|
| 1 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:All kinds of soil 50 m beyond 1m from cutting edge. |
| 2 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) . |
| 3 | Providing and laying cement concrete 1:5:10 (1 cement: 5coarse sand: 10 graded crushed brick aggregate 40mm nominal sizes) in foundation and plinth including machine mixing, finishing, consolidation, curing and including form work complete. |
| 4 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 5 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Cement mortar 1:6 ( 1 cement : 6 coarse sand) Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level. |
| 6 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class deodar wood 50x12mm . |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for ;(a) Foundations, footings, bases of columns etc. for mass concrete. |
| 8 | (b) Walls (any thickness) including attached pilasters, buttresses, plinth andstring courses etc. |
| 9 | (c) Suspended floors, roofs, landings, balconies and access platforms. |
| 10 | (d) edges under 20 cm wide |
| 11 | 15mm thick cement plaster 1:6 (1 cement, 6 coarse sand) in single coat on rough/fair side of single on half brick walls for interior plastering including arises, internal rounded angles not exceeding 80cm in girth and finished even and smooth (for all floors/heights/levels). |
| 12 | 15 mm thick cement plaster 1:4 (1 cement: 4 coarse sand) in single coat on rough/fair side of single of half brick walls for exterior plastering including arises, internal rounded angles not exceeding 80 cm in girth and finished even and smooth including scaffolding etc. complete ( at all floors/heights/levels. |
| 13 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished but excluding the cost of nosing of steps etc complete. 40mm thick with 20 mm nominal size stone aggregate.without floating coat of neat punny. |
| 14 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc complete. 40mm thick with 20 mm nominal size stone aggregate. |
| 15 | P/F of Ist quality ceramic glazed floor tiles 400 x 400 mm size conforming to IS 13755 SOMANY/NITCO/ KAJARIA/ASIAN of any color as required / approved by the Engineer Incharge laid over 20mm thick bed of cement mortar 1:4 Incl. pointing the joints with white cement & matching pigment complete. Nothing extra shall be paid for wastage. All work upto floor V level |
| 16 | P/F of Ist quality ceramic glazed wall tiles 300x450/300x600 conforming to IS 13753 of minimum thickness 5 mm approved make like SOMANY/NITCO/ASIAN/KAJARIA of any size as approved by the Engineer Incharge laid over 12mm thick bed of Cement mortar 1:3 (1 Cement: 3 Sand) & joining with grey cement slurry @ 3.3 kg/sqm. Incl. joining in while cement mixed with pigment of matching shade complete. Nothing etc. shall be paid for wastage. All work upto floor V level |
| 17 | Laying of available vitrified floor tiles in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08%and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand)including grouting the joints with white cement and matching pigments Size of tile 600x600 mm including skirting etc complete work. |
| 18 | Providing and fixing 16mm thick Udaipur Green (Ist Quality) marble stone flooring over 20mm (average) thick base of cement mortar 1:4 inclluding skirting (1 Cement : 4 coarse sand) laid over and joined with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing complete. All work upto V level. |
| 19 | Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement :4 coarse sand ), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc complete at all levels 16mm thick (Black granite). 9Area of slab over 0.5 Sqm). |
| 20 | Extra for pre finished nosing to treads of steps of marble stone |
| 21 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast /stone aggregate 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete . |
| 22 | Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre,two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications |
| 23 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butthinges bright finished of required size with necessary screws Second class deodar wood 35mm thick |
