|
| 1 | ROAD/HARDSTANDINGSurface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as directed and specified. |
| 2 | Removing excavated material to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified & directed. |
| 3 | M&L for laying and compacting 200mm thick (compacted thickness) Granular sub base (GSB) as per Grade-II as specified Table 400-1 of MORTH specifications for Road and Bridge works, 2013 in single layer not exceeding 15cm thick over compacted sub grade with with natural sand, crushed gravel, crushed stone, crushed slag or combination thereof as per grading required. The materials are mechanically mixed,spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100 KN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density. Consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per Table 900-1 of MORTH specifications for Road and Bridge works, 2013 complete all as specified and as directed. |
| 4 | M&L for laying and compacting 150 mm thick (Compacted thickness) of Wet mixed macadam (WMM) grading as per table 400-12 and 400-13 respectively of MoRTH specifications for Road and Bridge works 2013 manufacturated in WMM paint in two layers of 75mm, material comprising of clean, crushed, graded aggregate and granualar material premixed with water to a dense mass, spreading with sensor pavor and rolling with vibratory rollers of capacity 80-100KN static weight and consolidating to required gradient and camber complete all as specified and directed. The finished surface tolerances as per as per table 900-1 of MoRTH specification for road and bridge work all as specified and directed. |
| 5 | M&L for Rolling and consolidation to required gradient and camber of formation surfaces in cutting with power roller of capacity 8 to 12 ton complete all as specified & directed. |
| 6 | M&L for preparing WMM surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified & directed. |
| 7 | M&L for applying evenly a priming/tack coat with bituminous primer using paving bitumen VG-10 at 10 Kg per 10 Sqm complete all as specified & directed. |
| 8 | M&L for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete. all as specified and directed. |
| 9 | M&L repair to potholes any depth, not exc 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutiing around edges to at least 25mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified and directed. |
| 10 | M&L bituminous premix semi-dense asphaltic concrete 40mm consolidated thickness using paving bitumen VG-30 grade with 5.5% binder content by weight of total mix, rolled with 8 to 12 tonne power roller to uniform surface and compacted to required camber and gradient complete all as specified and directed. |
| 11 | M&L for preparation of black bituminous surfaces of road and applying 2.5mm thick thermoplastic road marking paint of specified shade/colour using hot thermoplastic material with semi automatic thermoplastic paint applicator machine filled with profile shoe heater, the material shall be laid uniformly, heated mixer with a starting machanism at a temperature of 160 degree centigrade thickness of paint shall not less than 2mm and not more than 2.5mm, the width of pattern shall be all as directed at site complete all as specified and directed. |
| 12 | S&F Cat's Eye of size 90mm X 110mm x 17mm complete all as specified and directed. |
| 13 | S&F Road safety convex mirror 60cm dia complete all as specified and directed. |
| 14 | S&F ABS speed breaker/Rubber rumbler of size 75H(A) x 500 W(B) x 425 L(C) complete all as specified and directed. |
| 15 | S&F Road safety cones (600mm height) complete all as specified and directed. |
| 16 | S&F Spring Post/Refective Barriers (600mm height) complete all as specified and directed. |
| 17 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortor 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickeness of jonts except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete all as specified and as directed. |
| 18 | M&L for hardcore of broken stone or boulder of gauge not exc 63mm deposited, spread and levelled in layers not exc 15cm thick, watering and ramming to a true surface as in sub base of floor complete all as specified and as directed. |
| 19 | M&L for cement concrete work in pavement/hard standing of flexural strength 40kg/square centimetre in field using 400kg of cement per cubic meter, thickeness of concrete 25cm or less complete all as specified and as directed. |
| 20 | GALVALUME SHEDM&L for PCC 1:4:8 type D-2 (Using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as directed and specified. |
| 21 | M&L for Reinforced cement concrete (design mix) M-25 (20 mm graded aggregates) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.. |
| 22 | M&L for Formwork for flat rough finished finished surfaces of concrete to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams;and similar work; vertical or to batter complete all as specified and directed.. |
| 23 | M&L for Mild steel bars 10mm dia and over (TMT bars Fe-500 grade), cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 24 | S&F Mild Steel framework with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting and to be prepared for hanging or sliding and also fastening and fixing complete conforming to Fe-410W (Gde-E-250) quality-B complete all as specified and directed. |
| 25 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and n exc 10cm, (dia of neck 16 to 20mm) complete all as specified and directed. |
| 26 | S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting etc. n exc 10kg each brackets conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 27 | S&F tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc king rods and staining bolts conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 28 | S & F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1978 grade St- 240 including painted one shop coat of zinc chromate primer paint (including preparation of surfaces) at contractor's workshop before fabrication complete all as specified and directed. |
| 29 | S&F pre- painted galvalume aluminum zinc coating GI Based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 30 | S&F pre- painted galvalume aluminum zinc coating GI Based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 31 | M&L for two coats of synthetic enamel paint over a coat of red oxide zinc chrome of new steel Surfaces of any description, over 10cm in width or girth,not otherwise described complete all as specified and directed. Please Enable Macros to View BoQ information |
