|
| 1 | PEDESTAL SCULPTUREEarth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width aswell as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge.All kinds of soil |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 3 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementAll works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 4 | Centering and shuttering including strutting, propping etc. and removalof form for Lintels, beams, plinth beams, girders, bressumers andcantilevers with water proof ply 12 mm thick |
| 5 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 6 | Supplying, fabricating and fixing seated human sculpture of approved design made in metal including CNC cutting, bending, welding, grinding, decorative finishing and protective weather-proof coating. The sculpture shall be 9 ft height including internal structural frame.Fixing over RCC pedestal / plinth with base plate, anchor bolts, dowels and non-shrink grouting, ensuring proper alignment and structural stability including transportation, erection, cleaning and finishing complete as per approved drawings and direction of Engineer-in-Charge.Material: Metal – Weather Proof coating |
| 7 | Providing and fixing machine cut, mirror polished Granite Stone of approved colour and shade, 18 mm thick, for cladding / flooring work over cement mortar bed (1:4) including backing coat, proper alignment, cutting to required size and shape, edge finishing, joint filling with white cement slurry mixed with matching pigment, curing and cleaning complete as per approved design and direction of Engineer-in-Charge. |
| 8 | GAZEBO & FOUNTAINDesign Build and installation of Gazebo of size 40feet breadth x 10 feet height for meditation with proper lighting as instructed by engineer in charge |
| 9 | Supply & Installation of Water fountain in Ancient Design made from Raj nagar White Marble with 04 nos plate stone with electric pump , Water resistent Light , wiring and all necessery water fitting as Directed By Engineer-in-charge |
| 10 | SURFACE ROADEarth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil |
| 11 | Sand fillling under floor including supply of necessary quantity of sand from a distance not exceeding 8 km (5 miles) from the side of work & including watering, dressing etc. rate to include cost of labour and tools & Plants etc required for proper completion of the work . |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 13 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 14 | Supplyig & Laying of Cobble stone 150x150x150 mm including Cement mortar 1:4, 1cement :4 Coarse sand with 20 mm thick base mortar including filling of joints & including all necessary T&P all complete in direction of engineer in charge. |
| 15 | EXTERNAL ELECTRIFICATIONKP-4607 Magudam MidiDimension : 3962mm |
| 16 | KL-4205 Aston Prime,Wattage : 360W LED. |
| 17 | KL-2750 Sudo Mini,Dimension :76 x 87 x 130mm,Wattage : 3W LED. |
| 18 | KL-4269 Nebula-Spike, Dimension :160 x 100 x 494mm, Wattage : 18W LED. |
| 19 | KL-7897 Wall Up Lighter,Wattage : 6W LED. |
| 20 | KL-5558 Sleek Ajna Bollard, Dimension : Ø100 x 900mmWattage : 8W LED. |
| 21 | Wiring point for light with 1.5 sq. mm.FRLSH PVC insulatedmultistrand single core copper conductor cable in pvc conduit with 1.5 sq. mm.FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit partly concealed in the wall and partly laid in slab with ,GP Box,piano type switch and ceiling rose/angle/ batten holder on 3 mm. thick phenolic laminated backelite sheet etc complete in all respect as directed including matching colour wash. |
| 22 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level)including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.63 mm dia (OD-63 mm & ID-51 mmnominal) |
| 23 | Supplying,Installing, Fixing and Testing of Electric Distribution Panels with accessories such as1. Busbar(Busbar 400 Amp made of copper)2. Sheet Metal Work3. Powder Coating4. Internal wiring,5. Labels,6. Earthing7. Nut bolt etc.in the cubical panel board / feeder pillar made of 2.5mm thick CRCA sheet and finished with powder coating including connection testing etc. as required Engineer In charge. |
| 24 | S&F of 6 Amp to 32 Amp. MCB (10 KA)C Curve, CAT A |
| 25 | Supply and Laying of aluminium conductor PVC insulated armourd served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with brunt bricks on sides and on top. on surface the cable run shall be fixed on M.S clamps etc. of suitable size or as directed by the Engineer- incharge complete in all respect. the armouring of the cable shallm be properly connected with the earth conductor by clamps etc.S.I NO. 501(i)25 SQ. MM 3.5 CORE |
| 26 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.uctor2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 27 | Supply & burying of 600 mm. x 600 mm. x 6 mm. G.I. plate vertically for earthing with its top at least 3 meters below ground level complete with 20 mm. diaG.I. pipe & funnel for watering & one earthing lead of one number. 8 to 10 SWG G.I. wire in 15 mm. dia G.I. pipe up to switch board ( from apron to switch board the cost of G.I. pipe & G.I. wire will be extra ) 30 cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal / coke & salt at least 150 mm. thick all-round etc. as per directions of Engineer in-charge complete in all respects as per drawing. |