| 24 | Extra over item no. 23 if frosted glass is used instead of ordinary glass. All work upto floor V level. |
| 25 | Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butthinges bright finished of required size with necessary screws as per direction of Engineer-in-charge Second class deodar wood 35mm thick. |
| 26 | Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete Fixed to openings / wooden frames with rawl plugs screws etc. |
| 27 | Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size withnecessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge Second class deodar wood 35mm thick |
| 28 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to bemeasured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick Second Class teak wood |
| 29 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : i 100 x 10mm |
| 30 | ii 150 x 10mm |
| 31 | iii 200 x 10mm |
| 32 | iv 250 x 10mm |
| 33 | Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 100mm |
| 34 | 150mm |
| 35 | 200mm |
| 36 | P/F mild steel bright finished eye hooks 6” Long of superior quality with screws. |
| 37 | Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete ( Twin rubber stopper ) |
| 38 | Providing and fixing ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm |
| 39 | 300x16mm |
| 40 | Providing and fixing aluminum extruded section body tubular type universal hydraulic door closer,(having brand logo with IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete : |
| 41 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slabwith suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 42 | Structural steel work in built up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete Welded |
| 43 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches duringtransportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 44 | Applying one coat of water thinnable cement primer of approved brandand manufacture on wall surface. |
| 45 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 1 mm thick . |
| 46 | Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) |
| 47 | Applying priming coat With ready mixed pink or grey primer of approved brandand manufacture on wood work (hard and soft wood) |
| 48 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work |
| 49 | Providing and fixing of water proof ply of approved quality (Green/Orchid/Century) including cost of labour, nut bolts for fixing of frames, fevicol, nails etc. filling the surface with chalk putty mixed with surface even and smooth applying priming coat of wood primer and then (two or more coats) with synthetic enamel paint of approved brand and manufacture. Nothing extra shall be paid for any wastage. (For manufacturing Cupboard). All work upto V level. a) 6mm thick |
| 50 | b) 19mm thick |
| 51 | Providing and fixing decorative high pressure laminated sheet of plain/wood grain in gloss/matt/suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S including cost of adhesive of approved quality 1mm thick. |
| 52 | Renewing glass panes, with wooden fillets wherever necessary Float glass panes of thickness 5.0 mm (weight not less than 12.5kg/sqm) |
| 53 | Providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete 150 mm |
| 54 | Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters including fixing with necessary screws etc. complete. Triple strip (Vertical type) |
| 55 | providing and fixing of curtain rods (valet rod) for cupboards, with end brackets,clamps,screws and all fittings complete includung supply and installation of stainless steel rod of 25 mm diameter of approved make and quality as per the direction the engineer incharge etc complete job. |
| 56 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer, |
| 57 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineer-in-Charge. 80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 58 | Providing and fixing Water Closet squatting Pan (Indian Type WC pan) Orissa pattern whit vitreous china WC pan of size 580x440mm with integral type foot rests (Hindware/Parryware/Cera) with 100mm PVC P or S Trap, including cost of Cement concrete 1:2:4 platform, 10 ltr. Low level PVC flushing cistern (Hindware/Parryware/Cera with manually controlled device (Handle Lever) with all fittings, brackets etc. 32mm PVC flush pipe with fittings and complete job including painting of fittings and brackets, cutting and making good the walls and floor whenever necessary |
