|
| 1 | Repairs to Charpoy GI 32/25 mm ply top (Drg No FD-220R) |
| 2 | (a) Removing unserviceable ply top and S&F new plywood top of size 1980mmx900mmx12mm thick BWR grade ISI Marked . Plywood top shall be fitted with appropriate sizes of nuts and bolts with washer all as specified and shown on drawings and as directed. |
| 3 | (b) Removing of damaged/broken long rail from charpoy GI pipe and S&F new long rail made out of GI Pipe 32/25 mm bore (ISI marked) medium grade including threading both sides all as specified in Drg & directed. |
| 4 | (c) Removing of old damaged/broken short rail from Charpoy and making of short rail from old u/s long rail (retervied from ser item No 1.02 above) including threading & fixing in charpoy GI Pipe all as specified in Drg & directed. |
| 5 | (d) Removing of old damaged/broken leg from charpoy and making leg from old u/s short rail (retervied from ser item No 1.02 &1.03 above) including threading & fixing in charpoy GI Pipe all as specified in Drg & directed. |
| 6 | (e) Removing of old broken/damaged check nuts and S&F new check nuts of 32 mm dia heavy duty to Charpoy GI pipe all as specified in Drg & directed. |
| 7 | (f) Removing old broken/damaged GI elbow, 3 way, 32/25 mm bore and S&F new GI elbow, 3 way, 32/25 mm bore (ISI marked) to Charpoy GI pipe all as specified in Drg & directed. |
| 8 | (g) Removing damage/broken welded suports from charpoy GI Pipe 32/25 mm and S/F new support made out of 40 x 6 mm flat iron, 850 mm long duly welded to charpoy including applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified in Drawing and directed. |
| 9 | Repair to Charpoy IP folding (FD-388 & FD 388(R)) |
| 10 | (a) Removing of old unserviceable charpoy top and S & F new top of12 mm thick plywood BWR grade (ISI Marked ) with appropriate size nuts,bolts & washer including thightening the loose components complete all as specified in drg and directed. |
| 11 | (b) Removing of old unserviceable members of charpoy folding and S & F new members of 25 mm dia 2 mm thck MS condute fixed with gas welding as specified & shown in drg. |
| 12 | (c) M & L for preparation of old painted steel surfaces by scraping/rubbing with sand paper and filling depressions with putty where ever required and applying one coat of synthetic enamel paint of approved shade complete all as specified in drg and directed. |
| 13 | Repair to Chorpoy IP Hard top FD/MAP-II/01 |
| 14 | (a) Removing of old unserviceable ply wood from charpoy and S&F new 12 mm thick plywood, BWR grade, (ISI Marked) to the top of charpoy IP of appropriate size including fixing to charpoy using nuts, bolts and washers as shown on drg complete all as specified in drg and directed. |
| 15 | (b) M & L for preparation of old painted steel surfaces by scraping/rubbing with sand paper and filling depressions with putty where ever required and applying one coat of synthetic enamel paint of approved shade complete all as specified in and directed. |
| 16 | Repair to Chair Verandah (Drg No FD-19(M), FD-256, FD-359 & FD/E6/MAP-II/06 |
| 17 | (a) Re-caning of Chair Verandah with 4mm wide & 0.4mm thick half round plastic cane except border which shall be 5mm wide & 0.6mm thick flat super quality cream/ white colour including applying one coat of synthetic enamel paint White after preparation of surface to complete frame of chair all as specified and directed. |
| 18 | (b) Repairs to broken mild steel components of chair verandah with gas welding all as specified and directed. |
| 19 | (c) Removing old broken leg of chair verandah and providing new 20mm dia MS pipe 1.6mm thick complete with welding all as specified and directed. |
| 20 | (d) Removing old broken PVC seat & back of chair verandah and S & F new PVC seat & back 4 mm thick as specified and directed. |
| 21 | (e) S&F, PVC rubber Shoe/Toe of best quality for the legs of chairs after removing the old un- serviceable shoes all as specified and directed. |
| 22 | REPAIR TO TABLE DINING OR'S STEEL WITH ALUMINIUM TOP (Drg No FD-165) |
| 23 | (a) Removing existing unserviceable table top and S&F, new table top made from block board, grade 2 quality, interior grade, commercial type, 19mm thick, size 1910x 680mm (ISI Marked) duly covered with anodised aluminum sheet 22 gauge thick and fixed with screws to MS pipe frame all as shown in drawing and directed. |
