|
| 1 | SITC of exterior rated Architectural RGBW Linear LED Wall Washer luminaire; suitable for facade lighting with extruded aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness with lens positioned screening to reduce the light spillage and die casted end caps. Total System wattage not exceeding 60W with system lumen output should be > 3600 lm with all LEDs on. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol based control. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PMMA for each LED, offering beam angle of different types such as narrow(10˚), medium(25˚), wide(40˚,60˚) or elliptical(18˚x36˚) as per the site requirement. Fixture should have Height 50mm ± 5% including surface mount base width 50mm ± 5% , length 1000 mm ± 5% with constant locking hinges for simple position control from various angles without special tools. DMX enabler circuit should be inside the Luminaire only. The rated voltage of the Luminaire should be 240Vac, Luminaire shall be offered with integral BIS Approved Potted Driver of IP 66/67 rating made of extruded aluminium to make it more thermal efficient, LED Driver should have Operating input voltage range: 90-305VAC, PF > 0.90. Life time of LED driver should be > 80,000 hours and MTBF of LED driver should be ≥ 2,00,000 hrs, Led driver must have SELV output and Case temperature i.e. Tc ≥90°C. Fixture should be available with 10KV SPD in CM/DM Mode. Fixture's DMX Signal cable should be available with proper loop in loop out features. Fixture shall be suitable to operate at an ambient temperature range of -20°C to 50°C and complete luminaire shall be IP66 and IK07 rated. LED Life time shall be at least L70B50 @ 50,000 burning hours at 50°C. LED should be with ceramic package of make Nichea, Osram, Cree, Lumiled only. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 2 | SITC of 50W Mono LED Flood light, suitable for highlighting architectural features. Luminaire shall be in 3000K CCT with Operating temperature: -10 °C to +50 °C, LED life L70B50: 50000 hours at 50°C. Lumen output should be of >4000 Lumens with Full LED on. CRI >= 80, Housing made of Pure polyester powder coated Aluminum die cast housing in White finish with aesthetically designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant, PMMA Lens, Beam angle of different types such as narrow(10˚), medium(25˚), wide(40˚,60˚) or elliptical(15˚x 30˚) as per the site requirement. Fixture should be Toughened glass cover of 4mm thickness with High Impact Resistance strength of IK07 and IP66. LED should be of Osram/Lumileds/Cree, Built-In Potted IP66/67 electronic LED driver with APFC,lower THD, Open Circuit Protection, Over Voltage Protection, Surge Voltage Protection of 10kV with externally attached SPD. Weight of fixture 3 Kg, Dimension of the fixture should be (312x286x66) mm + 5% for better overall performance & long life. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 3 | SITC of exterior rated Architectural Mono (3000K) Linear LED Wall Washer luminaire; suitable for facade lighting with extruded aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness with lens positioned screening to reduce the light spillage and die casted end caps. Total System wattage not exceeding 40W with system lumen output should be more than >2800 lm with all LEDs on. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PMMA for each LED, offering beam angle of different types such as narrow(10˚), medium(25˚), wide(40˚,60˚) or elliptical(18˚x36˚) as per the site requirement. Fixture should have Height 50mm ± 5% including surface mount base width 50mm ± 5% , length 1000 mm ± 5% with constant locking hinges for simple position control from various angles without special tools. The rated voltage of the Luminaire should be 240Vac, Luminaire shall be offered with integral BIS Approved Potted Driver of IP 66/67 rating made of extruded aluminium to make it more thermal efficient, LED Driver should have Operating input voltage range: 90-305VAC, PF > 0.90. Life time of LED driver should be > 80,000 hours and MTBF of LED driver should be ≥ 2,00,000 hrs, Led driver must have SELV output and Case temperature i.e. Tc ≥90°C. Fixture should be available with 10KV SPD in CM/DM Mode. Fixture's DMX Signal cable should be available with proper loop in loop out features. Fixture shall be suitable to operate at an ambient temperature range of -20°C to 50°C and complete luminaire shall be IP66 and IK07 rated. LED Life time shall be at least L70B50 @ 50,000 burning hours at 50°C. LED should be with ceramic package of make Nichea, Osram, Cree, Lumiled only. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. or equivalent as approved by Eng-in-charge |