| 59 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. |
| 60 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer . Jaquar Make COP-167BPM |
| 61 | Providing and fixing 600 x 450 beveled edge mirror of superior glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden clears with C.P. brass screws and washes complete. |
| 62 | Providing and fixing PVC waste pipe for sink or wash basin of approved make. Flexible pipe a) 32 mm dia |
| 63 | b) 40 mm dia |
| 64 | Providing and fixing of C.P brass waste coupling (Jaquar, ALD-709) a) 32 mm dia |
| 65 | b) 40 mm dia |
| 66 | Providing and fixing C.P brass angle valve (Jaquar make- COP-057PM) for wash basin 15mm nominal bore |
| 67 | Providing and fixing C.P brass toilet paper holder with screws etc. |
| 68 | Providing and fixing Towel ring round with Round Flange complete along with necessary items for fitting. Jaquar Make (Code no. CPA-1121RD) |
| 69 | Providing and fixing C.P towel rail 600 mm long complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of Jaquar make (Code No. 1111N) |
| 70 | Providing and fixing C.P Soap Dish holder of standard size of Jaquar (Code No.CPA 1131 N) with steel screws complete. |
| 71 | Providing and fixing C.P Jet with PVC pipe fixed with WC. Jaquar Make |
| 72 | Providing and fixing PTMT Shelf 440mm long, 124mm width and 36mm height of approved quality, colour and make weighting not less than 300 gms (Make Prayag). |
| 73 | Providing and fixing unplasticised PVC connection pipe with brass unions, 45cm length and 15mm nominal bore. |
| 74 | Providing and fixing steel jail (grating) with or without holes for floor traps, 100mm dia and weight not less than 100 gms. |
| 75 | Providing and fixing 15 mm nominal bore of bib cock of approved quality conf to IS: 8931. |
| 76 | Providing and fixing PTMT Ball cock of approved quality, color and make complete with Epoxy coated aluminum rod with L.P/H.P.H.D plastic balls (prayag). 20 /25mm nominal size, 120/152mm long, weighting not less than 198/440gms. |
| 77 | Providing and fixing C.P brass long nose bib cock of Jaquar make (Code No. 107PM) inclusive of C.P cups nipples whenever required. 15mm nominal size |
| 78 | Providing and fixing C.P brass short nose bib cock of Jaquar make (Code No. 037PM) inclusive of C.P cups nipples whenever required. 15mm nominal size |
| 79 | P/F single lever wall mixer of approved make with provision of hand shower , but without hand shower. (Jaquar Code No. 119-PM) 15mm (nominal size). |
| 80 | P/F C.P brass Sink water mixer wall mounted of approved make (Jaquar-Code No. COP-309PM) of 15mm nominal bore |
| 81 | P/F C.P brass concealed stop cock of approved make (Jaquar-Code No. 069KN) of 15 mm nominal bore. |
| 82 | Providing and fixing Salem Stainless Steel A ISI 304 (18/8) Kitchen sink as per I.S 13983 with C.I brackets and stainless steel plug 40mm including painting of fitting and brackets, cutting and making good the walls whenever required. Kitchen sink with drain board 510 x 1040mm bowl depth 200mm. |
| 83 | Providing and fixing C.P shower rose 15mm of Jaquar make complete job wall mounted shower arm code SHA-477 & OHS Code No-1989 |
| 84 | Providing and fixing gun metal non-return valve of approved quality (screwed end) a. 20mm nominal bore i) Horizontal |
| 85 | ii) Vertical |
| 86 | b. 25mm nominal bore iii) Horizontal |
| 87 | iv) Vertical |
| 88 | c. 32mm nominal bore v) Horizontal |
| 89 | vi) Vertical |
| 90 | d. 40mm nominal bore 1) Horizontal |
| 91 | 2) vertical |
| 92 | Providing and fixing brass stopcock of approved quality ISI with lever handle.a) 15mm nominal bore |
| 93 | b) 20mm nominal bore |
| 94 | c) 25mm nominal bore |
| 95 | Providing and fixing brass gate valve of approved quality C.I wheel (screwed end). ISI a) 25mm nominal bore |
| 96 | b) 32mm nominal bore |
| 97 | c) 40mm nominal bore |
| 98 | Making connection of G.I Pipe fittings with PVC Water tank by means of providing tank nipples (brass), washes extra complete for inlet/outlet etc. 20mm to 32mm nominal size |
