|
| 1 | Supply of Horizental spindle, horizental split casing Single/Multistage centrifugal pumps of standard make such as KSB/Mather & Platt/Jyoti/Kirloskar conforming to BIS 1520-1980 (latest with upto date amamendments) read with BIS 9137-1978 or latest to handle clear water having turbidity 50 ppm. with impellers, casing ring & shaft sleeves of bronze, shaft of steel with cast iron casing of suitable capacity coupled directly through a flexible coupling on a common base plate to Kirloskar/NGEF/Crompton/Siemen/Jyoti slipo ring/squirrel cage screen protected drip proof induction electric motor suitable for operation on the data given below Motor Make: Kirlosker.125 HP. |
| 2 | Laying ,jointing, with circumferential butt joints by electrical arc welding (Welding thickness shall be equal to pipe wall thickness) and testing of G.I Pipe of Jindal/Surya Roshani /Tata/AST or of approved rate contract of DGS and D / HP Govt make of following diameter confirming to IS:1239:1990 (Part-ii) (latest with up to date amendments having wall thickness as specified below capable of withstanding required test pressure , including manufacturing and fabrication of reducers taper all shorts pieces, bends etc as per site requirement made from parent tubes. The laying of pipe shall also include flanged joints duly welded in three layer (Two inner and one outer) Where ever required as per direction of Engineer in charge (Earth work in trenches and the cost of flanges I/C nut and bolts gasket will be measured and paid for separately) and all operation such as cutting welding and jointing fabrication of bends tees i.e lowering and laying in excavated trench to ensure required level including flushing cleaning and hydraulic testing complete in all respect to the entire satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The welding electrodes shall be as per IS 814 of Advani Overlikon/Over cord s/s make.The damaged portion of the pipe and all specials (if damaged during laying and jointing operation of pipe ) made from the parents tube shall be provided anticorrosive treatment by applying two coats of anticorrosive bituminous paints over a priming coat as per AWWA specification C-203-1978. The rates also includes entire carriage of material ,flushing, Cleaning and Hydraulic testing,DP test of butt welded joints complete in all respect and to the entire satisfaction of Engineer in charge with in all leads and lifts |
| 3 | Providing and installation of submersible pump confirming to ISS9034-1976 along with a directy coupled submersible type squrrile cage electric induction motor suitable for operation on 415-+10% volts 3 phase 50 cycles AC supply water lubericated bearing i/c Supply and fixing of control panel complete with sheet and angle iron fabricvated dully painted and complete with intermal wiring and comprising of air break star delta starter complete with GPSM system to operate through mobiles main switch of suitable amperage T.P. Volt meter an meter phase indicate , Supply and fixing of submersible cable sets 4mmsqmt( 50m length ) Providing and fixing of reputed make of 40mm cast Steel double flanged cast steel reflux valve 1 no of various dia. with req. accessaries in 40 mm dia,rope wire 4mm dia suitable to bear the wight of submersible motor pump set and GI pipe etc including entire carriage of material and supporting clamps submersible set including entire carriage of material upto all leads and lifts. ( Stage 1st 1X 7.5 HP) Static Head = 23M Discharge =5 LPS |
| 4 | Excavation in foundations , trenches etc., in earth work , lift up to 1.50 metres. Stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15 cm. (fifteen centimetres) layers , when required in to plinth and sides of foundations etc., conslolidating each of the disposited layer by ramming and watering and then disposing off all excavated soil as directed with in the load of 20 mtrs. Pick and Jumper work etc. complete as per the direction of the Engineer - in - Charge. |
| 5 | Providing and laying cement concrete 1:4:8 (1cement:4sand:8graded stone agg. 40mm nominal size)and curing complete excluding cost of form work in :- a) Foundation and plinth. |
| 6 | Providing and laying cement concrete 1:11/2 :3 ( 1cement: 1 1/2 sand: 3graded stone aggregate 20 mm nominal size )and curing complete excluding the cost of form work and reinforcement in:- |
| 7 | foundation footing and bases of columns & like mass concrete. |
| 8 | Walls(any thickness but ot less than 0.1 mtr thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level. |
| 9 | Providing & laying CC 1:2:4 1cement:2 sand 4 graded aggregates 20mm nominal size curing complete excluding cost of form work & reinforcement for RCC work in:- with in all leads and lifts as per the directions of the Engineer in charge. |
| 10 | In suspended floor roofs landing shalves & their support balconies,beams, girders bressumers cantilevers upto floor two level |
| 11 | Providing form work with steel plates 3.15mm thick so as to give fair finish I/c centering shuttering propping etc. height of propping below supporting floor to ceiling not exceeding 4mt. Height & removal of same in situ reinforce ment concrete and plain concrete work in :- |
| 12 | Vertical surface such as walls(any thickness) partitions and the like including attached pillasters, butteresses, plinth and string courses and the like. |
| 13 | Flat surfaces such as soffits of suspended floor roofs landing & like floor etc.,upto 200mm thickness. |
| 14 | Edge of slab and break in floor 20 cm wide |
| 15 | Providing mild steel/tor steel reinforcement I/c bending binding and placing in position complete |
| 16 | 20 mm thick cement plasterin two coats , 15 mm and finisinhing coat 5 mm thick on rough side of brics/stone/concrete walls for interior plastering up to floor two level including arrisses, internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth with in all leads and lifts in C.M 1:6 ( 1 cement : 6 sand ) |
| 17 | Providing and laying heavy duty precast cement conrete inter locking precast cement conrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks |
| 18 | Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matters. |
| 19 | Supplying and Fixing woven plains G.I wire fencing of mesh 50mm to 150 mm to any type of standard rails ,strainging bolts etc. including provision of binding wire, staples etc. |
| 20 | Supplying of various materials for pump house.i)Tool Kit with all accessory etc.(ii) Bearing puller, insulation gloves & gress gen iii) Steel / C.I.chairs,Poly table |
| 21 | Steel work welded in built up sections, trusses and framed work including cutting hoisting Fixing in position and applying a priming coat of red lead paint :- |
| 22 | In trusses and trussed purlings in buildings. |
| 23 | White washing with lime on undecorated wall surfaces (two coats) to give an even shade including thoroughly brooming the surface to remove all dirt dust mortor drops and other foreign matter. |
| 24 | Prov. and fixing GMS tubes of following dia in walls, floors , ventilating pipe/ over flow pipe etc. including tube fittings and making the wall, floors etc. good. i.e welding with one feets 25mm flat iran both side of req.pipes. (25mm-80mm) dia. |
| 25 | Providing & fixing cantrolling arrangement with( 25 to 65) mm dia wheel valve i/c all type of tube fitting compelete. |
| 26 | Painting two coats deco paint on RCC Work including cleaning all dirt, dust and other foreign matters other than white paint |
| 27 | Providing, Laying and jointing in trenches,galvanised mild steel tubes (Light grade)confirming to IS-1239 (Part-I) 2004 i/c tube fittings such as Tee, elbow, union & nipple.(earth work in trenches to be measured and paid for separately)i/c all leads and lifts complete. |
| 28 | 15 mm Dia (L) S/S |
| 29 | 20 mm Dia (L) S/S |
| 30 | 25 mm Dia (L) S/S Please Enable Macros to View BoQ information |