| 4 | Supply of exterior rated LED RGBW Flexible LED Strip with 14.4 Watt per meter. LED Strip should have 60Nos LEDs per meter through out the length with the silicon cover with system lumen output should be more than 700 lms /Meter. Standard Length of LED Strip is 5 Mtr and it shall be capable of producing dynamic color changing light for with 16 million colors and should be programmable using 8 bit control DMX512 protocol / Ethernet based control. The Strip should have IP 67 protection with inbuilt IP67 connectors at both ends. DMX enabler circuit should be outside the Luminaire/LED Strip only. LED Strip shall be suitable to operate at an ambient temperature range of -20°C to 50°C. Life time shall be at least L70B50 @ 35000 burning hours at 50°C. LED should of make Nichea, Osram, Cree, Lumiled, Hongya of 5050 SMD package only. The rated voltage of the Luminaire should be 24VDC, Luminaire shall be offered with a BIS Approved Potted Driver of IP 66/67 rating made of extruded aluminium to make it more thermal efficient, Led Driver should have Operating input voltage range: 90-305Vac, PF > 0.95 and must have safety operation range form 90V - 176Vac. Life time of LED driver should be > 80,000 hours and MTBF of LED driver should be ≥ 2,00,000 hrs, Led driver must have SELV output and Case temperature i.e. Tc > 90°C. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (PART 5/SEC 7) and shall be complete with all necessary mounting accessories required for proper working of fixture including driver, decoder, aluminum profile with diffuser cover, weather proof connection cables, water proof connectors etc. as required. Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 5 | Supply, of exterior BIS registered 3000K Flexible LED Strip with 14.4 Watt per meter. LED Strip should have 60Nos LEDs per meter through out the length with the silicon cover with system lumens 1261 lms/meter and System Lumen Efficacy 87lm/w/meter. Standard Length of LED Strip is 5 mtr. The Strip should have IP 67 protection with inbuilt IP67 connectors at both ends. LED Strip shall be suitable to operate at an ambient temperature range of -20°C to 50°C. Life time shall be at least L70B50 @ 35000 burning hours at 50°C. LED should of make Nichea, Osram, Cree, Lumiled, Hongya of 5050 SMD package only. The rated voltage of the Luminaire should be 24VDC, Luminaire shall be offered with a BIS Approved Potted Driver of IP 66/67 rating made of extruded aluminium to make it more thermal efficient, Led Driver should have Operating input voltage range: 90-305Vac, PF > 0.95 and must have safety operation range form 90V - 176Vac. Life time of LED driver should be > 80,000 hours and MTBF of LED driver should be ≥ 2,00,000 hrs, Led driver must have SELV output and Case temperature i.e. Tc > 90°C. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (PART 5/SEC 7) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. or equivalent as approved by Eng-in-charge |
| 6 | Supply of exterior rated Architectural LED Mini 25W sleek flood light with lumens > 2150 lms in 3000K , Power factor > 0.95, CRI > 80 with IP66 and IK07 Gray pure polyester powder coated ,Pressure die-cast aluminium housing for efficient thermal management, sturdiness & excellent corrosion resistance & High quality toughened glass with 4mm thickness in clear finish for uniform light distribution. SS grade metal gland provided for 3 core 1sq mm supply wire. Length 208mm, Width 100 mm and Height 390mm including spike. Life time shall be at least of L70B50@50000 hours and the housing provides IP66 and IK 07 protection for high reliability in outdoor applications with Total System wattage not exceeding 25W. High efficiency long life COB mounted on PDC heat sink with holder and chrome finish reflector. Powered by an Built-In potted, electronic driver (SMPS based constant current supply) with lower THD < 10%, Output Open/ Short circuit protection, Surge voltage protection upto 4kV & other safety test as per IS:15885 Part 2/Sec 13.Lumen efficacy of LED > 140 lm/W. with aluminum heat sink for effective thermal management with Operating temperature: -10°C to +45°C. weighing 1.5 kg apprx. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. or equivalent as approved by Eng-in-charge |
| 7 | Supply of exterior rated Architectural LED Mini 9W sleek flood light with lumens > 620 lms in 3000K , Power factor > 0.95, CRI > 80 with IP66 and IK07 Gray pure polyester powder coated ,Pressure die-cast aluminium housing for efficient thermal management, sturdiness & excellent corrosion resistance & High quality toughened glass with 4mm thickness in clear finish for uniform light distribution. SS grade metal gland provided for 3 core 1sq mm supply wire. Length 208mm, Width 100 mm and Height 390mm including spike. Life time shall be at least of L70B50@50000 hours and the housing provides IP66 and IK 07 protection for high reliability in outdoor applications with Total System wattage not exceeding 25W. High efficiency long life COB mounted on PDC heat sink with holder and chrome finish reflector. Powered by an Built-In potted, electronic driver (SMPS based constant current supply) with lower THD < 10%, Output Open/ Short circuit protection, Surge voltage protection upto 4kV & other safety test as per IS:15885 Part 2/Sec 13.Lumen efficacy of LED > 140 lm/W. with aluminum heat sink for effective thermal management with Operating temperature: -10°C to +45°C. weighing 1.5 kg apprx. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 8 | Supply of exterior rated Architectural LED wall mounted luminaires with color temperature (CCT) of 3000K with CRI > 70 and medium beam light distribution. Luminaire Total System wattage 15W, with system lumen output > 1350 lumen with COB LED ON each side and operating voltage range 140- 270V AC.Aluminium enclosure with pressure die casting heat sink, Clear toughned Glass cover of 4mm thikness for high lumen output with Built-in, Potted electronic LED driver, THD < 10%, PF > 0.95, Over Voltage protection, inbuilt Surge Voltage protection upto 4k. Life time shall be at least of L70B50@50000 hours and IK07 & IP66 protection against weather. Fixture should have Height 250mm±1% and outer dia of 100 mm±1%, weighing about 1.40 kg+/-5%. The light fixture should have Operating Temperature Range from -10°C to 45°C. LED make should be only Cree , Lumined ,Nichia, Citizen, Edison, Osram, Bridgelux. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5 / Sec 1) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.fety certificate.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 9 | Supply, of exterior BIS registered 3000K Flexible LED Strip with 7.2 Watt per meter. LED Strip should have 30Nos LEDs per meter through out the length with the silicon cover with system lumens > 596lms/meter and System Lumen Efficacy > 75lm/w/meter. Standard Length of LED Strip is 5 mtr. The Strip should have IP 67 protection with inbuilt IP67 connectors at both ends. LED Strip shall be suitable to operate at an ambient temperature range of -20°C to 50°C. Life time shall be at least L70B50 @ 35000 burning hours at 50°C. LED should of make Nichea, Osram, Cree, Lumiled, Hongya of 5050 SMD package only. The rated voltage of the Luminaire should be 24VDC, Luminaire shall be offered with a BIS Approved Potted Driver of IP 66/67 rating made of extruded aluminium to make it more thermal efficient, Led Driver should have Operating input voltage range: 90-305Vac, PF > 0.95 and must have safety operation range form 90V - 176Vac. Life time of LED driver should be > 80,000 hours and MTBF of LED driver should be ≥ 2,00,000 hrs, Led driver must have SELV output and Case temperature i.e. Tc > 90°C. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (PART 5/SEC 7) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 10 | Supply of 90W RGBW LED Flood light, suitable for highlighting architectural features. Luminaire shall be capable of producing dynamic color changing light with 16 million colors, light fixture should be programmable using 8 bit control DMX512 communication protocol. Operating temperature: -20 °C to +50 °C, LED life L70B50: 70000 hours at 50°C. Lumen output should be of 4500 Lumens with Full LED on. CRI >= 80 for white LED, Housing made of Pure polyester powder coated Aluminum die cast housing in dark grey finish. Aesthetically designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant. Optics should be of PMMA Lens with Beam angle of different types such as narrow(10˚), medium(25˚), wide(40˚,60˚) or elliptical(18˚x 35˚) as per the site requirement. Fixture should be Toughened glass cover of 4mm thickness with High Impact Resistance strength of IK07 and IP66. LED should be of Osram/Lumileds/Cree, Built-In Potted IP66/67 electronic LED driver with APFC, lower THD, Open Circuit Protection, Over Voltage Protection, Surge Voltage Protection of 10kV with externally attached SPD. Minimum weight of fixture 3 Kg, Dimension of the fixture should be 330x321x62mm or more for better overall performance & long life. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 11 | Supply of 50W RGBW LED Flood light, suitable for highlighting architectural features. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 communication protocol. Operating temperature: -20 °C to +50 °C, LED life L70B50: 50000 hours at 50°C. Lumen output should be of 2500 Lumens with Full LED on. CRI >= 80 for white LED, Housing made of Pure polyester powder coated Aluminum die cast housing in White finish with aesthetically designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant, PMMA Lens, Beam angle of different types such as narrow(10˚), medium(25˚), wide(40˚,60˚) or elliptical(18˚x 35˚) as per the site requirement. Fixture should be Toughened glass cover of 4mm thickness with High Impact Resistance strength of IK07 and IP66. LED should be of Osram/Lumileds/Cree, Built-In Potted IP66/67 electronic LED driver with APFC,lower THD, Open Circuit Protection, Over Voltage Protection, Surge Voltage Protection of 10kV with externally attached SPD. Weight of fixture 3 Kg, Dimension of the fixture should be (282x274x66) mm or more for better overall performance & long life. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 12 | Supply of exterior rated Architectural Mono (3000K) Linear LED Wall Washer luminaire; suitable for facade lighting with extruded aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness with lens positioned screening to reduce the light spillage and die casted end caps. Total System wattage not exceeding 60W with system lumen output should be > 4000 lm with all LEDs on. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PMMA for each LED, offering beam angle of different types such as narrow(10˚), medium(25˚), wide(40˚,60˚) or elliptical(18˚x36˚) as per the site requirement. Fixture should have Height 50mm ± 5% including surface mount base width 50mm ± 5% , length 1000 mm ± 5% with constant locking hinges for simple position control from various angles without special tools.The rated voltage of the Luminaire should be 240Vac, Luminaire shall be offered with integral BIS Approved Potted Driver of IP 66/67 rating made of extruded aluminium to make it more thermal efficient, LED Driver should have Operating input voltage range: 90-305VAC, PF > 0.90. Life time of LED driver should be > 80,000 hours and MTBF of LED driver should be ≥ 2,00,000 hrs, Led driver must have SELV output and Case temperature i.e. Tc ≥90°C. Fixture should be available with 10KV SPD in CM/DM Mode. Fixture's DMX Signal cable should be available with proper loop in loop out features. Fixture shall be suitable to operate at an ambient temperature range of -20°C to 50°C and complete luminaire shall be IP66 and IK07 rated. LED Life time shall be at least L70B50 @ 50,000 burning hours at 50°C. LED should be with ceramic package of make Nichea, Osram, Cree, Lumiled only. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required. Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 13 | Supply of exterior rated Architectural LED Mono flood lighting luminaire; suitable for facade lighting with Die-cast aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness, Total System wattage not exceeding 130 W with system lumen output should be more than 10850 lm with all LEDs on. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PC for each LED, offering beam angle of different types such as narrow, medium, wide or elliptical as per the site requirement. Fixture should have Height 417 mm±1% including surface mount base and outer dia of 302 mm±1% with constant locking hinges for simple position control from various angles without special tools. Fixture shall be suitable to operate at an ambient temperature range of -30°C to 50°C and complete luminaire shall be IP66 and IK07 rated. LED Life time shall be at least L70B50 @ 70000 burning hours at 50°C. LED should be with ceramic package of make Nichea, Osram, Cree, Lumiled only. Luminaire shall be complete with integrated BIS IP 66/67 potted driver and capable of operating at line voltage from 90-305 Vac, 50Hz with power factor > 0.95. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 14 | Supply of 30W RGBW LED Flood light, suitable for highlighting architectural features. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 communication protocol. Operating temperature: -20 °C to +50 °C, LED life L70B50: 50000 hours at 50°C. Lumen output should be of 1800 Lumens with Full LED on. CRI >= 80 for white LED, Housing made of Pure polyester powder coated Aluminum die cast housing in White finish with aesthetically designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant, PMMA Lens, Beam angle of different types such as narrow(10˚), medium(25˚), wide(40˚,60˚) or elliptical(18˚x 35˚) as per the site requirement. Fixture should be Toughened glass cover of 4mm thickness with High Impact Resistance strength of IK07 and IP66. LED should be of Osram/Lumileds/Cree, Built-In Potted IP66/67 electronic LED driver with APFC,lower THD, Open Circuit Protection, Over Voltage Protection, Surge Voltage Protection of 10kV with externally attached SPD. Weight of fixture 3 Kg, Dimension of the fixture should be (282x274x66) mm or more for better overall performance & long life. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 15 | Supply of mono colour flood light luminaire made up of Pressure Die Cast Aluminum Body, High quality toughened glass in clear finish for uniform light distribution. Prismatic chrome plated reflector for controlled beam angle of 60°. System Wattage : 5W, IP rating – IP 66 & IK rating – IK 07, CRI > 80, CCT : 3000K, system lumen : 300 lms. Powered by an Built-In potted, electronic driver (SMPS based constant current supply) with lower THD, Output Open/ Short circuit protection, Surge voltage protection upto 4kV & other safety test as per IS:15885 Part 2/Sec 13.