| 24 | (b) M&L for gas welding to broken joints/spots of 25mm x 25mm square pipe frame all around all as specified and directed. |
| 25 | (c) Cutting of worn out/damaged legs of table and replaced with new MS square pipe piece 3\\" to 4\\" long including welding complete. |
| 26 | (d) M&L for painting to MS frame of table dining with one coat of black synthetic enamel paint including preparation of surfaces complete all as specified and as directed. |
| 27 | (e) Removing unserviceable hard rubber shoe from legs of table and S&F, new hard rubber shoes as per existing size complete. |
| 28 | Repair to Almirah Med Steel (Drg No FD-1032) |
| 29 | (a) M&L for one coat of synthetic enamal paint OG to internal/external surface & shelves completely after preparation of old painted surfaces by applying sand paper and filling with putty where ever required to Almirah Medium steel all as specified & directed . |
| 30 | (b) Removing of old broken/ unserviceabble shelves from Almirah Medium steel and S&F new shelves made out of 1mm thick MS sheet bent to shape required all as specified in drg & directed . |
| 31 | (c) Removing broken/ dacayed legs from exsiting Almirah medium steel and S&F new legs made out 1.00 mm thick MS sheet bend to shape all as specified in drg and directed . |
| 32 | (d) Removing of old unserviceable locking device three way from exsiting Almirah Medium steel and S&F new locking device made out of 10 mm dia MS bar round and 3 mm MS plate all as specified in drg and directed. |
| 33 | (e) Removing of broken/unserviceable handle from existing almirah large/medium and S&F new Chromium Plated steel handle 100mm long all as specified in drg & directed. |
| 34 | (f) Removing of old unserviceable lock from exsiting almirah Large/Med steel (Drg No FD-67(M), 1031 & 1032) and S&F new four lever lock with duplicate keys all as specified in drg & directed . |
| 35 | (g) Removing of old/broken cleats from existing Almirah large/medium steel with shelves (Drg No FD-67(M), 1031 & 1032) and S&F new cleats made out of 1.6 mm thick PBI sheet bend to shape and shall be fixed with nut & bolt to give support to shelves all as specified in drg & directed. |
| 36 | REPAIRS TO CHAIR TUBULAR STEEL WITH OR WITHOUT ARMS (Drg No FD-75(M) |
| 37 | (a) M&L for gas welding to broken members of chair tubular steel, with & without arms all as directed |
| 38 | (b) M&L for painting of MS frame of chair tubular steel with arms with one coat of olive green synthetic enamel paint all as specified and directed. |
| 39 | (d) Dismantling of unserviceable seat of chair tubular steel with arms and without arms, S&F new seat made out of Ist class hard wood frame of size 18\\"x16\\" and 18\\"x18\\", fixing to chair with 75 x 6mm GI nut and bolt, including canning with 2mm plastic cane white half round and 4 mm plastic cane for border all as per drawing . |
| 40 | (e) Dismantling to unserviceable back of chair tubular steel with arms and without arms, S&F of new back made out of Ist class hard wood frame of size 16\\"x16\\" and 18\\"x15\\", fixing to chair with 75 x6mm GI nut & bolt, including canning with 2mm plastic cane white half round and 4 mm plastic cane for border all as per drawing . |
| 41 | (f) S&F of plastic cap 19mm dia to plug the open end of pipe of chair as shown in drawing . |
| 42 | (g) Dismantling of unserviceable hand rest and S&F new hand rest made out of Ist class hard wood duly painted with black colour complete all as shown in drawing and directed |
| 43 | REPAIR TO FORM WITH BACK (Drg No FD-78) |
| 44 | (a) S&F, seat made out of 1st class hard wood (Sal) of size 1800mm x 235mm x 40mm fixing with round head nut & bolt 75mm x 6mm to the MS frame of form with back including polishing to wooden seat complete all as shown on drawing, specified and directed. |
| 45 | (b) S&F, back rest made out of 1st class hard wood (Sal) of size 1800mm x 150mm x 25mm fixing with round head nut & bolt 75mm x 6mm to the MS frame of form with back including polishing to wooden back rest complete all as shown on drawing, specified and directed. |
| 46 | (c) M&L for Welding to broken joints of form with back of MS frame all as specified. |
| 47 | (d) Cutting of worn out/broken legs of form with back and S&F new square/round MS pipe 1.6mm thick of required size and fixing with gas welding complete all as shown on drawings. |