| 28 | Beautification of Main Gate of FRPmaterial led board and proper design as per engineer incharge |
| 29 | HORTICULTURE Banyan tree |
| 30 | Ashoka Tree |
| 31 | Cycus Palm |
| 32 | Daniella Variegata -herb |
| 33 | Purple Alternanthera- ground cover plant |
| 34 | Yellow Alternanthera |
| 35 | Aspidistra |
| 36 | Spider Plant |
| 37 | Plumera Alba |
| 38 | Crinum Asiaticum |
| 39 | Phyla Nodiflora (ground cover) |
| 40 | Green Grass |
| 41 | Supplying and stacking of good earth at site including royalty but including carriage 1km (earth measusred in stacks will be reduced by 20% for payment). |
| 42 | Supplying and stacking at site dump manure from approved source,including carriage up to 1 km (manure measured in stacks will be reduced by8% for payment) |
| 43 | Mixing earth and manure in specified proportion or as directed. |
| 44 | Rough dressing the trenched ground including breaking the clods. |
| 45 | Fine dressing the ground |
| 46 | Uprooting weeds from the trenched area after 10 to 15 days after flooding with water including disposal of uprooted vegetation. |
| 47 | Providing & laying Selection no. 1 grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same, as per direction of officer in charge |
| 48 | Provision of Submershible Borewell (5 Nos.) (Electricity to operate the Pump will be provided by the Nagar Nigum.) |
| 49 | Installation of water Hydrantswith PVC PipesProviding, laying & jointing in position PVC pipe conforming to IS:4985:2000 and suitable for the respective working pressure with all fittings and accessories e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces etc. jointing as per manufacturers' recommendation, including earth work in excavation and refilling (Earth work includes 450 mm of soil cover the pipe and width of 300 mm) ISI Marked (Supreme / Prince / Kisan make)PVC Pipe 63mm OD-6kg/cm2 |
| 50 | PVC Pipe 40mm OD-6kg/cm2 |
| 51 | Sprinkler & AccessoriesGear Driven Pop up \\"Super Pro\\"Long/short range with 3/4\\" inlet, |
| 52 | Swing Joint 3/4\\" |
| 53 | Service suddle 3/4\\" |
| 54 | Providing & fixing of PVCValve & Valve Box63mm |
| 55 | Valve Box-63mm |
| 56 | Valve Box-40mm |
| 57 | Water Hydant (20mm) |
| 58 | Other requirementsDisc Filter |
| 59 | Pressure Gauge Glycerine Filled, |
| 60 | DRIP LINE AND ACCESSORIESPVC-16mm OD 30cm/40cm spacing Dripper-RainbirdLong/short range with 3/4\\" inlet, |
| 61 | Fitting and AccessoriesElbow, valve16mm, Joinner,endcaps tees etc. |
| 62 | Trenching in ordinary soil up to required depth including removal and stacking of serviceable materials and then disposing of as directed and spreading earth & neatly levelling, breaking clods etc. and making the trenched area with designed mounds, paths and sitting spaces etc. to proper levels by filling with earth or earth mixed with manure and properly watering complete work in required topography as per drawing & specifications. |
| 63 | Supplying and stacking of good earth at site including royalty but including carriage 1km (earth measusred in stacks will be reduced by 20% for payment). |
| 64 | Supplying and stacking at site dump manure from approved source,including carriage up to 1 km (manure measured in stacks will be reduced by8% for payment) |
| 65 | Mixing earth and manure in specified proportion or as directed. |
| 66 | Rough dressing the trenched ground including breaking the clods. |
| 67 | Fine dressing the ground |
| 68 | Spreading of mixed good earth and manure in specified proportions as above and in required thickness. |
| 69 | Uprooting weeds from the trenched area after 10 to 15 days after flooding with water including disposal of uprooted vegetation. |
| 70 | DUSTBINS & BENCHESSupply and fixing of DUSTBIN 70 LIT(APPROX)Height- 4 feetCapacity-50.00 LTR.3 mm FRP Thicknessincluding all complete of work. |
| 71 | Supply and fixing of Victorian BenchFRP & C-Channel |
| 72 | ENTRANCE GATEBeautification of model town park gate with Designer entry as instructed by engineer in charge |
| 73 | Dismantling rcc or rb including stackingand dismantled material incl. etc. all complete. |
| 74 | CAFETERIASupply and Installation of Prefabricated Cafeteria of size 7 feet x 7 feet with proper lighing, ventilation, as directed by engineer incharge |
| 75 | CENTRAL WALL AREAEarth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-incharge. All kinds of soil |
| 76 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 77 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 78 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement:2 coarse sand) to match the existing floor.With Chlorpyriphos/ Linadane E.C. 20% with 1% concentration. |
| 79 | Reinforced cement concrete work in beams, Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 80 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 81 | Brick work in super-structure in 1:6 cement and coarse sand mortar in superstructure for wall thickness 230 cms & below brick work. |
| 82 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
| 83 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 84 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm Please Enable Macros to View BoQ information |