| 99 | Providing and placing on terrace (at all floors levels) polythene water storage tank ISI: 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and base support for tank [Make Sintex having valid ISI License]. |
| 100 | Making connection with available (at all floors levels) polythene water storage tank at terrace ISI: 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and base support for tank [Make Sintex having valid ISI License]. |
| 101 | Providing laying PVC soil waste and vent pipe (heavy duty) (Make Astral) minimum 4 kg/sqcm pressure including jointing with adhesive. (Fittings for the same shall be paid separately). a) 75 mm dia |
| 102 | b) 100mm dia |
| 103 | c) 150mm dia |
| 104 | Laying available PVC soil waste and vent pipe (heavy duty) (Make Astral) minimum 4 kg/sqcm pressure including jointing with adhesive. (Fittings for the same shall be paid separately). a) 100mm dia |
| 105 | b) 150mm dia |
| 106 | Providing and laying cement concrete 1:5:10 (1 cemnet: 5 coarse sand: 10 grade crushed stone aggregate) 150mm thick all round PVC Pipes including bed concrete as per standard design. a) 100mm dia |
| 107 | b) 150mm dia |
| 108 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth within the campus and lift upto 1.5 m, as directed by Engineer-in-Charge. Hard Rock (Blasting Prohibited) |
| 109 | All kinds of soil |
| 110 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 111 | Providing steel thermo mechanically treated bars conforming to is:45612000 reinforcement for all RCC work including Binding and placing in position complete including cost twisted steel reinforcement and binding with 18-20 gauge, sift drawn concealed steel binding wire complete as per specifications and drawings (upto height of floor V level). |
| 112 | Half Brick Masonry using 2nd class common burnt clay building bricks in cement mortar 1:4 including scaffolding extra and curing complete. |
| 113 | 12 mm cement plaster finished with a floating coat of neat cement 1:4 (1 cement: 4 fine sand). |
| 114 | Providing and laying brick bats of 2nd class common burnt clay bricks in soak pit around the honey comb brick masonry including leveling and compacting extra complete job. |
| 115 | Honey Comb brickwork 10/11.4 cm thick with 2nd class common burnt clay bricks in cement mortar 1:4 (1 cement: 4 coarse sand). |
| 116 | Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1cement :4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size ) including necessary excavation, foundation concrete 1:5:10 (1 cement :5 fine sand : 10 graded stone with common burnt clay (non modular) bricks of class designation 7.5 |
| 117 | Constructing brick masonry manhole cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design inside size 90x80 cm and 60 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 118 | Extra for depth for manhole of Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 119 | Providing MS footrests including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design with 20mm dia steel round bars. |
| 120 | Providing and fixing square mouth S.W. gully trap grade ‘A’ complete with C.I grating brick masonry chamber with water tight C.I cover with frame of 300x300mm size (inside) the weight of cover to be not less 4.50 kg and frame to be not less 2.70 kg as per standard design: 180x150mm size P type with 2nd class common burnt clay bricks. |
| 121 | Providing and fixing S.W intercepting trap in manholes with stiff mixtures of cement mortar 1:1 (1 cement: 1 sand) including testing of joints extra. Complete. a) 100 mm dia |
| 122 | b) 150 mm dia |
| 123 | Cutting holes upto 30x30cm in walls including making good the walls same with bricks (2nd class common burnt clay bricks). |
| 124 | Cutting holes upto 15x15cm in RCC floors and roofs for passing drain pipes extra and repairing the hole after insertion of drain pipe extra with cement concrete 1:2:4 using 20 mm stone aggregate including finishing complete so as to make it leak proof. |
| 125 | P/F G.I pipes complete with G.I fittings and clamps including cutting and making good the walls etc (internal work exposed on walls). a) 15mm dia |
| 126 | b) 20mm dia |