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 16 | Supply of DMX Splitter with Input Voltage range : 190-240V AC, Power Consumption 5W max. Housing is made of CRCA with powder coated finish Mounting, 19 inch rack mountable, Operation Temperature -30°C to +55°C, 8 Output with 3pin XLR terminal sockets, Ingress Protection Rating IP20. This unit takes the DMX Signal from DMX Controller & split the signal into 8 separate output channels. The output terminals of Splitters are optically isolated from the input. Splitters should be capable to amplify the DMX signal & allowing the data link to be extended by max. 300 m (1044 ft.) using AWG 22 DMX cable or 150 m (500 ft.) using AWG 24 DMX cable or maximum 20-25 fixture per output channel. To be provided with IP enclosure if installed in external environment.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 17 | Supply of DMX Controller for the system including all other accessories required for the running of the system Controller should have Input Power 5-5.5V DC 0.6A and Output Protocol DMX512 with 4 universe, 2 universe should work in Stand Alone Mode and 2 universe should work in live mode with laptop/ tablet / computer. The universe should be expandable from 2 to 4 DMX512 universes. It should be compatible for Programmability with PC, Mac, Tablet, Smartphone by using USB & Ethernet .Dmx controller should have network controllability feature to control the scene remotely through LAN and triggered via UDP packets on port 2430. Its must have Connections Type C USB, XLR3, Ethernet, battery. There should be provision for Memory microSD card. Device should have Intuitive backlit keyboard with 10 presets and also have provision of kepad on device for changing scene manually from device. Device should be capable to work on Extended triggering possibilities (TCA) & also have Smart Upgrade Technology (SUT). It is an IP 20 unit and has an Operating Temperature of 0°C to 50°C. weight should not be more than 120g. OS Requirements for the controller is Mac OS X 10.8-10.12, Windows 7/8/10. Standards should be EC, EMC, ROHS. The controller should have a variety of features including 2048 DMX channels, clock/calendar, iPhone/iPad/Android remote control, Ethernet facilities, dry contact port triggering and multi-zone SD card memory. Network synchronization of one area across hundreds of universes with the possibility of 99 scenes across 5 areas with auto clock triggering for sunrise and sunset and as per the festivals for specific occasions. Device should be equipped with meta; clamp to mount on wall. All Dynamic LED lighting fixtures & controllers shall be of same make to avoid integration, synchronization, and maintenance issues in future. To be provided with IP 66 enclosure if installed in external environment.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 18 | Supply of DMX address writer to write automatically address of DMX fixtures.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 19 | Planning, Designing, Programming of all the light fixtures with integration into controller and making multiple programming in total of 5 different occasion. Synchronizing all fixtures into one.Make: Bajaj/Havells/K-Lite or equivalent as approved by Eng-in-charge |
| 20 | Supply installation commissioning of following sizes of power and data cable as mentioned:Make: R.R. Kabel/Polycab/3 x 2.5 sqmm Cu unarmored multistrand |
| 21 | 5 x 6 sqmm Cu unarmored multistrand |
| 22 | 4 x 16 sqmm Al armoured |
| 23 | Data cable Cat 6 |
| 24 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properlyconnected with the earth.Make: R.R. Kabel/Polycab/Havells16 sqmm |
| 25 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc.Make: R.R. Kabel/Polycab/Havells16 sqmm |
| 26 | Supply and fixing of horizontal air termination (roof conductor) of 25mm x 3mm G.I. strip, G.I. clamps on surface complete in all respectsMake: R.R. Kabel/Polycab/Havells |
| 27 | Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity |
| 28 | Supply of 7.5 KVA 3phase electrical panel having Auto ON/OFF timer switch complete with MCB, isolator & other safety features. |
| 29 | Supply of 7.5 KVA 3phase electrical panel having Auto ON/OFF timer switch complete with MCB, isolator & other safety features along with 01 No. UPS to protact DMX controller & Servo stabilizer. |
| 30 | Supply of 3.75 KVA 3phase electrical panel having Auto ON/OFF timer switch complete with MCB, isolator & other safety features. |
| 31 | Supply, installation, testing and commissioning of PVC Pipe of size 20 mm as per requirement for cable layingand its protection. |
| 32 | Supply, installation, testing and commissioning of PVC Pipe of size 40 mm mm as per requirement for cable layingand its protection.Make: R.R. Kabel/Polycab/Havells |
| 33 | Supply, installation, testing and commissioning of B Class GI Pipe of size 40 mm mm as per requirement for cable layingand its protection.Make: R.R. Kabel/Polycab/Havells Please Enable Macros to View BoQ information |