| 48 | (e) M&L for painting to complete MS frame of form with back with one coat of black synthetic enamel paint complete all as shown on drawing, specified and directed. |
| 49 | REPAIR TO TABLE 900MM X 600MM X 760MM WITH DRAWER/WITHOUT DRAWER STEEL (Drg No FD-1008 & FD-1007 ) |
| 50 | (a) Taking down unserviceable table top and S&F new top of 18 mm thick prelaminated particle board, interior grade, solid core with melamine face on one side and balancing white on other side including 4 mm thick teak wood edging all around complete all as shown on drawing. |
| 51 | (b) M&L for gas welding to broken joints of table Steel all as specified . |
| 52 | (c) Removing of unserviceable locks of drawer and supply & fixing new four lever locks with key in duplicate all as specified in drawing. |
| 53 | (d) Repairs to the drawer of table steel by making good dents, proper alignment for smooth function of drawer and preparation of old surfaces, inside and outside of drawer and legs & applying one coat of olive green paint by spray painting all as specified and directed. |
| 54 | Repair to Chair Dinning (Drg No. FD-203, 226, 228, 279, 353 & 354) |
| 55 | (a) M&L for removing of old broken rear leg of chair dinning and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 56 | (b) M&L for removing of old broken front leg of chair dinning and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg. |
| 57 | (c) M&L for removing of old broken stifner of chair dinning and S&F new stifner made out of first class hard wood (teak wood) of similar size & shape complete as specified & shown in drg. |
| 58 | (d) M&L for removing of old broken front/side/rear rail of chair dinning and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg. |
| 59 | (e) M&L for removing of old broken back rest of chair dinning and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg. |
| 60 | (f) M&L for removing of old unserviceable PVC seat of chair and S&F new PVC seat of 4mm thick and fixing with suitable screws all as specified and directed. |
| 61 | (g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of chair dining all as specified and directed. |
| 62 | (h) Re-caning of Chairs with 2mm wide & 0.4mm thick half round plastic cane except border which shall be 3.5mm(Minimum) wide & 0.6mm thick, frest all as per item No 10.01. |
| 63 | Repairs to Chair Easy (Drg No. FD-229, 17M, 201) |
| 64 | (a) M&L for removing of old broken rear leg of chair easy and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 65 | (b) M&L for removing of old broken front leg of chair easy and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 66 | (c) M&L for removing of old broken front/side/rear rail of chair easy and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg. |
| 67 | (d) M&L for removing of old broken top/bottom/side rail of back rest of chair easy and S&F new top/bottom/side rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg. |
| 68 | (e) M&L for removing of old broken arms of chair easy and S&F new arm made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 69 | (f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of chair easy all as specified and directed. |
| 70 | (g) Re-caning of Chairs with 2mm wide & 0.4mm thick half round plastic cane except border which shall be 3.5mm(Minimum) wide & 0.6mm thick, rest all as per item No 11.01 |
| 71 | Repairs to Chair Writing (Drg No. FD-280, 20M, 202, 250) |
| 72 | (a) M&L for removing of old broken rear leg of chair writing and S&F new rear leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 73 | (b) M&L for removing of old broken front leg of chair writing and S&F new front leg made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 74 | (c) M&L for removing of old broken stifner of chair writing and S&F new stifner made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 75 | (d) M&L for removing of old broken front/side/rear rail of chair writing and S&F new front/side/rear rail made out of first class hard wood (teak wood) of similar size & shape including drilling holes for caning all as specified & shown in drg. |
| 76 | (e) M&L for removing of old broken arms of chair writing and S&F new arm made out of first class hard wood (teak wood) of similar size & shape complete all as specified & shown in drg. |
| 77 | (f) M&L for removing of old broken back rest of chair writing and S&F new back rest made out of first class hard wood (teak wood) of similar size & shape all as specified & shown in drg |