| 127 | c) 25mm dia |
| 128 | d) 32mm dia |
| 129 | e) 40mm dia |
| 130 | Laying available G.I pipes complete with G.I fittings and clamps including cutting and making good the walls extra. (internal work exposed on walls). a) 15mm dia |
| 131 | b) 20mm dia |
| 132 | c) 25mm dia |
| 133 | P/F G.I concealed pipe with fittings and clamps including painting with anticorrosive bitumastic paint, cutting chases and making good the walls. 1) 15 mm dia |
| 134 | 2) 20 mm dia |
| 135 | 3) 25 mm dia |
| 136 | P/F G.I pipes complete with G.I fittings including trenching and refilling extra (external work). a) 15 mm dia |
| 137 | b) 20 mm dia |
| 138 | c) 25 mm dia |
| 139 | d) 32 mm dia |
| 140 | e) 40 mm dia |
| 141 | Laying available G.I pipes complete with G.I fittings including trenching and refilling extra (external work). a) 32 mm dia |
| 142 | b) 40 mm dia |
| 143 | Providing and filling sand of grade V or coarse around G.I pipes in external work a) 15 mm dia |
| 144 | b) 20 mm dia |
| 145 | c) 25 mm dia |
| 146 | d) 32 mm dia |
| 147 | e) 40 mm dia |
| 148 | Providing and fixing G.I Union in G.I Pipe line cutting and threading the pipe and making long screws extra complete (new work). a) 15 mm dia |
| 149 | b) 20 mm dia |
| 150 | c) 25 mm dia |
| 151 | d) 32 mm dia |
| 152 | e) 40 mm dia |
| 153 | Making connection of G.I distribution branch with G.I main of following sizes by providing and fixing tree including cutting and threading the pipes extra complete. a) 15 mm to 20 mm dia |
| 154 | b) 25 mm to 40 mm dia |
| 155 | Providing and fixing PVC fittings with PVC pipes of approved make (ASTRAL) as per specifications. a) PVC, P or S Trap 100 mm dia |
| 156 | b) PVC plain bend i) 75 mm dia |
| 157 | ii) 100 mm dia |
| 158 | iii) 150 mm dia |
| 159 | c) PVC Door Bend i) 75 mm dia |
| 160 | ii) 100 mm dia |
| 161 | d) PVC Floor Trap (self cleaning design) 100 mm inlet and 75 mm outlet |
| 162 | e) Door Tee i) 75 mm dia |
| 163 | ii) 100 mm dia |
| 164 | f) Plain Tee i) 75 mm dia |
| 165 | ii) 100 mm dia |
| 166 | g) PVC Cowl i) 75 mm dia |
| 167 | ii) 100 mm dia |
| 168 | h) PVC Junction 100 x 100 x 75mm |
| 169 | Laying and fixing (available) PVC fittings with PVC pipes of approved make (ASTRAL) as per specifications. a) PVC plain bend 150mm dia |
| 170 | b) PVC Door Bend 100mm dia |
| 171 | P/F Electric Motor Pump in G. Pipeline for lifting of water to tanks of roof level (Make Crompton greaves/servo) 1.0 H.P Capacity |
| 172 | 2.00 H.P Capacity |
| 173 | P/F Maze Hand Shower 95mm Round shape single flow (Face plate stainless steel and ABS body) with rubit cleaning system Jaquar Make (Code HSH-1653 ) |
| 174 | P/F Flexible shower tube 8mm dia and 1.5m long with nuts etc complete job. (Make Jaquar SHA-549D8) |
| 175 | P/F Premium wall bracket stand for hand shower, 35mm dia and 100mm long round shaped etc complete job. (Make Jaquar, Code SHA-555) |
| 176 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stoneaggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc.complete of 50 mm thick with 20mm nominal size stone aggregate. |
| 177 | P/F exposed part of concealed stop cock jaquar make code 083 KPM |
| 178 | Providing and fixing hand Shower (Health Faucet) with 8mm dia 1 meter long flexible tube and wall hook. Jaquar Make (Code No. ALD-573) |
| 179 | P/F white viterous china Pedestal for washbasin completely recessed at the back for the reception of pipes and fittings. (Jaquar Make , CNS-WHT-301) |
| 180 | Providing and fixing of G.I Fittings (G.I specials) 15mm dia G I elbow |
| 181 | 20mm dia G I elbow |
| 182 | 15mm dia G I tee |
| 183 | 20mm dia G I tee |
| 184 | 25mm dia G I tee |
| 185 | 32mm dia G I tee |
| 186 | 15 mm dia G I socket |
| 187 | 20 mm dia G I socket |
| 188 | 25mm dia G I socket |
| 189 | 32 mm dia G I socket |
| 190 | 40mm dia G I socket |
| 191 | G I Nipple 15 mm x 6'' |
| 192 | G I Nipple 15 mm x 4'' |
| 193 | G I Nipple 15 mm x 2'' |
| 194 | G I Nipple 20 mm x 6'' |
| 195 | G I Nipple 20 mm x 4'' |
| 196 | G I Nipple 20mm x 2'' |
| 197 | 20mm to 15mm G I socket (Reducing) |
| 198 | 25mm to any smaller size |
| 199 | 32mm to any smaller size |
| 200 | 40mm to any smaller size Please Enable Macros to View BoQ information |
