in Sub base complete all as specified and directed. |
| 18 | M&L for 50 mm PCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate as in levelling course even and rough complete all as specified and directed. |
| 19 | M&L for heavy duty coloured (approved colour) fully vitrified anti-skid paving tiles of size 300 × 300 mm and 11–12 mm thick, suitable for outdoor use, laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry. Joints shall be 3–5 mm wide and pointed in coloured or white cement to match the shade of tiles, including cleaning of surface after laying, complete all as specified and as directed by Engineer-in-Charge. |
| 20 | M&L for heavy duty coloured (approved colour) semi vitrified paving tiles of size 300 x 300 mm x 8 to 10 mm thick, set and jointed in neat cement slurry and pointed in coloured or white cement to match the shade of tiles over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed. |
| 21 | M&L for chequered cement concrete tiles with grey cement & pigments, size 30cmx30cmx 25 mm thick, set, jointed and pointed in neat cement slurry pigmented to match colour/shade of tiles as in floors etc.; laid over & including 20 mm thick screed bed or bedding layer in CM 1:6, etc. complete all as specified and directed by Engr-in-Charge. |
| 22 | M&L for 80 mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 23 | M&L for 60 mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour in any design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 24 | M&L for 20-25 mm thick machine cut kota stone slab flooring jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab laid over 20 mm thick screed bed of CM 1:4 including rubbing and polishing complete all as specified and directed by Engr -in Charge. |
| 25 | M&L for 18-20 mm thick machine cut kota stone slab in riser, steps and skirting jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab laid over 20 mm thick screed bed of CM 1:4 including rubbing and polishing complete all as specified and directed by Engr -in Charge. |
| 26 | M&L 75 mm thick PCC 1:3:6, type C1, using (20mm graded aggregate) as in Plinth protection and finished the surface fair & even without using extra cement, laid in panel , including filling the joints with sand mixed with bitumen in 1:1 ration complete all as specified and directed. |
| 27 | S&Fin repair Kerb stone of 300x300x 100mm thick precasted plain cement concrete type B0 , 1:2:4 , using 12.5mm graded crushed stone aggregate incl earth work for laying kerb stones. |
| 28 | S&F in repair stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement including dismantling of existing MS/SS Grill complete all as specified and as directed. |
| 29 | Providing, fabricating and fixing 24 mm thick WPC (Wood Plastic Composite) decorative jalli, suitable for outdoor application, manufactured through single extrusion process, comprising K-Value 58–60 (Suspension Grade) PVC resin, calcium carbonate and natural fibres (wood powder / rice husk / wheat husk) with non-toxic additives, having minimum density of 650 kg/cum, good screw holding capacity with minimum screw withdrawal strength of 2000 N (face) and 1100 N (edge), minimum compressive strength of 50 N/mm², modulus of elasticity not less than 850 N/mm² and resistance to spread of flame Class ‘A’ category, termite/borer free, water/moisture proof and fire resistant, of approved make manufactured by an ISO 9001:2015 certified company, cut to required size and fixed in position in MS angle frame of size 40x40x5 mm including fabrication of MS frame by cutting, welding, grinding, alignment, levelling and plumbing complete, MS frame treated with one coat of red oxide zinc chromate primer and two coats of approved synthetic enamel paint suitable for exterior exposure, rate inclusive of cost of all materials, labour, tools, plants, scaffolding and sundries, complete in all respects and as directed by Engineer-in-Charge.. (Make - Rajshri or Equivalent ).Note:- The said item shall be fixed over boundary wall/ roof tops and in any other position as required on site. |
| 30 | S & F 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc. incl dismantling of existing sheet, complete all as specified and directed. Please Enable Macros to View BoQ information |
