|
| 1 | Demolition of cement Concrete unreinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as directed. |
| 2 | M&L Cement concrete type C-2 (40mm graded stone aggregate) 1:3:6 in foundations, filling and mass concrete complete all as directed by Engr -in- Charge |
| 3 | Dismantling plain or corrugated steel sheeting any gauge, thickness, including nainital or similar pattern roof covering etc ccomplete, all as specified & directed by Engineer-in-charge. |
| 4 | S&F 0.63 mm thick Galvanised, corrugated mild steel shetting with two corrugations side lap, fixed with coach screws, washers, and L - type or J-type or cranked hook bolts/screw in roof sheeting, walls etc. with grade of zinc coating 275 etc complete, all as specified & directed by Engineer-in-charge. |
| 5 | M&L for preparation of new zinc (or galvanised) comoflage pattern surfaces to receive paintng by a coating with moderant solution including washing and cleaning and applying two coat synthetic enamel paint over a coat of zinc crome, red oxide etc complete, all as specified & directed by Engineer-in-charge. |
| 6 | Dismantling wrought iron or mild steel work of any description not otherwise provided for completely all as specified and directed |
| 7 | S&F rolled mild steel section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed |
| 8 | M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete, all as specified & directed by Engineer-in-charge. |
| 9 | M&L for Pre-cast cement concrete block masonry with solid blocks, Type C1 1:3:6 (using 20 mm graded stone aggregate) exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed. |
| 10 | M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, copings, bed plate, plinth courses, roof kerbs or mud stops rounded or chamfered on edges including necessary form work complete all as specified and directed. |
| 11 | Taking down cement plaster on brick wall/concrete surfaces etc including racking out joints hacking for key scrubing down with water etc of any thickness including Dado any description complete, all as specified & directed by Engineer-in-charge. |
| 12 | M&L for 15 mm thick rendering in CM 1:4 on fair face of brick/concrete surface and finished even and smooth without using extra cement incl taking down cement plaster on brick or stone walls etc, raking out joints, hacking for key scrubbing down with water etc all as specified. |
| 13 | M&l for two coats of cement base paint over a coat of alkali resistant primer incl preperation of new surfaces of walls complete, all as specified & directed by Engineer-in-charge. |
| 14 | Dismantling posts or struts (wood, steel or R.C.C.) any section, imbedded in concrete including taking out embedded portion and making good disturbed ground complete, all as specified & directed by Engineer-in-charge. |
| 15 | M&L for RCC type B-1, 1:2:4 using 20 mm graded stone aggregate in precast posts, fencing posts, straining or terminal posts, struts etc for fencing average sectional area exc 100 Sq cm but not exc 250 Sq cm with or without chamfered angles and flat, splayed, rounded or mitred tops and fixed complete all as specified and directed. |
| 16 | M&L Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and as directed. |
| 17 | .-ditto- but 5mm dia and over upto and including 10mm dia as in stirrups spacer and binders complete all as specified and as directed. |
| 18 | S&F Galvanized, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of posts, straining bolts,standard bolt, including securing or tying at crossing with and including provision of galvanized mild steel wire staples or steel pins, etc complete all as specified and directed (Each line of wire to be measured for the purpose of payment). |
| 19 | Supply and fixing in repairs concertina coil 600 mm dia (in stretched position) hot dip galvanized steel wire coated with CLR anti corrosive paint, making diamond shape with the help of dove tail clips (18 SWG) fixed over razor wire with existing angle iron. The concertina coil is to be fixed with razor wire at points wherever coil touches the bottom of razor wire with the help of hog rings (14 SWG) complete all as specified and directed. (Note: razor wire shall be measured and paid separately as S & F in repair). |
| 20 | Dismantling wrought iron or mild steel work of any description, fencing wire mesh, any type not otherwise provided for complete all as specified and directed. |
| 21 | Supply only chain link MS galvanisd fencing, any size or type complete all as specified and directed. |
| 22 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc.including provision of binding wire complete all as specified and directed |
| 23 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 24 | S&F mild steel works as in posts, struts, fire points structure and other section including cutting tops to shape as directed, drilling holes, notching for wire etc and flat iron fillets for work Confirming to Fe-290 (Gde E-165) etc, complete all as specified and as directed. |
| 25 | S&F MS Round bars 10 mm dia and over cut to length bent to shape required and all as specified conforming to gde Fe 410-W (Gde.E-250) quality-A or Fe 290 (Gde-E-165)for securing chain link fencing, Complete all as specified and as directed by Engr-in-Charge. |
| 26 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long and 5 to 10 mm dia of shank complete all as specified and directed. |
| 27 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but n exc 15 cm long and 11 to 15 mm dia of shank complete all as specified and directed. |
| 28 | Demolition of cement concrete of any description and in any position not other wise specifically providede for , Complete all as specified and as directed by Engr-in-Charge. |
| 29 | M&L for plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundations and filling complete all as specified and directed. Please Enable Macros to View BoQ information |