| 78 | (g) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of chair writting all as specified and directed. |
| 79 | (a) Re-caning of Chair Writing with 4mm wide & 0.4mm thick half round plastic cane except border which shall be 5mm wide & 0.6mm thick flat super quality cream/ white colour rest all as specified in 12.01. |
| 80 | Repair to Chair writing with cushion seat & back ( Drg No FD/E6/MAP/12 ) |
| 81 | Taking out unserviceable components without damaging the serviceable components, Supply and Fix New components as per drawing and also matching with existing components, rest all as specified and directed by the Engineer-in-Charge.(a) S&F new seat with appropirate approved quality. |
| 82 | (b) S&F new back with appropriate approved quality, rest all as per item No 2.01. |
| 83 | (c) S&F new arm rest (handle), rest all as per item No 2.01. |
| 84 | (d) S&F new rubber stopper, rest all as per item No 2.01. |
| 85 | (e) M&L for welding of MS tubular frame of chari writing, rest all as per item No 2.01. |
| 86 | (f) M&L for one coat of synthetic enamel paint on MS tubular fram, rest all as per item No 2.01. |
| 87 | Repairs to Teapoy Wooden (Drg No. FD-382, 232, 34M, 278) |
| 88 | (a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg. |
| 89 | (b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg. |
| 90 | (c) M&L for removing of old unservicable front/rear rails, and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg. |
| 91 | (d) M&L for removing of old unservicable bottom rails and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg. |
| 92 | (e) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of teapoy all as specified and directed. |
| 93 | REPAIR TO TABLE 900 MM x 600 MM x 760 (WITH/WITHOUT DRAWER) (Drg No. FD-41, 42(M) & 224, FD-228,279, 16M, 203,55,223 & 284) |
| 94 | (a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg. |
| 95 | (b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg. |
| 96 | (c) M&L for removing of old unservicable long rail and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg. |
| 97 | (d) M&L for removing of old unservicable short rail and S&F, new teak wood short rail duly finished/smoothened complete all as specified & shown in drg. |
| 98 | (e) M&L for removing of old unservicable middle stiffener and S&F, new teak wood middle stiffener duly finished/smoothened complete all as specified & shown in drg. |
| 99 | (f) M&L for removing of old unservicable side stiffener and S&F, new teak wood side stiffener duly finished/smoothened complete all as specified & shown in drg. |
| 100 | (g) M&L for removing of old unservicable drawer and S&F, new drawer made out of Ist class hard wood and 6mm thick ply wood for bottom of drawer complete all as specified & shown in drg. |
| 101 | (h) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of table all as specified and directed. |
| 102 | Repairs to Table 900 x 900 x 760 mm (Drg No. FD-88M, 288 & 291) |
| 103 | (a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg. |
| 104 | (b) M&L for removing of old unservicable rails and S&F, new teak wood rail duly finished/smoothened complete all as specified & shown in drg. |
| 105 | (c) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg. |
| 106 | (d) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of table all as specified and directed. |
| 107 | REPAIR TO TABLE DINING 6 PERSONS (Drg No. 273 & FD/E6/MAP-II/03) |
| 108 | (a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg. |
| 109 | (b) M&L for removing of old unservicable long rails and S&F, new teak wood long rail duly finished/smoothened complete all as specified & shown in drg. |
| 110 | (c) M&L for removing of old unservicable top side rails and S&F, new teak wood top side rail duly finished/smoothened complete all as specified & shown in drg. |
| 111 | (d) M&L for removing of old unservicable top side short rails and S&F, new teak wood top side short rail duly finished/smoothened complete all as specified & shown in drg. |
| 112 | (e) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg. |
| 113 | (f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of table all as specified and directed. |
| 114 | REPAIR TO Peg Table (Drg No. FD-266, FD-277, FD-384, 25M) |
| 115 | (a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg. |
