|
| 1 | Excavation for foundation in hard murum including shoring and strutting , dewatering as necessary and disposing off excavated stuff as directed etc. complete. a) Upto 1.50m lift Normal Rate b) 1.50m to 3.00m lift, Add 10% c) 3.00m to 4.50m lift, Add 20% d) 4.50m to 6.0m lift, Add 30% |
| 2 | Back filling behind abutment ,wing wall and return wall as per drawings and technical specifications etc. complete. (by sandy material)./cutting bushes,grass and dressing shoulder to desired camber and disposing of excavated stuff up to road boundary etc complete. as directed by Engineer In Charge. |
| 3 | Providing and laying filter material under neath pitching in slopes as per drawings and technical specifications etc. complete. |
| 4 | Providing and laying Cast insitu / Ready Mix cement concrete in M15 of trap / granite / quartzite / gneiss metal for foundation and bedding / steps including steel centering , formwork , laying / pumping , compacting , roughening them if special finish is to be provided , finishing uneven and honey combed surface and curing etc . complete . The Cement Mortar 1:3 plaster is considered for rendering uneven and honey combed surface , only . Newly laid concrete shall be covered by gunny bag , plastic , tar paulin etc . ( Wooden centering will not be allowed . ) , with fully automatic micro processor based PLC with SCADA enabled reversible Drum Typemixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 5 | Providing and laying in situ / ready mix M-35 cement concrete of trap / granite / quartzite / gneiss metal for cast in citu R.C.C. solid piers , column etc . including provision of V shaped false joints to form suitable panels on the faces to approved design with compacting by vibrating and curing complete . Including plywood / steel formwork , centering (excluding dewatering by means of pump) and including bailling out water and including CM 1:3 curing complete. a) Height upto 5 M. (With Concrete Mixer) i) Height up to 5 m, normal rate. ii) Height 5 to 7.50 m, add 5 percent extra over basic rate. iii) Height 7.50 to 10 m, 7.50 percent extra. iv) Over 10 m Height , add 10 percent extra fore very 2.50 m rise with fine agreegates of required specifications ( VSI sand finely washed etc) |
| 6 | Providing, cutting, bending, hooking, tying and laying in position TMT FE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete. |
| 7 | Providing and laying insitu/ready mix M-35 plain cement concrete of trap/granite/quartzite/gneiss metal for cast insitu piers,abutment,returns,wings etc. including provision of \\"V\\" shaped false joints to form suitable panels on the faces to approved esign with compacting by vibrating and curing complete,including plywood/steel form work centering (excluding dewatering by means of pump ) and including bailling out water and curing finishing in CM 1:3 etc. complete . as directed by engineer incharge basicrate shall be increased for height above 5.00 m in following manners b) Height upto 5 M. (With Batch Mix Plant)With fully automatic microprocessor based PLC with SCADA enable with fine agreegates of required specifications ( VSI sand finely washed etc ) i) Height up to 5 m, normal rate. ii) Height 5 to 7.50 m, add 5 percent extra over basic rate. iii) Height 7.50 to 10 m, 7.50 percent extra. iv) Over 10 m Height, add 10 percent extra for every 2.50m rise. |
| 8 | Providing cutting, bending, hooking, tying and laying in position TMT FE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete. |
| 9 | Providing and laying insitu / ready mix M-35 cement concrete Trap / Granite / Quartzite / Gneiss metal for R.C.C.well curbs including necessary compacting by vibrating , finishing and curing complete . with fine agreegates of required specifications ( V S I sand finely washed etc )( excluding reinforcement and includings huttering) A ) With Batch Mix Plant With fully automatic micro processor based PLC with SCADA enabled. |
| 10 | Providing cutting, bending, hooking, tying and laying in position TMT FE 500 steel bars for reinforcement for all RCC works as per detailed drawings etc. complete |
| 11 | Providing and laying 6mm thick mastic asphalt wearing course on to pofdeck slab excluding prime coat with paving grade bitumen meeting the requiremens given in table500-29 , prepared by using mastic cooker and laid to required level and slope after cleaning the surface including providing antiskid surface with bitumen preoated fine grained hard stone chipping at an approximate spacing of 10 cm center to center in both directions , pressed in to surface when the temperature of surfaces not less than 100 degC, protruding 1 mm to 4mm over mastic surface as per clause 515 etc. complete. |
| 12 | Providing 100 mm diameter GI water spouts as per detailed drawings in RCC slab and wearing surface / kerb etc. complete. |
| 13 | Providing and fixing bearing completed per drawing and technical spacification Clause no. 2000, 2200,2300. Filler joint and mastic pad |
| 14 | strip seal type of expansion joint completed per drawing and technical spacification for+- 50 mm(as per schedule-H) |
| 15 | Providing and fixing bearing completed per drawing and technical specification Clause no. 2000, 2200,2300. Elastomeric bearing |
| 16 | Providing and laying Cast insitu / Ready Mix cement concrete in M15 of trap / granite / quartzite / gneiss metal for foundation and bedding / steps including steel centering , formwork , laying / pumping , compacting , roughening them if special finish is to be provided , finishing uneven and honey combed surface and curing etc . complete . The Cement Mortar 1:3 plaster is considered for rendering uneven and honey combed surface , only . Newly laid concrete shall be covered by gunny bag , plastic , tar paulin etc . ( Wooden centering will not be allowed . ) , with fully automatic micro processor based PLC with SCADA enabled reversible Drum Typemixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 17 | Providing and laying Cast insitu / Ready Mix cement concrete M-30 of trap/granite/quartzite/gneiss metal for R.C.C. work in foundations like raft,strip foundations,grillage and footings of R.C.C.columns and steelstanchions etc.columns as per detailed designs and drawing or as directed including Steel centering formwork , cover block slaying / pumping , compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc.complete.(Excluding reinforcement and structural steel ) .with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Panmixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 18 | Providing and laying filter material under neath pitching in slopes as per drawings andtechnical specifications etc. complete. |
| 19 | Providing and laying pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per dawing and technical specifications etc. complete. (by stone/boulder) |
| 20 | Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete. |
| 21 | Providing and laying insitu /ready mix M-40 cement concrete of trap / granite / quartzite / gniess metal for reinforced cement concrete block below the bearing including necessary scaffolding , plywood / steel formwork , compaction by vibrating , finishing in CM1:3 and curing complete (Excluding reinforcement) Using reversible drum type mixer/concrete batch mix plant(panmixer) with fine agreegates of required specifications ( VSI sand finely washed etc ) |
| 22 | Painting of CD no. and span arrangement as per technical specification |
| 23 | Providing and constructing RCC hand rail M-30 grade including cost of centring completed per drawing and technical spacification clause no. 809 and IRC 6 |
| 24 | Taking trial bores 75 to 100 mm for 53.0 to 88.9 mm core dia in rocks as specified below including all necessary materials such a soil , grease , steel boost an and such o thermaterials as required ( including conveying them at erialto site of work ) and Preserving the core sample serially on site of work and conveying the same to HQ of concernring office as directed. Quartzite with diamond drill with Ax Bit 0 to 50 metre Please Enable Macros to View BoQ information |