| 116 | (b) M&L for removing of old unservicable legs and S&F, new teak wood legs duly finished/smoothened complete all as specified & shown in drg. |
| 117 | (c) M&L for removing of old unservicable front & rear rail and S&F, new leg made out of 1st class hard wood teak duly finished/ smoothened complete all as specified & shown in drg. |
| 118 | (d) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of peg table all as specified and directed. |
| 119 | REPAIR TO TABLE DRESSING GENTS WITH MIRROR (Drg No. FD-230,31M & FD/E6/MAP/16) |
| 120 | (a) M&L for removing old unservicable back side of the box of table and S&F, new back side of the box of table made out of 12mm thick, teak wood planks in one piece, complete all as specified and shown on drawing. |
| 121 | (b) M&L for removing old unservicable top of the box of table and S&F, new top of the box of table made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg. |
| 122 | (c) M&L for removing old unservicable bottom of the box of table and S&F, new bottom of the box of table made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg. |
| 123 | (d) M&L for removing old unservicable side and partition and S&F, new side and partition made out of prelaminated particle board 12mm thick exterior grade (ISI marked), with one side teak face and balancing white on other side complete all as specified & shown in drg. |
| 124 | (e) M&L for removing old looking mirror of table and S&F new electro copper plated mirror totally free from distoration of 1100x550x5.5mm thick with teak wood frame of 25x25mm and with 6mm thick, commercial, BWR grade ply wood, rest all all as specified and shown on drawing. |
| 125 | (f) M&L for preparation of surfaces by cleaning with emery paper to obtain clean surface and using putty where ever required and polishing two coat of Melamyne polish to old and new surface of table dressing gents all as specified and directed. |
| 126 | REPAIR TO TABLE BED SIDE (Drg No. FD-276) |
| 127 | Taking out unserviceable components without damaging the serviceable components, Supply and Fix New components as per drawing and also matching with existing components, including sanding, rubbing, putty and painting one coat of synthetic enamel paint over one coat of red oxide to a new part of on full item after repairs all as specified and directed by Engineer-in-Charge.(a) S&F new MS 18mm size square pipe of 18 Gauge thick, length n.exc 600mm each part for various parts. |
| 128 | (b) S&F new handles for drawer 75mm long mild steel chromium plated rest all as per item No 16.01.. |
| 129 | (c) S&F new sides with 18 mm thick Pre lamineted particle board, rest all as per item No 16.01.. |
| 130 | (d) S&F new top with 18 mm thick Pre lamineted particle board, rest all as per item No 16.01.. |
| 131 | (e) S&F new drawer all as per drg & directed. |
| 132 | (f) S & F Stainless steel Telescopic rolling channel for Table of makes/ Models of Dumro, Godrej,Nilkamal,Durian, rest all as per item No 16.01.. |
| 133 | REPAIR TO TABLE 900 MM x 900 MM x 760 MM STEEL (Drg No. FD-121(M) |
| 134 | (a) M&L for removing old unservicable top and S&F, new top made out of prelaminated particle board 18mm thick exterior grade (ISI marked), with one side melamine face and balancing white on other side with 4 mm thick teak wood edging alround all as specified & shown in drg. |
| 135 | (b) M&L for Gas welding to broken joints of table steel all as specified and directed. |
| 136 | (c) Cutting of worn out portion of legs of table and S&F new 25x25mm square pipe of 1.6mm thick piece of 3” to 4” long including gas welding complete all as specified and directed. |
| 137 | (d) M&L for preparation of old painted surface and applying one coat of black synthetic enamel paint complete all as specified and directed. |
| 138 | REPAIR TO STOOL STEEL 2' HEIGHT (DRG No FD-81(M)) |
| 139 | (a) Preparation of old painted surface and applying one coat of Olive Green synthetic enamel paint complete all as specified and directed. |
| 140 | (b) Removing of old unserviceable stool top and S&F, new top of stool of 1.6mm thick MS sheet (top size 305 x 305) complete all as specified and shown on drawing. |
| 141 | (c) Removing of old unserviceable legs of stool and S&F, new legs of stool of 1.6mm thick MS sheet complete all as specified and shown on drawing. |
| 142 | (d) Removing of old unserviceable broken top rail of stool and S&F, new top rail of stool of 1.6mm thick MS sheet complete all as specified and shown on drawing. |
| 143 | REPAIR TO CHAIR REVOLVING With/ Without Arms & Computer Chair TP & FD/E6/MAP/01 |
| 144 | Taking out unserviceable components without damaging the serviceable components, Supply and Fix New components as per drawing and also matching with existing components, rest all as specified and directed by Engineer-in-Charge.(a) S & F new hand rest. |
| 145 | (c) S & F new back, rest all as per item No 12.01.. |
| 146 | (c) S & F new seat with PVC lipping alround , rest all as per item No 12.01.. |
| 147 | (c) S & F new pedestal assy and hydrolic pump, rest all as per item No 12.01.. |
| 148 | (d) Preparation of old painted surface of chair revolving and applying one coat of synthetic enamel paint by spray with black enameled colour all as directed. |
| 149 | M&L FOR STORE INDENTIFICATION BOARD AT BS YARD STORES |
| 150 | Taking out unserviceable components without damaging the serviceable components, Supply and Fix New components as per drawing and also matching with existing components, rest all as specified and directed by Engineer-in-Charge.(a) S&F, new ply wood 12mm thick, BWR grade, ISI marked including fixing with suitable size screw & cup washer complete over a coat of synthetic enamel paint all as shown on drg and specified. |
| 151 | (b) S&F new head rest of 18mm thick prelaminated particle board, rest all as per item No. 24.01 |
| 152 | (c) S&F new foot rest of 18mm thick prelaminated particle board, rest all as item No. 24.01 |
| 153 | (d) M&L for retightening of loose components, welding, replacmemnt of old nuts & bolts, rest all as per item No. 24.01 |
| 154 | M&L FOR STORE IDENTIFICATION BOARD AT BS YARD STORES |
| 155 | M&L in replacement for providing and fixing store identification board of size 18\\" × 48\\" made out of 3 mm thick Aluminium Composite Panel (ACP) of approved colour fixed over 25 mm × 25 mm × 3 mm MS angle frame, frame duly fabricated, welded and grinded smooth and treated with one coat red oxide primer and two coats synthetic enamel paint. Board face to have weather resistant vinyl / retro-reflective vinyl lettering indicating description / name of store, the content to be written in CAPITAL LETTERS IN ENGLISH with corresponding HINDI text beneath the English text, letters of suitable size and approved colour. Including drilling holes and fixing with suitable size rawl bolts / anchor fasteners to the front wall of store, sealing edges with silicon sealant and making good disturbed surfaces complete. All materials, labour, tools, tackles, scaffolding etc complete all as specified and directed by Engineer-in-Charge. |
| 156 | M&L in replacement for providing and fixing hemispherical type main gate identification board made out of 3 mm thick Aluminium Composite Panel (ACP) of approved colour having overall span approximately 18.75 feet and board width 1.5 feet, fixed over 25 mm × 25 mm × 3 mm MS angle frame conforming to hemispherical profile, frame duly fabricated, welded and grinded smooth and treated with one coat red oxide primer and two coats synthetic enamel paint. The front face of the board shall be provided with 3 mm thick ACP sheet fixed to the frame and the rear face shall also be covered with 3 mm thick ACP sheet of approved colour so as to form a closed box type structure. The exposed edges and sides shall be finished with matching ACP return strips of depth equal to frame depth to completely conceal the MS frame and provide a neat finished appearance from all sides. The board face shall have weather resistant retro-reflective vinyl lettering/graphics indicating office information such as “WELCOME TO BSO GANDHINAGAR / GE (ARMY) GANDHINAGAR”, the content to be written in CAPITAL LETTERS IN ENGLISH with corresponding HINDI text beneath the English text, in letters of suitable size and approved colour. The board shall be mounted above gate columns with MS supporting brackets including height adjustable arrangement using slotted plates, nuts and bolts to maintain adequate clearance for trucks/containers passing through the gate. Including drilling holes, fixing with suitable size rawl bolts/anchor fasteners, sealing edges with silicon sealant and making good disturbed surfaces complete. All materials, labour, tools, tackles, scaffolding etc complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
